Formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber blends: Effects of preparation method,composition, and thermal condition

The effects of preparation method, composition, and thermal condition on formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber (iPP/EPR) blends were studied using modulated differential scanning calorimeter (MDSC), wide angle X‐ray diffraction (WAXD), and phase contrast microscopy (PCM). It was found that the α‐iPP and β‐iPP can simultaneity form in the melt‐blended samples, whereas only α‐iPP exists in the solution‐blended samples. The results show that the formation of β‐iPP in the melt‐blended samples is related to the crystallization temperature and the β‐iPP generally diminishes and finally vanishes when the crystallization temperature moves far from 125 °C. The phenomena that the lower critical temperature of β‐iPP in iPP/EPR obviously increases to 114 °C and the upper critical temperature decreases to 134 °C indicate the narrowing of temperature interval, facilitating the formation of β‐iPP in iPP/EPR. Furthermore, it was found that the amount of β‐iPP in melt‐blended iPP/EPR samples is dependent on the composition and the maximum amount of β‐iPP formed when the composition of iPP/EPR blends is 85:15 in weight. The results through examining the effect of annealing for iPP/EPR samples at melt state indicate that this annealing may eliminate the susceptibility to β‐crystallization of iPP. However, only α‐iPP can be observed in solution‐blended samples subjected to annealing for different time. The PCM images demonstrate that an obvious phase‐separation happens in both melt‐blended and solution‐blended iPP/EPR samples, implying that compared with the disperse degree of EPR in iPP, the preparation method plays a dominant role in formation of β‐iPP. It is suggested that the origin of formation of β‐iPP results from the thermomechanical history of the EPR component in iPP/EPR. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1704–1712, 2007     

Operator‐splitting method for the analysis of cavitation in liquid‐lubricated herringbone grooved journal bearings

This paper presents an operator‐splitting method (OSM) for the solution of the universal Reynolds equation. Jakobsson–Floberg–Olsson (JFO) pressure conditions are used to study cavitation in liquid‐lubricated journal bearings. The shear flow component of the oil film is first solved by a modified upwind finite difference method. The solution of the pressure gradient flow component is computed by the Galerkin finite element method. Present OSM solutions for slider bearings are in good agreement with available analytical and experimental results. OSM is then applied to herringbone grooved journal bearings. The film pressure, cavitation areas, load capacity and attitude angle are obtained with JFO pressure conditions. The calculated load capacities are in agreement with available experimental data. However, a detailed comparison of the present results with those predicted using Reynolds pressure conditions shows some differences. The numerical results showed that the load capacity and the critical mass of the journal (linear stability indicator) are higher and the attitude angle is lower than those predicted by Reynolds pressure conditions for cases of high eccentricities. Copyright © 2004 John Wiley & Sons, Ltd.     

Numerical analysis of the rotating viscous flow approaching a solid sphere

A numerical simulation is performed to investigate the flow induced by a sphere moving along the axis of a rotating cylindrical container filled with the viscous fluid. Three‐dimensional incompressible Navier–Stokes equations are solved using a finite element method. The objective of this study is to examine the feature of waves generated by the Coriolis force at moderate Rossby numbers and that to what extent the Taylor–Proudman theorem is valid for the viscous rotating flow at small Rossby number and large Reynolds number. Calculations have been undertaken at the Rossby numbers (R_o) of 1 and 0.02 and the Reynolds numbers (R_e) of 200 and 500. When R_o=O(1), inertia waves are exhibited in the rotating flow past a sphere. The effects of the Reynolds number and the ratio of the radius of the sphere and that of the rotating cylinder on the flow structure are examined. When R_o ? 1, as predicted by the Taylor–Proudman theorem for inviscid flow, the so‐called ‘Taylor column’ is also generated in the viscous fluid flow after an evolutionary course of vortical flow structures. The initial evolution and final formation of the ‘Taylor column’ are exhibited. According to the present calculation, it has been verified that major theoretical statement about the rotating flow of the inviscid fluid may still approximately predict the rotating flow structure of the viscous fluid in a certain regime of the Reynolds number. Copyright © 2004 John Wiley & Sons, Ltd.     

