Optimization of Transducer Location for Novel Non-Intrusive Methodologies of Diagnosis in Diesel Engines

The health monitoring has been studied to ensure integrity of design of engine structure by detection, quantification, and prediction of damages. Early detection of faults may allow the downtime of maintenance to be rescheduled, thus preventing sudden shutdown of machines. In cylinder pressure developed, vibrations and noise emissions data provide a rich source of information about condition of engines. Monitoring of vibrations and noise emissions are novel non-intrusive methodologies for which positioning of various transducers are important issue. The presented work shows applicability of these diagnosis methodologies adopted in case of diesel engines. The effects of changing various fuel injection parameters was analyzed. Scope of using non-intrusive technique has been analyzed by changing locations of microphone. Novelty of this worklies in exploring signal processing methods for various locations around the engine test set up. Various frequency ranges of contributing noise and vibration sources were identified. Time-Frequency analysis showed the onset of various cyclic. Based on the identification of various frequency bands, it is possible to device suitable filters in order to extract more information.     

Comparative Study of LiInSe2 Single Crystals for Thermal-Neutron Detection

Crystallography Reports - Two LiInSe2 single crystals, grown under different conditions, have been studied. Characteristics of these crystals for neutron detection have been compared using...     

Composition and Antifungal Activity of Lipids from Seeds of Atriplex tatarica

Chemistry of Natural Compounds -     

On the Tender X-Ray Flat-Field Spectrograph with a Concave VLS Grating

Journal of Russian Laser Research - We analyze the way of advancing to tender X-rays the short-wavelength bound of the operating range of flat-field grating spectrographs. We design two VLS grating...     

Assessment of Noise Exposure of Sawmill Workers in Southwest,Nigeria

Economic wood processing employs the use of industrial machines for cutting, shaping, milling, and sawing timber, thereby leading to the generation of high levels of noise. Published data from empirical studies have categorized noise as an environmental hazard of global significance. Furthermore, noise exposure limits for different industries and all the industrial machines available has not been formally established as it presently exists in developed nations around the world. Therefore, this study assessed the daily exposure of sawmills workers to noise in Southwestern Nigeria. Reconnaissance surveys were first carried out in Osun, Oyo, Ondo, Ekiti, Lagos, and Ogun States to select sawmills that were fully operational and fit for the study. Two fully functional sawmills in two cities of each State were eventually selected for data collection, making a total of 24 sawmills, while the Circular Machines (CM), Planer Machines (PM), and Band-saw Machines (BM) were the machines in each sawmill considered. Two machines each of CM, PM, and BM were considered in each sawmill, making a total of forty-eight (48) machines each of CM, PM, and BM. Sound data were collected between 7 am and 7 pm each day for six days (between Monday and Saturday) using Extech 407732 sound level meter and all stabilized measurements were taken three times at different intervals. The data collected were in three different periods: Machine No-work Period (NP_m), Machine Idle Period (IP_m), and Machine Working Period (WP_m). A two–way Analysis of Variance (ANOVA) was carried out at P < 0.05 to determine whether there is a significant difference in the sound level average before and after the break, for both the idle and working periods of the three machines considered. This was also done to determine whether there is a significant difference between the sound level average of the results collected during idle and working periods of the three machines. Noise Pollution Levels (L_np) ranged from 83.20 dB (PM) to 107.65 (BM) and 93.42 (CM and PM) – 116.00 (BM) respectively, while IP_m also gave the least noise pollution level of 95.79 dB and WP_m gave the highest level of 102.88 dB. The results revealed that all the machines’ L_np values in the working period are more than the 90 dB acceptable limit the recommendation value of 90 dB while 89.6% of CMs, 75% of PMs, and 89.6% of BM had their L_np above 90 dB in the idle period respectively. The minimum and the maximum noise dose levels for IP_m, WP_m and overall are 0.09 (BM) and 2.37 (CM), 0.50 (CM), and 4.77 (PM) and 0.69 (BM) and 6.64 (PM) respectively. The study found out that the fundamental contributing factors to the high noise levels in sawmills are poor machine maintenance, use of old and obsolete machines, poor housekeeping strategy, limited space, workers’ negligence, lack of PPE, and lack of occupational safety training. The study recommends that proper workplace practices such as use of personal protective equipment, new and modern machines, training, and occupational safety programmes be implemented in the considered sawmills.     

Operator Interpolation and Systems of Linear Equations and Inequalities in Euclidean Spaces

Ukrainian Mathematical Journal - We establish new criteria of compatibility for a linear system of equations (equivalent to the Kronecker–Capelli theorem) or inequalities (equivalent to the...     

Effect of External Factors on the Ferromagnetic Resonance Line Width in Exchange-Biased Structures

Physics of the Solid State - The external factors which influence the ferromagnetic resonance (FMR) line width in bilayer (ferromagnet/antiferromagnet) exchange-biased systems are studied. The...     

Polycrystallinity in Gallium Arsenide Crystals Grown by the Czochralski Method

Crystallography Reports - The specific features of the formation of crystallites in gallium arsenide crystals grown by the Czochralski method have been investigated. The crystallites are found to...     

Biosynthesis of zinc oxide nanoparticles using Euphorbia milii leaf constituents: Characterization and improved photocatalytic degradation of methylene blue dye under natural sunlight

A facile biosynthesis route was followed to prepare zinc oxide nanoparticles (ZnO NPs) using Euphorbia milii (E. milii) leaf constituents. The SEM images exhibited presence of spherical ZnO NPs and the corresponding TEM images disclosed monodisperse nature of the ZnO NPs with diameter ranges between 12 and 20 nm. The Brunauer–Emmett–Teller (BET) analysis revealed that the ZnO NPs have specific surface area of 20.46 m²/g with pore diameter of 2 nm–10 nm and pore volume of 0.908 cm³/g. The EDAX spectrum exemplified the existence of Zn and O elements and non-appearance of impurities that confirmed pristine nature of the ZnO NPs. The XRD pattern indicated crystalline peaks corresponding to hexagonal wurtzite structured ZnO with an average crystallite size of 16.11 nm. The FTIR spectrum displayed strong absorption bands at 512 and 534 cm^?1 related to ZnO. The photocatalytic action of ZnO NPs exhibited noteworthy degradation of methylene blue dye under natural sunlight illumination. The maximum degradation efficiency achieved was 98.17% at an illumination period of 50 min. The reusability study proved considerable photostability of the ZnO NPs during photocatalytic experiments. These findings suggest that the E. milii leaf constituents can be utilized as suitable biological source to synthesis ZnO NPs for photocatalytic applications.