Electrospinning of ultrafine cellulose acetate fibers: Studies of a new solvent system and deacetylation of ultrafine cellulose acetate fibers

Electrospinning of cellulose acetate (CA) in a new solvent system and the deacetylation of the resulting ultrafine CA fibers were investigated. Ultrafine CA fibers (∼2.3 μm) were successfully prepared via electrospinning of CA in a mixed solvent of acetone/water at water contents of 10–15 wt %, and more ultrafine CA fibers (0.46 μm) were produced under basic pH conditions. Ultrafine cellulose fibers were regenerated from the homogeneous deacetylation of ultrafine CA fibers in KOH/ethanol. It was very rapid and completed within 20 min. The crystal structure, thermal properties, and morphology of ultrafine CA fibers were changed according to the degree of deacetylation, finally to those of pure cellulose, but the nonwoven fibrous mat structure was maintained. The activation energy for the deacetylation of ultrafine CA fibers was 10.3 kcal/mol. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 5–11, 2004     

Desorption behavior of a surfactant in a linear low‐density polyethylene blend at elevated temperatures

The desorption behavior of a surfactant in a linear low‐density polyethylene (LLDPE) blend at elevated temperatures of 50, 70, and 80 °C was studied with Fourier transform infrared spectroscopy. The composition of the LLDPE blend was 70:30 LLDPE/low‐density polyethylene. Three different specimens (II, III, and IV) were prepared with various compositions of a small molecular penetrant, sorbitan palmitate (SPAN‐40), and a migration controller, poly(ethylene acrylic acid) (EAA), in the LLDPE blend. The calculated diffusion coefficient (D) of SPAN‐40 in specimens II, III, and IV, between 50 and 80 °C, varied from 1.74 × 10^?11 to 6.79 × 10^?11 cm²/s, from 1.10 × 10^?11 to 5.75 × 10^?11 cm²/s, and from 0.58 × 10^?11 to 4.75 × 10^?11 cm²/s, respectively. In addition, the calculated activation energies (E_D) of specimens II, III, and IV, from the plotting of ln D versus 1/T between 50 and 80 °C, were 42.9, 52.7, and 65.6 kJ/mol, respectively. These values were different from those obtained between 25 and 50 °C and were believed to have been influenced by the interference of Tinuvin (a UV stabilizer) at elevated temperatures higher than 50 °C. Although the desorption rate of SPAN‐40 increased with the temperature and decreased with the EAA content, the observed spectral behavior did not depend on the temperature and time. For all specimens stored over 50 °C, the peak at 1739 cm^?1 decreased in a few days and subsequently increased with a peak shift toward 1730 cm^?1. This arose from the carbonyl stretching vibration of Tinuvin, possibly because of oxidation or degradation at elevated temperatures. In addition, the incorporation of EAA into the LLDPE blend suppressed the desorption rate of SPAN‐40 and retarded the appearance of the 1730 cm^?1 peak. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1114–1126, 2004     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

Stability control of the electrooptic effect with new maleimide copolymers containing photoreactive tricyanopyrrolidene‐based chromophores

New photocrosslinkable maleimide copolymers have been synthesized by the attachment of a tricyanopyrrolidene‐based chromophore. The 2‐(3‐cyano‐4‐(2‐{4‐[hexyl‐(6‐hydroxy‐hexyl)‐amino]‐phenyl}‐vinyl)‐5‐oxo‐1‐{4‐[4‐(3‐oxo‐3‐phenyl‐propenyl)‐ phenoxy]‐butyl}‐1,5‐dihydro‐pyrrol‐2‐ylidene)‐malononitrile chromophore exhibits nonlinear optical activity and contains a chalcone moiety that is sensitive to UV light (λ = 330–360 nm) for crosslink formation. The maleimide monomers have also been functionalized with chalcone moieties. The resultant copolymers exhibit great processability, and one of them shows a maximum electrooptic coefficient of 90 pm/V at 1300 nm. We could control the thermal stability of the electrooptic coefficient with the newly synthesized photoreactive copolymers successfully. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 531–542, 2007     

