One-pot synthesis of uniform hollow cuprous oxide spheres fabricated by single-crystalline particles via a simple solvothermal route

Uniform Cu₂O hollow spheres fabricated by single-crystalline particles (smaller than 20 nm) are facile synthesized in ethylene glycol (EG) solution by a simple solvothermal route without using pre-fabricated templates and reductive agents. EG in this protocol is not only used as a solvent, complexing agent, and reducing agent, but also served as a structure-directing agent for the formation of hollow structure. By control of reaction conditions, such as reaction time, temperature, and the anions, the morphology and structure of the hollow spheres can be tuned. A coordination adsorption and oriented attachment and Ostwald ripening mechanism is proposed for explaining the formation process of hollow Cu₂O spheres in EG solution; and importantly, the hollow Cu₂O spheres exhibit an excellent property for the electro-catalytic oxidization of ascorbic acid in acetic acid buffer solution. Moreover, the hollow spherical Cu₂O particles could be potentially applied in catalysis, sensor, and as model for fundamental research.     

体结构GaAs光导开关实验研究

为解决光导开关耐受场强的提高问题,研制了2种体结构光导开关,并进行了实验研究。两种开关均由半绝缘GaAs材料制成,一种尺寸为10.0 mm×10.0 mm×0.6 mm,电极位于10.0 mm×10.0 mm面上相对位置,电极直径6 mm;另一种尺寸为15.0 mm×15.0 mm×3.0 mm,8 mm直径电极位于15.0 mm×15.0 mm面上相对位置。测试了第1种开关在不同半高宽脉冲加载电压下的击穿电压,结果表明其最大耐受电压达7.6 kV,击穿电场127 kV/cm。对第2种结构测试了开关在直流加载条件下的暗态伏安特性并进行了触发实验,结果表明在15 kV工作电压下,其放电最大电流超过3.5 kA。     

非匹配负载对宽带脉冲产生器谐振特性的影响

 宽带脉冲产生器的谐振特性决定了产生电磁脉冲的频谱,分析了带耦合器的同轴1/4波长谐振器在负载为非完全匹配天线时,天线反射对谐振特性的影响。通过建立级联二端口微波网络分析模型,将非匹配负载的反射系数计入等效耦合器反射系数中,得到了输出脉冲及辐射场频谱与负载反射系数的关系式。数值模拟了包括谐振器、耦合器和天线在内的整个宽带脉冲辐射系统,得到的辐射场频谱与理论预期相符。由于负载反射的影响,在中心频率两侧产生了两个副峰,在高功率实验中也观察到了该现象。     

Sr0.6Ba0.2Ca0.2Al2O4 ∶Eu,Dy的制备与长余辉发光性能研究

采用高温固相法制备了Ca,Ba共掺的Sr_0.6Ba_0.2Ca_0.2Al₂O₄ ∶Eu²⁺_0.01, Dy³⁺_0.02和单掺Ba的Sr_0.6Ba_0.4Al₂O₄ ∶Eu²⁺_0.01, 关键词： 长余辉 铝酸锶 稀土掺杂 陷阱能级     

Characteristics of cobalt-based alloy coating on tool steel prepared by powder feeding laser cladding

Co-based alloy coating was deposited on tool steel by powder feeding laser cladding. Sections of such coatings were examined to reveal their microstructures and phases using scanning electron microscope (SEM) and X-ray diffractometer (XRD). The results showed that the prime phase (γ-Co dendrite) and other phases, including Cr₂₃C₆, Co₇W₆, and CrNi existed in the coatings. Some different solidification morphologies, such as planar (at the interface), cellular and dendrite formed, varying from the interface to the surface. Fine microstructures of γ-Co dendrite and lamellar eutectic in dendritical regions strengthened the coatings. Besides, the effects of aged treatment on the microstructure and microhardness of the surface coating were studied. Aged treatment led to the precipitations of some carbide particles (Cr₇C₃ and Co₃C) and boride particles (Co₄B) from the cladded coating, causing an increase in microhardness in the laser-cladded coating.     

Modification of bonding properties and microstructure of resin-cement interface by coupling agents

To solve the problem of organic-inorganic light conductive composite interface features, transparent resin and cement matrix were used as carriers to further study features of the organic-inorganic interface formed by transparent resin and cement matrix and the interface modification of the coupling agent. The bond strength, micro-hardness, microstructure and surface morphology of a resin light conductive cementitious materials (RLCCM) interface were evaluated by tests of tensile and oblique shear, micro-hardness, environmental scanning electron microscopy, and atomic force microscope. The results show that the silane A-151 and aluminate coupling agent could significantly improve interface bond properties of RLCCM. At 7 d, the interface tensile bond strength of the silane A-151 and aluminate coupling agent increased by 117 and 105%, respectively. At 28 d, strength on average increased by 73%. At 7 d, interface shear strength the silane A-151 and aluminate coupling agent of 45° increased by 43 and 53%, respectively, At 28 d, strength on average increased by 40%. The transparent resin performance weakened region thickness up to 100 μm; the hardness of the transparent resin in the transition region was increased by 19.6 and 39.9%, respectively. Silane coupling agent A-151 and cement hydration products formed flat spherical particles with diameter of approximately 78 nm, and these particles mosaicked and fused in the surface of the hydrate; therefore, the surface became denser and smoother.     

