Electrical Properties of Cylindrical Reverse Micelle

In this article, accurate analytic expressions of the surface charge density/surface potential and adsorption excesses for cylindrical reverse micelle in a solution of symmetric electrolyte are derived from the nonlinear cylindrical Poisson–Boltzmann equation. These expressions are in good agreement with numerical values and Van Aken's results for cylindrical reverse micelle with high surface potentials and large κa.     

Surface-Modified Sb2S3 Nanoparticles and Their Tribological Behaviors in Liquid Paraffin

Sb₂S₃ nanoparticles surface-modified with S-tetradecyl N, N-dihydroxyethyl dithiocarbamate (C₁₄DTC-Sb₂S₃) have been synthesized via extraction of Sb₂S₃ colloidal particles from ethylene glycol into toluene in the presence of C₁₄DTC. The obtained products were characterized by high-resolution transmission electron microscope (HRTEM) and Fourier transformation infrared (FTIR), and their tribological behaviors as an additive in liquid paraffin were investigated using a four-ball tribometer. The results show that C₁₄DTC-Sb₂S₃ nanoparticles can significantly improve the friction reduction, anti-wear, and load-carrying properties of base oils. The preliminary lubrication mechanism was discussed based on the SEM and XPS investigation of the rubbed surfaces.     

Fabrication and characterization of an irradiation facility for large-sample geometry

An irradiation facility consisting of a modified beam port shielding plug has been designed, fabricated built and characterized for use in irradiating non-standard sample geometries. The shielding plug features a graphite moderator at the core end with a hole, or “well” drilled of sufficient diameter and depth to accommodate an eight ounce (227 gram) sample bottle. Added shielding behind the graphite consists of castable neutron- and -gamma-ray shielding. The modified shielding plug can be removed relatively quickly from its irradiation position to minimize personnel exposures. It is mounted in close proximity to the Ohio State University Research Reactor reactor core to allow performance of high-sensitivity neutron activation analysis studies. Using the SAND-II unfolding code, the energy-dependent neutron flux has been measured in the sample irradiation position. When operating at 100 % power, the total flux is 3.9 × 10¹² n/cm²/s. Of this, 55 % is thermal (<0.5 eV), 23 % is epithermal (>0.5 eV, <0.5 MeV), and 22 % is “fast” (>0.5 MeV). This makes the facility suitable for neutron activation studies. Recently it has been used for irradiation of filter papers collected in a study of particulate air pollution in the form of atmospheric particulate matter in an urban environment.     

纳米金标记抗体增强SPR检测大肠杆菌O157∶H7

将金纳米粒子(AuNPs)标记的大肠杆菌O157∶H7(E.coli O157∶H7)的多克隆抗体(PAb)作为二抗,采用氨基偶联法将PAb固定在传感器表面作为一抗,通过三明治方法用双通道表面等离子体子共振(SPR)传感器对E.coli O157∶H7进行检测,并与SPR直接法检测进行了比较.结果表明,直接法的检出限为103cfu/mL,线性范围为103～109cfu/mL;AuNPs增强三明治法的检出限为10 cfu/mL,线性范围为10～1010cfu/mL,灵敏度比直接法提高了100倍,且具有更宽的检测范围.本方法不仅检测时间短,而且具有良好的选择性和重现性.     

改性Y型分子筛对FCC汽油脱硫性能的研究

采用液相离子交换法制备了Cu(I)Y、NiY、CeY分子筛,利用XRD、ICP/MS、N₂吸附脱附等技术对其物化性质进行了表征,使用固定床技术和色谱-硫化学发光检测(SCD)偶联技术系统考查了改性Y分子筛对FCC汽油的选择性吸附脱硫性能,着重探讨了FCC汽油选择性吸附脱硫过程中硫化物的脱除规律。结果表明,不同金属阳离子改性的Y分子筛对FCC汽油中不同硫化物选择性有所不同,对CeY分子筛:2-甲基-5-乙基噻吩<噻吩3硫醇< C₂噻吩<2或3-甲基噻吩<苯并噻吩<3,4-二甲基噻吩≈2,3,4-三甲基噻吩<四氢噻吩,而NiY与Cu(I)Y选择性相同:C₃硫醇<2-甲基-5-乙基噻吩2噻吩<2或3-甲基噻吩<噻吩<苯并噻吩<3,4-二甲基噻吩≈2,3,4-三甲基噻吩<四氢噻吩,改性Y分子筛对噻吩及小分子烷基取代噻吩类硫化物的选择性较差。     

多孔炭载聚钴酞菁修饰电极用于苯二酚的电催化及检测

以二氧化硅纳米球为模板,通过葡萄糖的水热聚合反应制备了具有三维结构的多孔炭(PC)。采用电化学聚合方法将单体钴酞菁聚合在多孔炭修饰的玻碳电极(PC/GC)表面,制备了多孔炭载聚钴酞菁的修饰电极(Co-TAPc/PC/GC)。通过循环伏安法(CV)研究了间苯二酚、邻苯二酚和对苯二酚在此修饰电极的电化学响应。结果表明,相对于裸玻碳电极、多孔炭或聚钴酞菁单独修饰的电极,该修饰电极对3种同分异构体的酚类物质均有更好的电催化活性。利用计时安培技术,该修饰电极对间苯二酚、邻苯二酚及对苯二酚分别在5.0×10-6～5.0×10-4 mol/L,6.0×10-6～2.5×10-4 mol/L和2.0×10-6～8.0×10-4 mol/L范围内具有较好的线性响应。此修饰电极具有制备简单、响应灵敏、稳定性好等优点。     

