Thermal conductivity of crystalline chrysotile asbestos

The thermal conductivity of crystalline chrysotile asbestos made up of hollow tubular Mg₃Si₂O₅(OH)₄ filaments is measured in the range 5–300 K. The paper discusses the possibility of using this material in studies of the thermal conductivity of thin filaments of metals and semiconductors incorporated into the channels of crystalline chrysotile asbestos tubes.     

Effect of ion impinging on the microstructure and field emission of carbon nanotubes

Effects of ion impinging on the microstructure and field electron emission properties of screen-printed carbon nanotube films were investigated. We observed that the plasma treatment modified the microstructure of CNTs along with the remarkable increase of emission site density. With the prolongation of ion impinging time, the emission current falls down first, and then rises up to higher than that of the untreated films. It is proposed that the change of emission characteristics is due to the different emission mechanisms. After the treatment, electrons are emitted predominantly from the nano-nodes on the tube wall instead from the nanotube tips.     

Crystallographic report: catena‐Aqua(2,2′‐bipyrimidine)lithium(I) perchlorate

A lithium(I) coordination polymer has been formed from LiClO₄ and the 2,2′‐bipyrimidine (bpym) ligand in which each square pyramidal lithium(I) atom is coordinated in the basal plane by four nitrogen donor atoms derived from two bpym ligands and one water molecule at the apical position. These are connected into a layer structure via hydrogen‐bonding interactions involving the perchlorate anions. Copyright © 2004 John Wiley & Sons, Ltd.     

Exciton Molecules in Quantum Wells: Influence of the Well Width Fluctuations

The influence of the well width fluctuations on the dependence of the binding energy of excitonic complexes in quantum wells is studied by using the path-integral Monte-Carlo technique. The results are compared with available experimental data and a good agreement is found.Postdoctoral researcher of FWO-Vlaanderen     

On the Possibility of Replacing Standard Chromium-Plating Electrolytes with Sulfate-Oxalate Solutions of Cr(III)

A method for preparing sulfate-oxalate chromium-plating solutions by reducing Cr(VI) from industrial chromium-plating electrolytes to Cr(III) with a Na₂SO₃ solution is proposed.     

Polarization dynamics of intracavity frequency-doubled Nd:YAG laser

Experimental study of low-frequency dynamics of an intracavity frequency-doubled Nd:YAG laser demonstrates the influence of the interaction of orthogonally polarized modes, participating in frequency doubling (type II phase matching), on the stability of the laser output. At a sufficiently low pump rate and low conversion efficiency, the laser shows stable operation with a low noise level at the frequencies of relaxation oscillations. At a high pump power and/or a high conversion efficiency, the laser emission becomes unstable as a result of Hopf bifurcation at the frequencies of relaxation oscillations that are responsible for the anti-phase polarization dynamics of the laser.     

What Oxidation State of Iron Determines the Amethyst Colour?

A colourless quartz crystal doped with ⁵⁷Fe³⁺ was obtained by hydrothermal synthesis in an NH₄F solution. The crystal was transformed into violet amethyst by gamma-irradiation. The change in colour was accompanied by changes in the Mössbauer spectrum that can be interpreted as the conversion of trivalent iron into the tetravalent state: Fe³⁺→Fe⁴⁺.

     

The mechanism of emission in the red photoluminescence band of porous silicon

Porous silicon (PS) exhibits several photoluminescence (PL) bands, whose spectral position and intensity depend strongly on the actual conditions of preparation of PS, its treatment, and subsequent use. The PS PL band peaking at about 1.8 eV and usually assigned to the intrinsic emission of silicon nanocrystals was studied. It was shown that the temperature-induced variation of the PL kinetics in the 80 to 300-K interval follows a complex pattern and depends noticeably on the actual point on the band profile. The temperature behavior of PL decay in the 1.8-eV band is determined by the electron-hole recombination rate within a nanocrystal and the cascade carrier transitions from small to large nanocrystals, with an attendant decrease in energy.     

A fast method to measure the thickness of removed layer from etching of SSNTD based on EDXRF

Solid state nuclear track detectors are commonly used for measurements of concentrations of radon gas and/or radon progeny. All these measurements depend critically on the thickness of the removed layer during etching. However, the thickness of removed layer calculated using the etching period does not necessarily provide a sufficiently accurate measure of the thickness. For example, the bulk etch rate depends on the strength of stirring during etching for the LR 115 detector. We propose here to measure the thickness of the removed layer by using energy-dispersive X-ray fluorescence spectrometry. In the present work, a reference silver nitrate pellet is placed beneath the LR 115 detector, and the fluorescence X-ray intensity for silver is then measured. We have found a linear relationship between the X-ray intensity and the thickness of the removed layer for LR 115 detector. This provides a fast method to measure the thickness of removed layer from etching of LR 115 detector. However, this method was found to be inapplicable for the CR-39 detector. Therefore, alternative methods have yet to be explored for the CR-39 detector.