Determination of mercury in seafood by flow injection-cold vapor atomic absorption spectrometry after microwave digestion: NMKL interlaboratory study. Nordic Committee on Food Analysis

Ten laboratories participated in an interlaboratory method-performance (collaborative) study of a method for the determination of mercury in foods of marine origin by flow injection-cold vapor atomic absorption spectrometry after wet digestion using a microwave oven technique. The study was preceded by a training round of samples of known identity. The method was tested on a total of 7 seafood products: blue mussel (Mytilus edulis), cod muscle (Gadus morhua), crab (Cancer pagurus), scampi (Nephrops norwegicus), black scabbard fish (Aphnopus carbo), longnose velvet dogfish (Centroscymus crepidater), and Portuguese dogfish (Cenbroscymus coelolepis) with mercury concentrations of 0.14, 0.24, 0.35, 0.59,11.42, 4.2, and 13.2 microg/g, respectively. The materials were presented to the participants in the study as blind duplicates, and the participants were asked to perform single determinations on each sample. Repeatability relative standard deviations (RSDr) for mercury ranged from 2.4 to 14.0%. Reproducibility relative standard deviations (RSDR) ranged from 7.7 to 16.6%. HORRAT values for all samples were <1.0.     

Monitoring of ethanol during fermentation using a microbial biosensor with enhanced selectivity

The present study is concerning the construction of ferricyanide-mediated Gluconobacter oxydans cell ethanol biosensor. The size exclusion effect of a cellulose acetate membrane was used for elimination of glucose interferences during ethanol assays in real samples. A typical response time of the biosensor was 13 s with a high sensitivity of 3.5 microA mM(-1). The microbial biosensor exhibits a very low detection limit of 0.85 microM and a wide linear range from 2 to 270 microM. The operational stability was excellent. During 8.5 h of repetitive ethanol assays, no decrease in the sensor sensitivity was observed. The biosensor was successfully used in the off-line monitoring of ethanol fermentation with a good agreement with HPLC measurements (R(2)=0.998).     

Compehensive two-dimensional gas chromatography (GC×GC) and its applicability to the characterization of complex (petrochemical) mixtures

In general, petrochemical products contain only a limited number of chemical classes of compounds (sample dimensionality). The enormous number of individual components within these classes, however, soon puts limitations upon a single chromatographic technique when it comes to adequate characterization of these products. Comprehensive two-dimensional gas chromatography (GC×GC) clearly opens the possibility of estimating the composition of hydrocarbon mixtures in a far more detailed fashion than hitherto possible. Although the emphasis of papers of GCxGC thus far almost exclusively applies to the unsurpassed peak-capacity, in the oil industry there is a need for characterization, rather than for analyzing all the individual compounds. In principle a GCxGC system can provide an almost perfect match between its intrinsic properties and the dimensionality of oil samples. To establish the applicability of GCxGC towards petrochemical analytical challenges, a commercially aavailable prototype instrument was subjected to an exhaustive characterization of a typical hydrocarbon precess stream and a fast characterization of a light gas oil. Although there are no fundamental limitations towards the quantitative aspects of a GCxGC system, this paper confines itself to qualitative results only. Quantitative aspects of GCxGC will be published in a forthcoming paper.     

Amperometry with two polarizable electrodes. XVI

Summary Conditions for the magnesium determination in alkaline solution by EDTA titration with biamperometric indication were examined. The most preferable pH range was found to be above 9.6. A reliable determination can be carried out in the presence of Ca, Ni, Cu and Co up to the ratio of 11. In the case of higher concentrations of Cu and Ni masking with potassium cyanide can be used. In this case, however, a change of the titration curves occurs.A new method for the determination of water-hardness by biamperometric indication is proposed. It is rapid and accurate and meets the requirements of routine and research work (error: ±1%).

---

Zusammenfassung Die Bedingungen für die Magnesiumbestimmung in alkalischer Lösung durch Titration mit ÄDTA bei biamperometrischer Endpunktsanzeige wurden untersucht. Der günstigste pH-Bereich liegt über 9,6. Zuverlässige Bestimmungen können in Gegenwart von Ca, Ni, Cu und Co bis zum Verhältnis 11 ausgeführt werden. Höhere Konzentrationen an Cu oder Ni können mit KCN maskiert werden, wobei allerdings eine Umkehrung der Kurven auftritt.Ein Verfahren zur Wasserhärtebestimmung mit biamperometrischer Indikation wird vorgeschlagen, das schnell durchzuführen ist und genaue Werte liefert (Fehler ±1%).

---

---

Part XV: Vorlíek, J., and P. Peták: Microchem. J. 12, 466–471 (1967).     

The synthesis of 4‐amino‐3‐(2‐pyridyl)pyrazolo[5,1‐c][1,2,4]triazine and some of its derivatives

A mixture of both geometrical isomers of hydrazones 3a‐3e was obtained by the coupling reactions of pyrazole‐3‐diazonium salts 2a‐2d and benzenediazonium chloride 2e with 2‐pyridylacetonitrile 1 . Hydrazones 3a‐3d were cyclized to the corresponding 4‐amino‐3‐(2‐pyridyl)pyrazolo[5,1‐c][1,2,4]triazines 4a‐4d.     

Kinetic parameters of the In(III)/In(I) electrode reaction in bromide medium

The electrode kinetic parameters of the In(III)/In(I) couple in acidic 4M bromide solution have been determined by means of the rotating disc electrode technique.

---

Die elektrochemisch-kinetischen Parameter des In(III)/In(I)-Redoxsystems in Bromidlösung (Kurze Mitteilung)

Zusammenfassung Die elektrochemisch-kinetischen Parameter am In(III)/In(I)-Redoxsystem wurden in saurer 4-M-Bromidlösung mittels der rotierenden Scheibenelektrode bestimmt.

     

Longitudinal acceptance computation for A 50 MeV race track microtron

The algorithm for analysing of longitudinal motion and for calculating phase trajectory in race track microtron (RTM) with small injection energy and small energy gain per turn is described. A longitudinal acceptance is calculated.We are indebted to E. A. Perelshtein and N. Ju. Kazarinov and A. Ju. Molodozhencev for stimulating advices. We thank M. Slodika for work with program coding.