免疫亲和柱净化-液相色谱-串联质谱法同时测定猪肉中6种玉米赤霉醇类化合物残留量

建立了猪肉中6种玉米赤霉醇类化合物残留量的免疫亲和柱净化-液相色谱-串联质谱(IAC-LC-MS/MS)分析方法。酶解后的样品用乙醚提取,提取液浓缩后用三氯甲烷溶解,NaOH溶液反萃取,经免疫亲和柱富集和净化后,采用LC-MS/MS进行测定,外标法定量。在Shimadzu Shim-pack VP-ODS C18反相柱上分离,梯度洗脱,流动相为乙腈和2 mmol/L乙酸铵溶液;质谱采集为电喷雾负离子多反应监测模式。6种目标物的线性范围为0.5～200μg/L,相关系数(R)大于0.999,定量限(LOQ)在0.05～0.63μg/kg之间;添加浓度在1.0～5.0μg/kg范围内,方法回收率为71.3%～93.7%,相对标准偏差在3.7%～9.7%之间。该方法灵敏度高、重现性好,适用于猪肉样品中痕量玉米赤霉醇类药物残留的测定。     

Efficient white emitting copolymers based on bipolar fluorene-co-dibenzothiophene-S,S-dioxide-co-carbazole backbone

Efficient white light emitting polymers were synthesized based on poly(9,9-dioctylfluorene-co-dibenzothiophene-S,S-dioxide) as blue emitter and a bisphenylamine functionalized 2,1,3-benzothiadiazole (DPABT) as red emitter. It was found that the incorporation of hole-transporting carbazole moiety into polymer main chain could effectively reduce the hole injection barriers, which can lead to distinctly improved charge balance in the emissive layer. Additionally, the hole-transporting carbazole units may form efficient bipolar host with electron-transporting dibenzothiophene-S,S-dioxide units. The white light emitting diodes based on single polymer PFSOCzDPABT showed the maximum luminous efficiency of 3.3 cd/A with the maximum luminance of 10282 cd/m2 , and the luminous efficiency showed only 24% roll off at current density of 400 mA/cm2 . These Commission Internationale d’Enclairage (CIE) coordinates of the devices changed slightly with the driving voltages increasing from 8 V to 12 V, and were very close to National Television System Committee (NTSC) standard white light emission of (0.33, 0.33). The results indicated that the incorporating bipolar host and low band gap DPABT unit was a promising way to achieve efficient single white light emitting copolymers.     

Effect of nanocrystalline cellulose on the curing characteristics and aging resistance properties of carbon black reinforced natural rubber

This work focused on the effect of nanocrystalline cellulose (NCC) on the curing characteristics, aging resistance and thermal stability of natural rubber (NR) reinforced with carbon black (CB). Sharing the same fillers loading of 45 parts per hundred rubber (phr), NR/NCC/CB composites with different NCC/CB ratios (i.e. 0/45, 5/40, 10/35, 15/30, 20/25 phr) were prepared and analyzed. Resorcinol and hexamethylene tetramine (RH), acting as the modifier in NR/NCC interface, was also discussed for its influence. The result showed that an relatively higher ratio of NCC/CB led to a lower torque, a shorter cure time (T ₉₀), a slightly longer scorch time (T ₁₀) and a bigger vulcanization rate constant (K). This tendency suggested that the existence of NCC accelerated the vulcanization process. Additionally, modified by RH, NR/NCC/CB compounds exhibited a short T ₁₀ and a elevated torque. And a moderate RH content would lower the E _a of vulcanization. A 10 phr substitute of CB by NCC can help to improve aging resistance in terms of mechanical properties. In a high temperature aging condition, composites with 10 phr NCC also performed the highest storage modulus (G′) among composites tested. A moderate NCC content contributed to the best retention of G′ after high temperature aging, so did the incorporation of RH. With the partial replacement of CB by NCC, the temperature of 5% weight-lose had a slight drop and the apparent crosslink density showed a decrease. Thanks to the interaction of RH with both NR and NCC, composites showed an improvement in apparent crosslink density after modified by RH.     

Synthesis and Crystal Structure of （E）-2-phenyl-6,7dihydrobenzofuran-4（5H）-one O-cyanomethyl Oxime

A pair of E/Z-isomers of 2-phenyl-6,7-dihydrobenzofuran-4（5H）-one O-cyanomethyl oxime,C16H14N2O2,as potential drugs for treating peptic ulcer and other acid-related diseases have been synthesized and characterized by IR,MS and NMR spectra.Meanwhile,the crystal of IIIa was obtained and determined by X-ray single-crystal diffraction.Crystal data： monoclinic system,space group P21 /c,a = 8.423（8）,b = 19.596（16）,c = 8.770（8）,β = 107.750（12）°,V = 1379（2）3,Z = 4,F（000） = 560,Dc = 1.283 g/cm3,μ = 0.086 mm 1,R = 0.0681 and wR = 0.2029 for 14472 independent reflections（Rint = 0.0782） and 2428 observed ones（I 2σ（I））.