Photoswitching of holographic polymer-dispersed liquid crystals doped with chiral dopant

Chiral dopants were added to the formulation of holographic polymer-dispersed liquid crystals and the effects studied in terms of grating formation dynamics, morphology, diffraction efficiency, contrast ratio and electro-optical properties of the films. A gradual increase of real-time diffraction efficiency, decrease of droplet size and increase of diffraction efficiency of the composite film were obtained with the addition and increasing content of chiral dopant, due to the increased viscosity of the liquid crystal (LC) doped with the chiral dopant leading to decreased droplet coalescence. The contrast ratio decreased with increasing content of chiral dopant due to the difficult orientation of LC molecules caused by the formation of a helical structure. Addition of a small amount of the chiral dopant increased the driving voltage slightly, whereas the decay time is decreased significantly as a result of the high twisting of the helical structure.     

Biphotonic recording effect of polarization gratings based on dye-doped liquid crystal films

This study investigates a holographic recording effect of biphotonic polarization gratings (BPGs) written on dye-doped liquid crystal (DDLC) films. One linearly polarized green light (λ_G = 514.5 nm) and a polarization-modulated interference pattern formed by two mutually coherent orthogonal (±45° with respect to the polarization of the green light) polarized red lights simultaneously excite the DDLC films to generate a BPG. The formation of BPGs depends primarily on the dichroism of the dye molecules and a sequence of mechanisms: photoisomerization, anisotropic adsorption and inhibition of dye adsorption. The cis-isomer absorbance-modulated distribution associated with the red polarization-modulation pattern induces the dye adsorption-modulated pattern, in turn, yielding the permanent BPG which generates a modulated twisted nematic (TN) structure pattern in the sample. It is found that each BPG is verified to be electrically switchable and thermally erasable. The switching time is in the order of milliseconds. Additionally, the recording time to form a BPG decreases with increasing intensity of the green pump beam.     

Recent changes in A-level Mathematics: is the availability and uptake of mechanics declining yet more?

In the past 6 years changes have occurred in GCE A-levels. Inparticular, there have been several major changes in A-levelMathematics courses. As engineering students are usually requiredto have studied A-level Mathematics, or its equivalent, thesechanges have had an effect on their prior mathematical knowledge.Moreover, engineering students traditionally obtained a goodgrounding in mechanics as part of their A-level Mathematicsqualification. However, mechanics, which was once included inthe core syllabus, is now optional. This article investigatesthe current availability and uptake of mechanics modules withinA-level Mathematics courses in schools. Comparisons are drawnbetween these results and results of a survey of schools in2004 and surveys of first year engineering students conductedin 2004 and 2005. It is found that there is a decline in theavailability of mechanics modules and the uptake of more thanone mechanics module has also decreased. The implications ofthese findings for engineering educators are discussed.     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

Determination of carbamazepine by chemiluminescence detection using chemically prepared tris(2,2'-bipyridine)ruthenium(III) as oxidant.

A new chemiluminescence method for the determination of carbamazepine (CBZ) has been developed. The method is based on the chemiluminescence produced in the reaction of tris(2,2'-bipyridine)ruthenium(III) and CBZ in an acidic medium. The chemiluminescence intensity was enhanced by organic solvents in the reaction system. Under the optimum experimental conditions, the calibration curve was linear over the range 4.0 x 10(-3)-8.6 x 10(-7) mol/L for CBZ. The detection limit (S/N = 3) was 2.5 x 10(-7) mol/L and the relative standard deviation of six replicate measurements was 2.6% for 4.0 x 10(-4) mol/L of CBZ. The possible reaction mechanism were also discussed. The chemiluminescence method was successfully applied to assay the CBZ contents in pharmaceutical tablets.