Minimization of water vapor interference in the analysis of non-methane volatile organic compounds by solid adsorbent sampling

Water vapor can be a significant interference in the analysis of air for non-methane volatile organic compounds (NMVOCs) using solid-adsorbent sampling techniques. The adsorbent materials used in sampling cartridges have different hydrophobic characteristics, and it is therefore necessary to characterize solid-adsorbent cartridges over a wide range of humidity. Controlled humidity experiments were performed to assess the extent of water vapor interference when samples are collected onto AirToxics solid-adsorbent cartridges. It was found that elevating the temperature of the cartridge to 10 degrees C above the temperature of the air sample greatly reduced water vapor adsorption and interferences and resulted in > or = 90% recovery of NMVOCs, biogenic VOCs and chlorofluorocarbons. Similar collection efficiencies were obtained at ambient temperature by reducing the relative humidity to > or = 60% in the sample by dilution with dry, scrubbed ambient air. A procedure also was developed and optimized for dry-purging cartridges prior to analysis. However, under optimized conditions, significant losses of C3-C5 compounds still occurred under highly humid conditions. It was determined that these losses were due to reduced retention during sampling rather than loss during the dry purge procedure. The dry purge method was shown to be adequate at high humidities for sampling NMVOCs with retention indices greater than 500.     

Stereochemistry of the thermal isomerizations of (2S,3R-methoxymethyl-2,3-dideuterio-1-(dideuteriomethylene)cyclopropane

The (2S,3R) isomer of 2-methoxymethyl-2,3-dideuterio-1-(dideuteriomethylene)cyclopropane has been synthesized and heated at 198.8°: from the experimentally observed mol fractions of the eight isomers of 2,3,α,α,- and 2,3,3,α - tetradeuterio - 2 - methoxymethyl - 1 - methylenecyclopropane in the pyrolysis product mixture have been derived rate constants for seven distinct modes of isomerization. One-center thermal epimerizations at C(2) and C(3) and the C(2)C(3) two-center epimerization are of kinetic importance. Only two of four observable stereochemical modes for carbon [1,3] shifts are seen: there is inversion of stereochemistry at the migrating C atom, while the C(3)H trans to C(2)-CH₂OCH₃ in starting material becomes syn 4 : 1 C(α)-H in the [1,3] shift product. Stereomutation at C(2) does not occur along the reaction coordinate for [1,3] carbon shifts.     

Metallacycloalkanes: I. Preparation and characterisation of α,α′-bipyridyl-5-nickela-3,3,7,7-tetramethyl-trans-tricyclo[4.1.0.02,4]heptane

Oxidative addition of 2 molecules of 3,3-dimethylcyclopropene (I) to α,α′-bipyridyl(1,5-cyclooctadiene)nickel(0) (III) gave the title compound (IV) in over 90% yield. Complex IV was characterized by mass, ¹H NMR and ¹³C NMR spectroscopy. Its structure was determined by X-ray diffraction (a 13.7081(2), b 14.638(2), c 9.5139(1) Å, β 110.82(1)°, C2/c, R = 0.05 for 1614 reflections).     

Synthesis and antiinflammatory activity of the sulfoxides of 4-[3-(dimethylamino)propyl] - 3,4- dihydro- 2-(1-hydroxyethyl)-3-phenyl-2H-1,4-benzothiazine

Oxidation of 4-[3-(dimethylamino)propyl]-3,4-dihydro-2-(1-hydroxyethyl)-3-phenyl-2H-1,4-benzothiazine, hydrochloride (I) with hydrogen peroxide yielded a mixture of two sulfoxides (II). Since this mixture exhibited antiinflammatory activity, the two components (Isomers A and B) were prepared in purified form by oxidation of I with N-chlorosuccinimide and hydrogen peroxide, respectively. Isomer A was more potent than Isomer B in the carrageenin-induced edema test.     

