A Noninvasive, on Wafer Method to Determine the Intrinsic Stress of a Polymer Layer

The method described in this paper allows an investigator to determine the intrinsic stress of a polymer layer in a way that does not result in damage to devices or test structures. The method requires that a small area of the polymer be released from the substrate to form a diaphragm. The diaphragm is stimulated with acoustic white noise and the diaphragm movement is monitored with a laser vibrometer. The first few resonance frequencies of the diaphragm are obtained using a laser vibrometer and then those frequencies are used to calculate the membrane intrinsic bi-axial tension.     

GaAsN/AlAs/AlGaAs double barrier quantum wells grown by molecular beam epitaxy as an alternative to infrared absorption below 4 μm

In this work, we report on the design, growth and characterization of GaAsN/AlAs/AlGaAs double barrier quantum well infrared detectors to achieve intraband absorption below 4 μm. Due to the high effective mass of N-dilute alloys, it is common for these N-containing double barrier quantum well structures to have more than one bound state within the quantum well, enabling the possibility of achieving multispectral absorption from these confined levels to the quasi-bound. Based on a transfer matrix calculation we will study the influence of the potential parameters, in particular the well width and the introduction of a GaAs spacer layer in between the N-well and the AlAs barriers. We will compare the case in which there are two confined levels with the case in which only one level is bound, like in the conventional AlGaAs/AlAs/GaAs structures. On the basis of the simulation, we have grown and characterized some N-containing double barrier detectors. Moreover, an optimization of the post-growth annealing treatments of the GaAsN quantum well structures has also been performed. Finally, room temperature absorption measurements of both as-grown and annealed samples are presented and analyzed.     

Projection of Markov Measures May Be Gibbsian

We study the induced measure obtained from a 1-step Markov measure, supported by a topological Markov chain, after the mapping of the original alphabet onto another one. We give sufficient conditions for the induced measure to be a Gibbs measure (in the sense of Bowen) when the factor system is again a topological Markov chain. This amounts to constructing, when it does exist, the induced potential and proving its Hölder continuity. This is achieved through a matrix method. We provide examples and counterexamples to illustrate our results.     

<Emphasis Type="Italic">J/Ψ</Emphasis>production

For more than 25 yearsJΨ production has helped to sharpen our understanding of QCD. In proton induced reaction some observations are rather well understood while others are still unclear. The current status of the theory ofJΨ production will be sketched, paying special attention to the issues of formation time andJΨ re-interaction in a nuclear medium.     

On the average complexity of 3D-Voronoi diagrams of random points on convex polytopes

It is well known that the complexity, i.e. the number of vertices, edges and faces, of the 3-dimensional Voronoi diagram of n points can be as bad as Θ(n²). It is also known that if the points are chosen Independently Identically Distributed uniformly from a 3-dimensional region such as a cube or sphere, then the expected complexity falls to O(n). In this paper we introduce the problem of analyzing what occurs if the points are chosen from a 2-dimensional region in 3-dimensional space. As an example, we examine the situation when the points are drawn from a Poisson distribution with rate n on the surface of a convex polytope. We prove that, in this case, the expected complexity of the resulting Voronoi diagram is O(n).     

Electron–hole complexes in self-assembled quantum dots in strong magnetic fields

We present results of calculations and experiments on electron–hole complexes in InGaAs/GaAs self-assembled quantum dots in high magnetic field (B). Due to hidden symmetries, the chemical potential of an N-exciton system at special B fields becomes insensitive to the exciton number as well as the magnetic field. This results in plateau regions of high intensity in measured magneto-PL spectrum. Theoretical calculations using exact diagonalization techniques successfully explain the measured magneto-photoluminescence spectrum with B fields up to 28 T.     

Conformational analysis of dipeptide‐derived polyisocyanides

The conformational properties of polymers derived from isocyanodipeptides have been investigated with a combination of model calculations, X‐ray diffraction, and circular dichroism spectroscopy. Depending on the configuration of the side chains, defined arrays of hydrogen bonds along the polymeric backbone are formed. This leads to a well‐defined conformation as, for example, expressed in the formation of lyotropic liquid‐crystalline phases and increased helical stability. Upon the disruption of the hydrogen bonds by a strong acid, a less well‐defined macromolecular conformation is observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1725–1736, 2003     

On additives, morphological evolution and dielectric breakdown in low density polyethylene

A series of low density polyethylene systems has been studied with respect to structural evolution and short-term dielectric breakdown behaviour. All materials were based upon a single polymer, that is commonly used in high voltage applications, but with different additives. In all three of these systems, multiple melting transitions were observed, as a result of molecular fractionation effects during crystallization. In the virgin polymer, a space-filling banded spherulitic morphology was found to develop at low temperatures (102 °C and below) whereas, at higher temperatures, only a few isolated axialites were observed. Inclusion of the antioxidant resulted in greatly increased nucleation densities, such that, at low temperatures, no evidence of spherulitic organisation remained. At higher temperatures, sheaf-like lamellar aggregates developed, which were much smaller and much more numerous than in the case of the virgin polymer. Further addition of dicumyl peroxide (DCP) resulted in the rapid formation of a crosslinked network at 200 °C. Some crosslinking also occurred at 150 °C, but over a much longer timescale. Where extensive crosslinking occurred prior to crystallization, the resulting gel inhibited structural development, such that only a few small, isolated sheaves were able to form at 102 °C. In view of the principal application area of this material, the breakdown strength of each of the above systems was then measured and the whole data set was analysed statistically. When structural factors were considered alongside the statistics, no clear trends emerged to indicate that either the compositional or morphological variations were reflected in the short-term electrical failure processes.     

Effects of B′-site transition metal on the properties of double perovskites Sr2FeMO6 (M=Mo, W): B′ 4d-5d system

The crystal structure, magnetic and magnetotransport properties of the variation of B′-site transition metal in Sr₂FeMO₆ (M=Mo, W) with double perovskites structure have been investigated systematically. Measurements of magnetization vs. temperature at H=5 T show that Sr₂FeMoO₆ is a ferromagnet and Sr₂FeWO₆ is an antiferromagnet with T_N∼35 K. Additionally, the large magnetoresistance ratio (MR) of ∼22% (H=3 T) at room temperature (RT) was observed in the Sr₂FeWO₆ compound. However, the Sr₂FeMoO₆ compound did not show any significant MR even at high fields and RT (MR∼1%; H=3 T and 300 K). The implications of these findings are supported by band structure calculations to explain the interaction between the 4d(Mo) and 5d(W) orbitals of transition metal ions and oxygen ions.