Design and Fabrication of Composite Smart Structures with High Electric and Mechanical Performances for Future Mobile Communication

In this paper, we have developed a load-bearing outer skin for antennas, which is termed a composite smart structure (CSS). The CSS is a multilayer composite sandwich structure in which antenna layers are inserted. A direct-feed stacked patch antenna is considered. A design procedure including the structure design, material selection, and design of antenna elements in order to obtain high electric and mechanical performances is presented. An optimized honeycomb thickness is selected for efficient radiation and impedance characteristics. High gain conditions can be obtained by placing the outer facesheet in the resonance position, which is at about a half wavelength distance from the ground plane. The measured electrical performances show that the CSS has a great bandwidth (over 10%) and a higher gain than an antenna without a facesheet and has excellent mechanical performances, owing to the composite laminates and honeycomb cores. The CSS concept can be extended to give a useful guide for manufacturers of structural body panels and for antenna designers.     

Crystallographic report: Bis(norfloxacin)dilead(II) tetranitrate, [Pb2(H‐Norf)2(ONO2)4]

The centrosymmetric binuclear structure of [Pb₂(H‐Norf)₂(ONO₂)₄]shows the geometry around each lead(II) atom to be distorted trigonal bipyramidal with Pb–O distances ranging from 2.357(3) to 2.769(4) Å. Copyright © 2003 John Wiley & Sons, Ltd.     

Surface modifications of ITO electrodes for polymer light-emitting devices

Surface modifications were performed on the indium tin oxide (ITO) substrates for polymer light-emitting devices, using the different treatment methods including solvent cleaning, hydrochloric acid treatment and oxygen plasma. The influence of modifications on the surface properties of ITO electrodes were investigated by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), contact angle, and four-point probe. The surface energies of the ITO substrates were also calculated from the measured contact angles. Experimental results demonstrate that the surface properties of the ITO substrates strongly depend on the modification methods, and oxygen plasma more effectively improves the ITO surface properties compared with the other treatments. Furthermore, the polymer light-emitting electrochemical cells (LECs) with the differently treated ITO substrates as device electrodes were fabricated and characterized. It is observed that the surface modifications on ITO electrodes have a certain degree of influence upon the injection current, luminance and efficiency, but hardly upon the turn-on voltages of current injection and light emission which are close to the measured energy gap of electroluminescent polymer. Oxygen plasma treatment on the ITO electrode yields the better performance of the LECs, due to the improvement of interface formation and electrical contact of the ITO electrode with the polymer blend in the LECs.     

半群K(n,r)中的幂等生成元

设Singn是由一个n元集上的所有奇异变换所构成的奇异变换半群，I是由Singn中一些亏数为1的幂等元组成的集合，Howie利用有向图证明了：I是Singn的一个生成集当且仅当与其相应的有向图D（I）是强连通的完全图，本文利用多重有向图将这一结果推广到Singn的每个理想K（,r)上。     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

Synthesis of MgAl2O4 Spinel Nanometer Powder via Biology Polysaccharide Assisted Sol-Gel Process

A novel and cost-effective sol-gel process for preparation of MgAl₂O₄ spinel nanometer powders has been developed in this study. A solution of magnesium and aluminum nitrates in stoichiometric proportion was successfully embraced in the biology polysaccharide gel network, formed by the synergistic interaction between xanthan gum (XG) and locust bean gum (LBG) utilizing their broad-spectrum stability of salt tolerance and character of transformation from sol to gel on the condition of proper temperature and relative proportion of polymeric components. Dry gel could be obtained by vacuum dehydration of aqueous gel at low temperatures. Monolithic MgAl₂O₄ spinel nanometer powders were produced by calcining the dry gel above 800°C, with average crystallite size of 20 nanometers.     

Enhancement of Overall Photovoltaic Efficiency by Changing the Position of the Attaching Group -RSO3- on the Hemicyanine Dye Molecules

A new photoresponsive D-π-A dye, mPS, has been designed and synthesized.Compared to the parent dye PS, IPCE values in the region from 400 nm to 560 nm was greatly improved upon changing the attaching group from the p- position to the o- position of the π-conjugation bridge. A solar cell based on mPS generated a remarkably high overall yield η of 5.4% under irradiation of 80.0 mW cm^-2 white light from a Xe lamp, Compared with PS, the overall yield η increased by 64%.