Effect of pressure on coupled electronic ground and excited states determined from luminescence spectra of trans-dioxorhenium(V) complexes

Pressure-dependent luminescence spectra of trans-dioxo complexes of rhenium(V) with ancillary ethylenediamine ligands exhibit resolved vibronic structure in the O=Re=O symmetric stretching mode at room temperature. The intensity distribution within the vibronic progression changes with pressure, leading to band shapes that are also pressure-dependent. These spectroscopic features arise from coupled electronic states and depend on the energy differences between ground and excited states, which vary by 2500 cm(-1) for the three complexes with ethylenediamine, tetramethylethylenediamine, and tetraethylethylenediamine ancillary ligands. We describe the pressure-dependent vibronic structure and band shapes with anharmonic adiabatic potential energy surfaces for the ground states of all complexes. The calculated spectra reveal the pressure dependence of the energies of electronic origins, luminescence band maximums, offsets between ground- and emitting-state potential minimums, and vibrational frequencies. The largest pressure effects are observed where the coupled electronic states are close in energy.     

BIOCHEMICAL FACTORS AFFECTING THE QUANTUM EFFICIENCY OF HYDROGEN PRODUCTION BY MEMBRANES OF GREEN PHOTOSYNTHETIC BACTERIA*

Abstract— Photohydrogen production, 200-700 μmol H₂ h^?1 (mg bacteriochlorophyll a)^?1 has been obtained in a system containing unit membrane vesicles (Complex I) from the green photosynthetic bacterium Chiorobium limicola f. thiosulfatophilum, ascorbate, N,N,N′,N′-tetramethyl-p-phenylene-diamine, dithioerythritol, an oxygen scavenging mixture, either methyl viologen (MV) or clostridial ferredoxin (CPS Fd) as electron carrier, and either CPS hydrogenase or platinum asbestos as catalyst. All components are necessary for maximum activity, and spinach Fd cannot be substituted for CPS Fd. Higher rates of photohydrogen production are obtained using MV or CPS Fd with hydrogenase than with MV and Pt asbestos. The highest quantum efficiencies (7–10% at 0.2–0.9 mW absorbed light and over 20% at lower light) were obtained with CPS Fd, hydrogenase and non-saturating 812 nm light. With saturating white light, however, rates of photohydrogen production varied relatively little among the various combinations of electron carrier and catalyst tested. The reaction rate is unaffected by 0.03% Triton X-100, and is insensitive to treatment with antimycin a or m-chloro-carbonyl cyanide phenylhydrazone. This indicates that neither electron flow through an endogenous cyclic chain, nor maintenance of a proton gradient are involved in this process.     

A Branched Pore Model Analysis for the Adsorption of Acid Dyes on Activated Carbon

A new branched-pore adsorption model has been developed using an external mass transfer coefficient, K _f, an effective diffusivity, D _eff, a lumped micropore diffusion rate parameter, K _b, and the fraction of macropores, f, to describe sorption kinetic data from initial adsorbent-adsorbate contact to the long-term adsorption phase. This model has been applied to an environmental pollution problem—the removal of two dyes, Acid Blue 80 (AB80) and Acid Red 114 (AR114), by sorption on activated carbon. A computer program has been used to generate theoretical concentration-time curves and the four mass transfer kinetic parameters adjusted so that the model achieves a close fit to the experimental data. The best fit values of the parameters have been determined for different initial dye concentrations and carbon masses. Since the model is specifically applicable to fixed constant values of these four parameters, a further and key application of this project is to see if single constant values of these parameters can be used to describe all the experimental concentration-time decay curves for one dye-carbon system.The error analysis and best fit approach to modeling the decay curves for both dye systems show that the correlation between experimental and theoretical data is good for the fixed values of the four fitted parameters. A significantly better fit of the model predictions is obtained when K _f, K _b and f are maintained constant but D _eff is varied. This indicates that the surface diffusivity may vary as a function of surface coverage.