An NMR study of the freezing of emulsion-containing drops

Various nuclear magnetic resonance (NMR) techniques were used to monitor the freezing behaviour of suspended 2-mm-diameter drops. The drops were composed of hydrocarbon oils emulsified in either water or water/sucrose mixtures. As such they were good model systems for the study of spray freezing, sharing structural similarities with potential products such as ice cream. In particular, simple 1H NMR spectroscopy was used to monitor and individually quantify the freezing or solidification behaviour of the various constituent species of the drops. In addition, the effect of freezing on the emulsion droplet size distribution (and hence emulsion stability) was also measured based on NMR self-diffusion measurements. The effect of freeze/thaw cycling was also similarly studied. The nucleation temperature of the emulsion droplets was found to depend on the emulsion droplet size distribution: the smaller the droplets, the lower the nucleation temperature. Emulsion droplet sizing indicated that oil-in-sucrose-solution emulsions were more stable, showing minimal coalescence, whereas oil-in-water emulsions showed significant coalescence during freezing and freeze/thaw cycling.     

Identification of homemade inorganic explosives by ion chromatographic analysis of post-blast residues

Anions and cations of interest for the post-blast identification of homemade inorganic explosives were separated and detected by ion chromatographic (IC) methods. The ionic analytes used for identification of explosives in this study comprised 18 anions (acetate, benzoate, bromate, carbonate, chlorate, chloride, chlorite, chromate, cyanate, fluoride, formate, nitrate, nitrite, perchlorate, phosphate, sulfate, thiocyanate and thiosulfate) and 12 cations (ammonium, barium(II), calcium(II), chromium(III), ethylammonium, magnesium(II), manganese(II), methylammonium, potassium(I), sodium(I), strontium(II), and zinc(II)). Two IC separations are presented, using suppressed IC on a Dionex AS20 column with potassium hydroxide as eluent for anions, and non-suppressed IC for cations using a Dionex SCS 1 column with oxalic acid/acetonitrile as eluent. Conductivity detection was used in both cases. Detection limits for anions were in the range 2-27.4ppb, and for cations were in the range 13-115ppb. These methods allowed the explosive residue ions to be identified and separated from background ions likely to be present in the environment. Linearity (over a calibration range of 0.05-50ppm) was evaluated for both methods, with r(2) values ranging from 0.9889 to 1.000. Reproducibility over 10 consecutive injections of a 5ppm standard ranged from 0.01 to 0.22% relative standard deviation (RSD) for retention time and 0.29 to 2.16%RSD for peak area. The anion and cation separations were performed simultaneously by using two Dionex ICS-2000 chromatographs served by a single autoinjector. The efficacy of the developed methods was demonstrated by analysis of residue samples taken from witness plates and soils collected following the controlled detonation of a series of different inorganic homemade explosives. The results obtained were also confirmed by parallel analysis of the same samples by capillary electrophoresis (CE) with excellent agreement being obtained.     

How the electrolyte limits fast discharge in nanostructured batteries and supercapacitors

Solid state and interfacial processes are not necessarily the principal rate limiting process during fast discharge of LiFePO₄ composite electrodes with particle size less than 1 μm. A simple model based on salt diffusion to a sharp discharge front explains the observed dependence of discharge rate on electrode thickness, electrolyte concentration, lithium transference number, and dilution of the active material. The effect of changing the electrolyte is dramatic, e.g. discharge to 25% capacity was obtained on a 40 μm thick electrode after only 4 s in an optimised electrolyte, aqueous Li₂SO₄, showing a rate of 900 C as compared with less than 10 C for a similar cell with an ionic liquid as the electrolyte.     

PHOTOCHEMISTRY OF BIOLOGICAL MOLECULES-V. A MECHANISTIC STUDY OF THE PHOTOLYSIS OF CYCLOALANYLALANINE IN THE SOLID STATE

Abstract— Earlier studies of the photodamage induced by 254 nm irradiation of linear alanine peptides in the solid state have been supplemented by an investigation into the gaseous photoproducts from the cyclic dipeptide, 3,6-dimethyl-2,5-diketopiperazine. The trans and cis isomers have been prepared and the photoproducts compared with those from the DL-mixture. The conformation of the molecule does influence the yield of gaseous products. CO was produced by peptide bond rupture with concomitant release of hydrogen. CO₂ was also produced. The use of N- and C-deuterated analogues together with relevant crystallographic and EPR data has enabled a detailed study of the mechanism of photode-gradation to be made, from which it is concluded that the methyl protons are not inert but rather are the major source of the hydrogen observed on photolysis.     

A rapid,chromatography-free route to substituted acridine–isoalloxazine conjugates under microwave irradiation

Microwave irradiation was applied to a sequence of condensation reactions from readily available 9-chloroacridines to provide a range of novel acridine–isoalloxazine conjugates. The combination of these two moieties, both of biological interest, was achieved by a chromatography-free route.     

Droplet migration in emulsion systems measured using MR methods

The migration of emulsion droplets under shear flow remains a largely unexplored area of study, despite the existence of an extensive literature on the analogous problem of solid particle migration. A novel methodology is presented to track the shear-induced migration of emulsion droplets based on magnetic resonance imaging (MRI). The work is in three parts: first, single droplets of one Newtonian fluid are suspended in a second Newtonian fluid (water in silicone oil (PDMS)) and are tracked as they migrate within a Couette cell; second, the migration of emulsion droplets in Poiseuille flow is considered; third, water-in-silicone oil emulsions are sheared in a Couette cell. The effect of (a) rotational speed of the Couette, (b) the continuous phase viscosity, and (c) the droplet phase concentration are considered. The equilibrium extent of migration and rate of migration increase with rotational speed for two different emulsion systems and increased continuous phase viscosity, leads to a greater equilibrium extent of migration. The relationship between the droplet phase concentration and migration is however complex. These results for semi-concentrated emulsion systems and wide-gap Couette cells are not well described by existing models of emulsion droplet migration.     

Geometric effects on surface roughness in electrodeposition

^** Email: ranga{at}ufl.edu Our aim is to understand the early stages of roughness growthin electrodeposition. We present a study of the branching ofsteady planar electrode surfaces to steady non-planar electrodesurfaces as the voltage imposed at a cathode is decreased throughits critical value. We aim to discover the type of branchingand to learn whether or not the new branches can be detectedby measuring the current. The cross-sectional shape of the electrodemakes a difference. Circular electrodes lead to transcriticalbranching; ordinarily, rectangular electrodes lead to a pitchfork,sometimes forward and sometimes backward.