二维缺陷GaAs电子结构和光学性质第一性原理研究

采用基于密度泛函理论的第一性原理方法计算了存在Ga空位缺陷和掺杂B原子的二维GaAs的能带结构、态密度和光学性质.计算结果表明空位缺陷二维GaAs显示出金属特性,B原子的引入使体系变为间接带隙半导体,禁带宽度为0.35 eV.态密度计算发现体系低能带主要由Ga的s态、p态、d态和As的s态、p态构成;高能带主要由Ga和As的s态、p态构成.掺杂B原子与存在空位缺陷的二维GaAs相比,静态介电常数相对较低,变为8.42,且易于吸收紫外光,在3.90～8.63 eV能量范围具有金属反射特性,反射率达到52%.     

三氧化钨/氧化银复合材料的水热法合成及其光催化降解性能研究

染料污染是水污染中最严重的问题之一,吸引了很多科学家的关注.人们尝试了很多方法去解决该问题,如化学氧化法、物理吸附法、光催化降解法和生物降解法等.与其他几种方法相比,光催化法有着低能耗、环保以及高效等优势.三氧化钨是常见的半导体材料,具有独特的光学性能,近年来受到了广泛的研究.本文以钨酸钠和硫脲为前驱体,通过水热法制备了三氧化钨/氧化银(WO_3/Ag_2O)复合材料,并用光催化降解亚甲基蓝来分析其光催化性能.通过X射线光电子能谱、X射线衍射、透射电子显微镜、扫描电子显微镜、紫外可见吸收光谱等表征手段对样品的形貌、晶格结构和光催化的性能进行表征.氧化银的带宽为1.2 e V,对可见光很敏感,三氧化钨和氧化银的复合使材料在可见光下的光催化活性显著增强,在可见光下对亚甲基蓝染料的光降解率可以达到98%.实验结果表明,复合材料中的三氧化钨纳米棒为六方相,其平均直径约为200 nm,平均长度约为4μm.而复合材料中的氧化银纳米颗粒为六方相,附着在氧化钨纳米棒的表面,平均晶粒尺寸为20 nm.氧化银的存在为复合材料提供了更多的反应活性位点.相较于单一组分,复合材料在可见光下的光吸收度更高,这说明三氧化钨和氧化银的复合改变了材料的能带结构.研究发现,三氧化钨和氧化银之间形成的异质结构是其优良光催化性能的来源.此外,三氧化钨和氧化银复合材料还具有良好的催化稳定性和化学稳定性.本文结果表明,可以通过给宽带隙的半导体材料复合一些带隙合适的金属氧化物以提升其光催化活性.     

铀在Nd_2Zr_2O_7烧绿石中的固溶量及重离子辐照效应

Nd_2Zr_2O_7烧绿石因其稳定的物理化学性质和辐照稳定性可以作为高放废物中锕系核素的固化基材.通过溶胶凝胶—喷雾热解—高温烧结方法制备了含铀的Nd_2Zr_2O_7烧绿石固化体;开展了Nd_2Zr_2O_7和Nd_(1.9)U_(0.1)Zr_2O_7固化体的重离子辐照实验,辐照剂量为1 dpa和3 dpa;利用X射线衍射和Raman光谱对固化体结构进行了分析.研究发现铀在Nd_2Zr_2O_7烧绿石体系的固溶量仅为10 at%,高价态铀掺杂导致固化体结构向无序化转变.重离子辐照实验表明, Nd_2Zr_2O_7烧绿石基材具有较高的抗辐照稳定性;而Nd_(1.9)U_(0.1)Zr_2O_7在较低辐照剂量下,固化体烧绿石体系结构破坏,重离子辐照诱导固化体结构转变为更加无序化的萤石结构.低固溶量和抗辐照能力减弱主要是由于锕系核素烧绿石固化体的结构无序化所致.     

Pair-produced heavy particle topologies: MSSM neutralino properties at the LHC from gluino/squark cascade decays

Processes of the form pp → anything → X_iX_j → + + notE are studied via a technique that may be viewed as an adaptation of time-honoured Dalitz plot analyses. X_i and X_j are new heavy states (with i, j =1, . . .,n), which may be identical or distinct; and and are necessarily distinct standard model (SM) fermion pairs whose invariant masses can be measured. A Dalitz-like plot of said invariant masses, versus , exhibits a topology connected to the masses and specific decay chains of X_i and X_j. Aside from relatively minor details, observed patterns consist of a collection of box and wedge shapes. This collection is model-dependent: comparison of the observed pattern to the possibilities for a specific model yields information on which new particle pair combinations are actually being produced, information beyond that extractable from conventional one-dimensional invariant mass distributions. The technique is illustrated via application to the minimal supersymmetric standard model (MSSM) process pp → → e⁺e^- + μ⁺μ^- notE. Here the heavy states are neutralinos (i = 2,3,4) - note that is excluded - which are produced in gluino/squark ( / ) cascade decay chains. Even with fairly modest expectations for the LHC performance during the first few years, this method still provides substantial insight into the neutralino mass spectrum and couplings if gluino/squark masses are relatively low (≃ 400 GeV). Arrival of the final proofs: 29 November 2005