Γ andX bandgap hydrostatic deformation potentials for epitaxial In0.52Al0.48As on InP(001)

The pressure dependence of the direct and indirect bandgap of epitaxial In_0.52Al_0.48As on InP(001) substrate has been measured using photoluminescence up to 92 kbar hydrostatic pressure. The bandgap changes from Γ toX at an applied pressure of ∼ 43 kbar. Hydrostatic deformation potentials for both the Γ andX bandgaps are deduced, after correcting for the elastic constant (bulk modulus) mismatch between the epilayer and the substrate. For the epilayer we obtain and+(2.81±0.15)eV for the Γ andX bandgaps respectively. From the pressure dependence of the normalized Γ-bandgap photoluminescence intensity a Γ-X lifetime ratio, (τ_Γ/τ _X ), of 4.1×10⁻³ is deduced.     

Removal of nanoparticles on silicon wafer using a self-channeled plasma filament

The effective removal of nanoparticles from a silicon wafer surface was demonstrated using the self-channeled plasma filament excited by a femtosecond (130?fs) Ti:sapphire laser (?? _p=790?nm). The photoinduced self-channeled plasma filament in air reached a length of approximately 110?C130?mm from the first focal spot with diameters ranging from 40 to 50???m at input intensities of more than 1.0×10¹⁴?W/cm². By the scan of wafer using the X?CY?CZ stage during self-channeled plasma filament, the removal variation of nanoparticles on surface was observed in situ before and after the plasma filament occurred. The cleaning efficiency was strongly dependent on the gap distance between the plasma filament and the surface. The removal efficiency of nanoparticles reached 96?% with no damage to the surface when the gap was 150???m.     

Investigation of scattering of elastic waves by cylinders in 1-3 piezocomposites

The scattering behavior of P-waves in piezoelectric composites with 1–3 connectivity is studied. The method of wave function expansion is adopted for the theoretical derivations. Analytical expressions are obtained for the distributions of mechanical displacement in z-direction along the circumferences of piezoelectric cylinders. These solutions are used to study the influence of each element of the stiffness matrix and the piezoelectric matrix on the various resonant modes of vibration. Numerical results obtained indicate that perturbations of the elements c₄₄ and e₁₅ significantly affect resonant frequencies and amplitudes, perturbations of c₁₁ and c₁₂ have pronounced effects on resonant modes of high frequencies also. However, the resonant modes are not so sensitive to the perturbations of c₁₃, e₃₁ and e₃₃. The dynamic characteristics of 1–3 connectivity piezoelectric composites exposed here are meaningful for the design and manufacture of sensor/actuator elements by this kind of composites as well as the on-line health monitoring of the mechanical properties variations of the composites itself.     

Evidence for muon neutrino oscillation in an accelerator-based experiment

We present results for nu(mu) oscillation in the KEK to Kamioka (K2K) long-baseline neutrino oscillation experiment. K2K uses an accelerator-produced nu(mu) beam with a mean energy of 1.3 GeV directed at the Super-Kamiokande detector. We observed the energy-dependent disappearance of nu(mu), which we presume have oscillated to nu(tau). The probability that we would observe these results if there is no neutrino oscillation is 0.0050% (4.0 sigma).     

Structural and electrical characterization of PZT on gold for micromachined piezoelectric membranes

Piezoelectric membranes have been fabricated that incorporate a gold bottom electrode with an adhesion layer of titanium–tungsten (10:90 wt. %). For solution-deposited acetic acid based lead zirconate titanate (HoAc-PZT) with a Zr:Ti ratio of 40:60, the film’s average piezoelectric coefficient, e₃₁, is -5.31 C/m², with a dielectric constant of 814 at 200 Hz, which is similar to values for platinum bottom electrodes. The PZT structure remains columnar on both types of bottom electrodes. Initial fabrication attempts resulted in cracking that initiated in the PZT layer of the structure. X-ray photoelectron spectroscopy was utilized to establish how processing affects diffusion throughout the composite membrane structure. Crack-free membranes were fabricated and tested. This paper discusses the performance properties and piezoelectric fatigue results for these membranes. PACS 77.84.-s; 77.84.Lf     

Activation volumes of wall-motion and nucleation processes in Co-based ferromagnetic multilayer films

Activation volumes of the wall-motion and nucleation processes in Co-based multilayer films were characterized from time-resolved domain evolution patterns. These activation volumes were both sensitive to the multilayer structure as well as the film preparation condition. The two activation volumes were generally unequal with each other and the inequality directly influenced on magnetization reversal behavior.     

Photovoltaic performance of flexible Cu(In,Ga)Se2 thin-film solar cells with varying Cr impurity barrier thickness

We report the effect of Cr impurity barrier on Cu(In,Ga)Se₂ (CIGS) thin-film solar cells prepared on flexible substrates. The Cr films with varying the thickness (t_Cr) were deposited on stainless steel substrates using direct-current magnetron sputtering. The solar cell performance was improved by increasing t_Cr since the diffusion of Fe impurities from the substrate to CIGS was suppressed. Although the elemental composition, grain size, and strain of CIGS film showed little change with varying Fe content, the fill factor and the short-circuit current density increased as decreasing Fe. The Fe increased the series resistance, shunt paths, and saturation current density. The reduction of Fe caused a steeper bandgap grading in CIGS which enhances current collection due to higher electric fields in bulk CIGS. CIGS solar cells with 1000 nm-thick Cr barrier showed the best conversion efficiency of 9.05%.