Damage and fracture evaluation of granular composite materials by digital image correlation method

This paper presents the applications of digital image correlation technique to the mesoscopic damage and fracture study of some granular based composite materials including steelfiber reinforced concrete, sandstone and crystal-polymer composite. The deformation fields of the composite materials resulted from stress localization were obtained by the correlation computation of the surface images with loading steps and thus the related damage prediction and fracture parameters were evaluated. The correlation searching could be performed either directly based on the gray levels of the digital images or from the wavelet transform (WT) coefficients of the transform spectrum. The latter was developed by the authors and showed higher resolution and sensitivity to the singularity detection. Because the displacement components came from the rough surfaces of the composite materials without any coats of gratings or fringes of optical interferometry, both surface profiles and the deformation fields of the composites were visualized which was helpful to compare each other to analyze the damage of those heterogeneous materials. The project supported by the National Natural Science Foundation of China (10125211 and 10072002), the Scientific Committee of Yunnan Province for the Program of Steel Fiber Reinforced Concrete, and the Institute of Chemical Materials, CAEP at Mianyang     

Rod–coil block copolymers: An iterative synthetic approach via living free-radical procedures

A modular approach has been developed for the synthesis of rod–coil block copolymers involving the initial preparation of a macroinitiator based on the rod block followed by the growth of the coil segment with living free-radical procedures. The key feature of this strategy is the utilization of an alkoxyamine group from the beginning of the synthesis, which serves as a solubilizing group and ensures that each rod block contains a single initiating fragment. Using this approach permits block copolymers based on insoluble biphenyl ester oligomers to be conveniently prepared with coil segments that range from styrenes to acrylates to 1,3-dienes. The tendency of the rod segments to crystallize is strongly dependent on the weight fraction of the rod segment and the chemical nature of the coil segment. Rod–coil molecules containing at least 25–35 wt % polystyrene or poly(n-butyl acrylate) coil segments show a two-dimensional hexagonal arrangement of rod aggregates, as characterized by transmission electron microscopy and small-angle X-ray scattering. Polyisoprene block copolymers exhibit a lamellar microstructure with short rigid domains in which the rod units lie in an interdigitated smectic C arrangement. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3640–3656, 2003     

求解非对称线性方程组的QMRGCGS方法

1 引言 求解非对称线性方程组Ax=b的双共轭梯度方法(BCG)[3]和它的变形共轭梯度平方方法(CGS)[6]都有典型的不规则收敛行为,后来Freund和Nachtigal提出一种BCG类方法,即拟极小剩余方法(QMR)[7],用来补救BCG方法的收敛性并且产生了光滑的收敛曲线。然而,象BCG方法一样,QMR方法要用到系数矩阵A及其转置A~T与向量的乘积,为了解决这一问题,Freund提出TFQMR方法,此方法具有拟极小剩余性,同时不需用到A~T与向量的乘积。     

激光在医学中的应用

激光在医学领域的应用非常广泛，本文主要介绍了激光诊断和激光治疗的几个重要应用。     

新型菲涅尔线聚焦聚光太阳电池组件研究

以聚甲基丙烯酸甲脂为材料,采用热压成型工艺加工成型线聚焦菲涅尔聚光透镜(8×),可用于空间、地面光伏系统太阳电池组件的聚光系统,并对在其聚光条件下,太阳电池的电流电压特性进行测试,结果表明,该菲涅尔线聚焦棱镜能有效提高太阳电池的单位输出功率.模具的机械加工精度和光学抛光精度低,是造成其部分聚光率损失的原因.     

The Characteristic of Threading Dislocation in Different Structures GaN Films Grown by MOCVD

Three mechanisms to reduce threading dislocations(TDs) in GaN films as the epitaxial films grow thicker are suggested by SEM and TEM