Synthesis of β‐Methoxyacrylate Natural Products Based on Box‐PdII‐Catalyzed Intermolecular Methoxycarbonylation of Alkynoles

Bis(oxazoline)‐palladium(II) catalyzed carbonylation of homopropargyl alcohols afforded acyclic methoxyacrylate 2 and 6‐membered lactone 3a , 3b , 3d , 3e , 3f , 3g , 3h , 3i , 3j , 3k in good combined yield. In the case of propargyl alcohols, 5‐membered lactones 3p , 3q , 16 were obtained in moderate yields. The one‐pot synthesis of kawa lactones 3a , 3r , 3s and formal synthesis of dihydroxycystothiazole A and dihydroxycystothiazole C are presented. To elucidate the stereochemistry of (+)‐annularin G and (?)‐annularin H, the first asymmetric syntheses of these natural products were achieved.     

Evaluations of vertical resolution of conductive polymer three-dimensional microstructures photofabricated in transparent polymer sheet

Conductive polymer three-dimensional microstructures were photofabricated utilizing the two-photon absorption of a sensitizer dye. The resulting three-dimensional structures were excised from the transparent polymer sheet using a micro-manipulator. The processing precisions for the vertical direction of the conductive polymer three-dimensional microstructure obtained in the transparent polymer sheet were evaluated in the present study. As a result, for the configurations of the obtained polypyrrole line deposition, the line height/line width ratios were around 5: 1; this ratio is higher than that of other UV resin works (h: w 2:4–3: 1) and the cross section distortion is not negligible for maintaining the higher reproducibility of the photofabrication.     

A microfluidic chip integrated with a microoptical lens fabricated by femtosecond laser micromachining

We report on the integration of microlens and microfluidic channels in fused silica glass chip using femtosecond laser micromachining. The main process includes three procedures: (1) femtosecond laser scanning for forming a hemispherical surface and a Y-shaped channel in the fused silica glass; (2) chemical etching of the sample for removal of the modified areas; and (3) oxyhydrogen (OH) flame polish for smoothening the surface of the microlens. In addition, we demonstrate that the fabricated microlens exhibits good imaging performance with a 5× magnification, showing great potential in future lab-on-a-chip applications.     

The IR modulator utilizing light scattering effect with ferroelectric liquid crystal for gas analysis

Experimental infrared modulator elements have been fabricated utilizing the transient light scattering effect of ferroelectric liquid crystal with asymmetric waveform voltage drive. The new elements perform 80% modulation degrees at the 632.8nm. We have also achieved 30% modulation degrees in the 4 to 5µ m region where the strongest CO₂ absorption bands exist. A new type of analyzer which monitors ambient air quality has been developed. This analyzer uses non-dispersive infrared absorption method and composes of a double-beam, a single detector and a pair of liquid crystal light modulator as the IR chopper. The detection has achieved 10ppm noise equivalent concentration.     

Spatial resolution improvement of scanning microscopy based on thermal lens spectroscopy with a total-internal-reflection arrangement.

In scanning microscopy by total internal reflection with thermal lens spectroscopy, its spatial resolution depends on the distance between the sample and a converging lens, which corresponds to the objective lens in an ordinary optical microscope. It was found that the resolution was best when the signal induced by the thermal lens effect was maximum. The distance was precisely adjusted by monitoring the signal intensity, and the resolution became twice better than that previously reported. Using a shorter focal-length lens, a resolution of 1.9 microm was attained.     

Fabrication of microfluidic optical waveguides on glass chips with femtosecond laser pulses

We describe the fabrication of microfluidic channel structures on the surface of a borosilicate glass slide by femtosecond laser direct writing for optical waveguide application. Liquid with a variable refractive index is fed into the microchannel, serving as the core of the waveguide. We demonstrate that either a multimode or a single-mode waveguide can be achieved by controlling the refractive index of the liquid.