Simultaneous observation of CO isotopomer absorption by broadband difference-frequency generation using a direct-bonded quasi-phase-matched LiNbO3 waveguide

Rovibration absorption lines both of 12CO and 13CO are observed simultaneously with the output of a 2 microm broadband difference frequency generated in a direct-bonded quasi-phase-matched LiNbO3 waveguide, which is a 50 mm device with a single quasi-phase-matching period that is operated at a constant temperature. The wavelength conversion efficiency and the difference-frequency generation bandwidth reach 100%/W and 100 nm, respectively. The idler output bandwidth in the 2 microm region is obtained by group-velocity matching or phase-mismatch minimization when a 0.94 microm pump laser diode and a 1.55 microm tunable signal source are used.     

Strong resonance enhancement of a single harmonic generated in the extreme ultraviolet range

We report the demonstration of strong resonance enhancement of a single high-order harmonic in the extreme ultraviolet (XUV) region generated from the interaction of a femtosecond pulse with low-ionized In ablation. A strong 13th harmonic (61.2 nm) of Ti:sapphire laser radiation with output intensity almost two orders of magnitude higher than neighboring harmonics was observed in these studies. The high conversion efficiency of the 13th harmonic (8 x 10(-5)) is attributed to multiple collisions of electron trajectories with the origin due to multiphoton resonance with the In ion.     

Interrelation between inhomogeneity and cyclability in O3‐NaFe1/2Co1/2O2

O3‐NaFe_1/2Co_1/2O₂ shows initial capacity of 160 mAh/g and an average operating voltage of 3.1 V (vs. Na) with good cyclability, and is a promising candidate of the cathode materials for sodium‐ion secondary batteries (SIBs). Here, we found that the cyclability of the slowly‐cooled sample is much worse than that of quenched one, even though the former sample keeps the O3‐type structure. The energy dispersive X‐ray spectroscopy (EDX) images suggest that the slow‐cooled sample (Na_x Fe_1–yCo_y O₂) is inhomogeneous in the Fe concentration (1 – y), perhaps triggered by the Na deficiency (1 – x). We ascribed the poor cyclability in the slowly‐cooled sample to the concentration inhomogeneity (Δy). The Δy is further responsible for the fluctuation of the lattice constants (a and c), as revealed by the Williamson–Hall plot. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Quarkonia at Finite T: An Approach Based On QCD Sum Rules and the Maximum Entropy Method

Quarkonium spectral functions at finite temperature are studied, making use of a recently developed method of analyzing QCD sum rules by the maximum entropy method. This approach enables us to directly obtain the spectral function from the sum rules, without having to introduce any specific assumption about its functional form. QCD sum rules for heavy quarkonia incorporate finite temperature effects in form of changing values of the various gluonic condensates that appear in the operator product expansion. These changes depend on the energy density and pressure at finite temperature, which we extract from quenched lattice QCD calculations. As a result, it is found that the charmonium ground states of both S-wave and P-wave channels dissolve into the continuum already at temperatures around or slightly above the critical temperature T _c , while the bottomonium states are less influenced by temperature effects, surviving up to about 2.5 T _c or higher for S-wave and about 2.0 T _c for P-wave states.     

Controlling the orientation of polar molecules with combined electrostatic and pulsed,nonresonant laser fields

We demonstrate that molecules with a moderate permanent dipole moment can be oriented with combined electrostatic and pulsed, nonresonant laser fields. We use OCS molecules as a sample. The degree of orientation can be increased by increasing the magnitude of electrostatic field and the peak intensity of the laser field or by decreasing the rotational temperature of the molecules.     

Sliding acceleration of water droplets on a surface coated with fluoroalkylsilane and octadecyltrimethoxysilane

Both fluoroalkylsilane (FAS) and octadecyltrimethoxysilane (ODS) were coated on oxidized silicon wafers using soaking and CVD method. Smooth coatings with Ra values of less than 1 nm were attained. The slope of the sliding acceleration against the inverse of the droplet mass showed an inflection point. That point shifted to the direction of smaller droplets with decreasing FAS ratio to ODS. The water droplets’ length was increased when the sliding velocity was increased. Fluoroalkylsilane addition to ODS increases the interaction between water and the hydrophobic surface. Results showed that the sliding acceleration of a water droplet depends strongly on the surface ratio of these silanes.     

Dynamic hydrophobicity of water droplets on the line-patterned hydrophobic surfaces

Static and dynamic hydrophobicities of water droplet on a patterned surface prepared using fluoroalkylsilanes with different molecular chain lengths were investigated. Contact angles on the patterned surfaces well agreed with values predicted using Cassie’s theory. On the same line width ratio, total retention force was governed by the fluoroalkylsilane with slow-sliding acceleration. The total retention force decreased with the decreasing width ratio of silane with slow-sliding acceleration on the surface. These results imply that the sliding acceleration of water droplets on a hydrophobic surface depends both on chemical composition and patterning structure.     

The chemisorption of pentacene on Si(0 0 1)-2 × 1

Adsorption structures of the pentacene (C₂₂H₁₄) molecule on the clean Si(0 0 1)-2 × 1 surface were investigated by scanning tunneling microscopy (STM) in conjunction with density functional theory calculations and STM image simulations. The pentacene molecules were found to adsorb on four major sites and four minor sites. The adsorption structures of the pentacene molecules at the four major sites were determined by comparison between the experimental and the simulated STM images. Three out of the four theoretically identified adsorption structures are different from the previously proposed adsorption structures. They involve six to eight Si-C covalent chemical bonds. The adsorption energies of the major four structures are calculated to be in the range 67-128 kcal/mol. It was also found that the pentacene molecule hardly hopped on the surface when applying pulse bias voltages on the molecule, but was mostly decomposed.     

Slow positron beam study of corrosion-related defects in pure iron

Corrosion-related defects of pure iron were investigated by measuring Doppler broadening energy spectra (DBES) of positron annihilation and positron annihilation lifetime (PAL). Defect profiles of the S-parameter from DBES as a function of positron incident energy up to 30 keV (i.e. ∼1 μm depth) were analyzed. The DBES data show that S-parameter increases as a function of positron incident energy (mean depth) after corrosion, and the increase in the S-parameter is larger near the surface than in the bulk due to corrosion. Furthermore, information on defect size from PAL data as a function of positron incident energy up to 10 keV (i.e. ∼0.2 μm depth) was analyzed. In the two-state trapping model, the lifetime τ₂ = 500 ps is ascribed to annihilation of positrons in voids with a size of the order of nanometer. τ₁, which decreases with depth from the surface to the bulk, is ascribed to the annihilation of positrons in dislocations and three-dimensional vacancy clusters. The corroded samples show a significant increase in τ₁ and the intensity I₂, and near the surface the corroded iron introduces both voids and large-size three-dimensional vacancy clusters. The size of vacancy clusters decreases with depth.