Generation of picoliter droplets of liquid for electrospray ionization with piezoelectric inkjet

We report the association of inkjet and electrospray ionization MS to detect picoliter droplet, where the liquid volume and its position onto the tip can be precisely controlled to form ultrafine droplets for successive ionization of the analyte. Single rectangle pulse was applied to piezoelectric device on inkjet microchip for the ejection of each picoliter droplet, and it was controlled by a computer. The voltage and width of driving pulse for the inkjet were optimized to make reproducible ejection of the solvent with low viscosity. The volume of each droplet was about 600 pl, and a trigger of 10 droplets was selected as the best inlet mode taking relative standard derivation of the droplets into consideration. The target substrate used with high voltage to form ionization was graphite, after several attempts with some materials. High‐speed camera was used to capture the breaking‐up process of a droplet. The distance between the inkjet nozzle and the tip was set at 2 cm to avoid short circuit. The influences on the mass intensity of the diameter of the tip, the volume and the concentration of the sample were examined. The tip with a small diameter performed greater intensity, and the limit of detection decreased, whereas the small volume of liquid played high ionization efficiency. Linear regression in the range between 1 and 200 ppm for caffeine was conducted, where internal standard theobromine was used. Some real samples were also detected with the instrument. Copyright © 2013 John Wiley & Sons, Ltd.     

Planar chirality of twisted trans-azobenzene structure induced by chiral transfer from binaphthyls

The absolute configuration of a binaphthyl-azobenzene dyad 2b, which has a chiral axis and a chiral plane, was determined by comparing the experimental circular dichroism (CD) spectra with the theoretical CD spectra calculated by the time-dependent (TD)-DFT method. The CD signals of the trans-azobenzene moiety indicated that the two benzene rings of this moiety are twisted unidirectionally. It is suggested that these dyads with shorter linkers may be suitable for use as chiroptical switches.     

A diffusive sampling device for simultaneous determination of ozone and carbonyls

A new diffusive sampling method for the simultaneous determination of ozone and carbonyls in air has been developed. In this method, silica gel impregnated with a mixture of trans-1,2-bis(2-pyridyl)ethylene (2BPE) and 2,4-dinitrophenylhydrazine (DNPH) is used as the absorbent; further, a porous sintered polyethylene tube (PSP-diffusion filter), which acts as a diffusive membrane, and a small polypropylene syringe (PP-reservoir) for elution of the analytes from the absorbent are used. The carbonyls present in air react with DNPH in the absorbent to form hydrazone derivatives. Concurrently, ozone in the air reacts with 2BPE to form pyridine-2-aldehyde, which immediately reacts with DNPH to form a pyridine-2-aldehyde hydrazone derivative. All the hydrazones derived from airborne carbonyls, including pyridine-2-aldehyde (formed from ozone), are completely separated and analyzed by high-performance liquid chromatography. The sampling rates of ozone (44.6 mL min(-1)) and formaldehyde (72.0 mL min(-1)) are determined by comparison with the rates obtained in an active sampling method. The sampling rates of other carbonyl compounds are calculated from the respective molecular weights according to a rule based on Graham's law. The calculated sampling rates agree with the experimental values. The DSD-BPE/DNPH method is advantageous because it is simple and allows for the simultaneous analysis of ozone and carbonyls.     

Environmental transmission electron microscopy observations of the growth of carbon nanotubes under nanotube-nanotube and nanotube-substrate interactions

The growth process of carbon nanotubes (CNTs) under CNT-CNT and CNT-substrate interactions has been observed directly by environmental transmission electron microscopy. Even a free standing CNT occasionally swings during the growth until it touches the substrate. In addition, we show that the growth direction of CNTs changes due to the interaction between CNTs.     

Cationic β-Scission of C−H and C−C Bonds for Selective Dimerization and Subsequent Sulfur-Free RAFT Polymerization of α-Methylstyrene and Isobutylene

A series of exo-olefin compounds ((CH₃)₂C(PhY)−CH₂C(=CH₂)PhY) were prepared by selective cationic dimerization of α-methylstyrene (αMS) derivatives (CH₂=C(CH₃)PhY) with p-toluenesulfonic acid (TsOH) via β-C−H scission. They were subsequently used as reversible chain transfer agents for sulfur-free cationic RAFT polymerization of αMS via β-C−C scission in the presence of Lewis acid catalysts such as SnCl₄. In particular, exo-olefin compounds with electron-donating substituents, such as a 4-MeO group (Y) on the aromatic ring, worked as efficient cationic RAFT agents for αMS to produce poly(αMS) with controlled molecular weights and exo-olefin terminals. Other exo-olefin compounds (R−CH₂C(=CH₂)(4-MeOPh)) with various R groups were prepared by different methods to examine the effects of R groups on the cationic RAFT polymerization. A sulfur-free cationic RAFT polymerization also proceeded for isobutylene (IB) with the exo-olefin αMS dimer ((CH₃)₂C(Ph)−CH₂C(=CH₂)Ph). Furthermore, telechelic poly(IB) with exo-olefins at both terminals was obtained with a bifunctional RAFT agent containing two exo-olefins. Finally, block copolymers of αMS and methyl methacrylate (MMA) were prepared via mechanistic transformation from cationic to radical RAFT polymerization using exo-olefin terminals containing 4-MeOPh groups as common sulfur-free RAFT groups for both cationic and radical polymerizations.     

Designing a Peptide-modified Screen-printed Gold Electrode as a Sensor for the Human Monocytic Leukemia Cell Line

We designed a screen-printed gold electrode (SPGE) with a peptide to detect cancer cells. The ability to sense circulating tumor cells (CTCs) and monitor their movement in blood vessels is important for cancer diagnosis. Human monocytic leukemia cells were selected as a model of CTCs because of their origin. The cell-recognition and cell-sensing peptide moieties were EICADP and Y₄C. The SPGE was modified with the cell-recognition moieties of the CY₄EICADPY₄C in a bridge-type construction due to the cysteine residue at both terminals. The calibration curve was linear and ranged from 25 to 2,000 cells/mL with a LOD of 8 cells/mL.