Effect of temperature on the surface free energy of amorphous carbon films

Diamond-like carbon (DLC) and tetrahedral amorphous carbon (ta-C) have attracted much attention recently for biomedical and antifouling applications due to their excellent biocompatibility and inherent nonstick properties. It has been demonstrated that the solid surface free energy is a dominant factor in cellular or fouling adhesion. However, few data for the surface free energy of DLC and ta-C coatings at temperatures in the range 37-95 degrees C are available. In this study DLC and ta-C coatings on stainless steel 304 sheets were prepared using an unbalanced magnetron sputtering system and a filtered cathodic vacuum arc system, respectively. The contact angles of water, diiodomethane and ethylene glycol on the coated surfaces at temperatures in the range 20-95 degrees C were measured using a Dataphysics OCA-20 contact angle analyzer. The surface free energy of the coatings and their components (e.g., dispersion, polar or acid/base portions) were calculated using various methods. The experimental results showed that the total surface free energy and dispersive surface free energy of the ta-C coatings, DLC coatings, stainless steel 304 and titanium decreased with increasing surface temperature, while the acid-base SFE component increased with increasing temperature.     

Morphology controls of the melt blending in a novel highly crosslinked bismaleimide system

A novel bismaleimide of 2,2-bis[4-(4-maleimidophenoxy)phenyl]propane (BMIP) with a broad working-temperature-range for the melt blending was successfully synthesized. BMIP possesses a considerably broad working-temperature-range from 75 °C to 250 °C, prior to undergoing cure reactions to form a highly crosslinked network. The morphology types of cured BMIP/clay hybrids can be controlled by varying the shearing temperatures and the contents of the clay. The conditions necessary for achieving an exfoliated or an intercalated BMIP/clay hybrid were thoroughly investigated via X-ray diffractometry, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). All the uncured samples prepared at different shearing temperatures and with an adequate amount of MMT-C (above 3 phr) exhibited an intercalated form of morphology. However, the crosslinking reactions for specified samples prepared at relatively elevated shearing temperatures (above 120 °C) and with a relatively low content of clay (below 15 phr) resulted in morphology changes from the intercalated form to the exfoliated form of morphology. There exists an isotropically mechanical property for the cured matrix of the exfoliated hybrids whereas there exists an anisotropically mechanical property for the cured matrix of the intercalated hybrids.     

Synthesis, crystal structure, and properties of MnNCN, the first carbodiimide of a magnetic transition metal

Synthesis, single-crystal structure determination, and magnetic properties are reported for manganese carbodiimide, MnNCN. The presumably unstable but inert phase adopts the trigonal system (R3m) with a = 3.3583(4) A, c = 14.347(2) A, V = 140.13(3) A3, and Z = 3. Divalent manganese is octahedrally coordinated by nitrogen atoms at 2.26 A, and the NCN(2-) unit adopts the linear [N=C=N](2-) carbodiimide shape with two C=N double bonds of 1.23 A. MnNCN contains high-spin Mn(II) with five unpaired electrons and behaves like an antiferromagnet with an ordering temperature below 30 K.     

Theoretical study of the ring‐closing reaction of 5′‐AMP to cAMP and H2O in the gas phase

The ring‐closing reaction of 5′‐adenosine monophosphate (5′‐AMP) to generate cyclic 3′, 5′‐adenosine monophosphate (cAMP) and H₂O was theoretically investigated at the B3LYP/6‐31G**level. It was found that the ring‐closing reaction of 5′‐AMP may proceed in a synchronous way or in a stepwise way. For the latter, the reaction is a multichannel elimination reaction including inner H transfer. The potential energy surface of Path 3 is lowest in all the ring‐closing reaction paths. In addition, H shuttling reaction with the participation of a water molecule to act as a shuttle were also studied at the same level. The calculations indicate that the participation of a water molecule facilitates hydrogen transfer reaction. Our present calculations rationalized all the possible reaction channels. © 2005 Wiley Periodicals, Inc. Int J Quantum Chem, 2005     

Flow injection analysis methods for determination of diffusion coefficients

Two flow injection analyses (FIA) methods for the determination of diffusion coefficients in a straight single tube FIA system were developed. Based on the analytical solution of the convection-diffusion equation, linear relationships of the logarithmic values of the dispersion coefficient (D) and the half-peak width (W_1/2) with the diffusion coefficient (D_m) were obtained. Experiments were designed to verify these methods. For example, for potassium hexacyanoferrate (III) a D_m value of 0.72 × 10⁵ cm² s⁻¹ was found versus a literature value of 0.76 × 10⁵ cm² s⁻¹ (error, 5%). For potassium hexacyanoferrate (II) a D_m value of 0.67 × 10⁵ cm² s⁻¹ was obtained versus a literature value of 0.63 × 10⁵ cm² s⁻¹ (error, 6%). The diffusion coefficients of some important biomedical compounds, such as dopamine, epinephrine, norepinephrine and ascorbic acid, were then determined. The values of 10⁵ D_m/cm² s⁻¹ are 0.60 ± 0.03, 0.44 ± 0.02, 0.60 ± 0.01 and 0.68 ± 0.06, respectively.     

镧的植物防病效果及其生物学效应

通过灭菌土接种Rhizoctonia solani以及混合接菌Rhizoctonia solani和Fusarium solani进行盆栽试验,分别研究了镧浸种处理对高羊茅及板蓝根出苗、生长发育的影响。结果表明,镧浸种能明显地减少病原菌的侵染,对由其所造成的种腐、芽腐及根腐等有显著的防治效果,提高了板蓝根和高羊茅种子的出苗率。同时,镧浸种在适当的浓度范围内,还能显著地促进植物的生长发育,生物量明显增加。利用盆栽水稻试验研究了稀土镧对水稻纹枯菌(Rhizoctonia solani)的毒力,测定结果表明,镧喷施于水稻植株上对水稻纹枯病有明显的防治效果,且在活体条件下,喷施镧后1和7 d对水稻纹枯菌(Rhizoctonia solani)的有效中浓度分别为128.7和128.1 mg.L-1,均明显低于离体条件下的有效中浓度(171.9 mg.L-1)。