Solid phase synthesis of azapeptides using an automatic synthesizer

Peptides containing azaglycine located terminally or within the backbone have been prepared in the solid phase by means of an automatic synthesizer.     

Superfield form of discrete gauge states in ĉ = 1 2d supergravity

A general formula for the discrete states (NeveuSchwarz sector) in N = 1 2D super-Liouville theory is written down in the world-sheet supersymmetric form. We then derive a set of gauge states at the discrete momenta. These discrete gauge states are shown to carry the ω_∞ charges and serve as the symmetry parameters in the old covariant quantization of the theory.     

A possibility of parallel and anti-parallel diffraction measurements on neutron diffractometer employing bent perfect crystal monochromator at the monochromatic focusing condition

In a conventional diffractometer having single monochromator, only one position, parallel position, is used for the diffraction experiment (i.e. detection) because the resolution property of the other one, anti-parallel position, is very poor. However, a bent perfect crystal (BPC) monochromator at monochromatic focusing condition can provide a quite flat and equal resolution property at both parallel and anti-parallel positions and thus one can have a chance to use both sides for the diffraction experiment. From the data of the FWHM and the Δd/d measured on three diffraction geometries (symmetric, asymmetric compression and asymmetric expansion), we can conclude that the simultaneous diffraction measurement in both parallel and anti-parallel positions can be achieved.     

Generation of 0.2-TW 5.5-fs optical pulses at 1 kHz using a differentially pumped hollow-fiber chirped-mirror compressor

Optical pulses with 1.1-mJ energy and 5.5-fs duration have been generated at 1-kHz repetition rate from a chirped pulse amplification Ti:Sapphire laser incorporating a differentially pumped hollow-fiber chirped-mirror compressor. The effects of self-focusing and multi-photon ionization during the beam propagation were minimized by differentially pumping the hollow fiber filled with neon. The spectral broadening at the hollow-fiber compressor was optimized by adjusting gas pressure, laser intensity, and laser chirp, covering from 540 nm to 950 nm. PACS 42.65.Jx; 42.65.Re     

Control of the block copolymer morphology in templated epoxy thermosets

It has been found that by the addition of low concentrations of an amphiphilic block copolymer to an epoxy resin, novel disordered morphologies can be formed and preserved through curing. This article will focus on characterizing the influence of the block copolymer and casting solvent on the templated morphology achieved in the thermoset sample. The ultimate goal of this work is to determine the parameters that would control the microphase morphology produced. Epoxy resins blended with a series of amphiphilic block copolymers based on hydrogenated polyisoprene (polyethylene-alt-propylene or PEP) and polyethylene oxide (PEO), specifically, were investigated. In this article, the cure-induced order–order phase transition from the spherical to wormlike micelle morphology will also be discussed. It is proposed that the formation of the wormlike micelle structure from the spherical micelle structure is similar to the phase transition behavior that occurs in dilute block copolymer solutions as a function of the influence of the solvent on micelle morphology. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3338–3348, 2007     

“Slow” active control of combustion instabilities by modification of liquid fuel spray properties

This paper describes an experimental investigation of the feasibility of using “slow” active control approaches, which “instantaneously” change liquid fuel spray properties, to suppress combustion instabilities. The objective of this control approach was to break up the feedback between the combustion process heat release and combustor pressure oscillations that drive the instability by changing the characteristics of the combustion process (e.g., the characteristic combustion time). To demonstrate the feasibility of such control, this study used a proprietary fuel injector (Nanomiser^TM), which can vary its fuel spray properties, to investigate the dependence of acoustics–combustion process coupling, i.e., the driving of combustion instabilities, upon the fuel spray properties. This study showed that by changing the spray characteristics it is possible to significantly damp combustion instabilities. Furthermore, using combustion zone chemiluminescence distributions, which were obtained by Abel’s deconvolution synchronized with measured acoustic data, it has been shown that the instabilities were mostly driven midway between the combustor centerline and wall, a short distance downstream from the flame holder, where the mean axial flow velocity is approximately zero in the vortex near the flame holder. The results of this study strongly suggest that a “slow” active control system that employs controllable fuel injectors could be effectively used to prevent the onset of detrimental combustion instabilities.     

Stability control of the electrooptic effect with new maleimide copolymers containing photoreactive tricyanopyrrolidene‐based chromophores

New photocrosslinkable maleimide copolymers have been synthesized by the attachment of a tricyanopyrrolidene‐based chromophore. The 2‐(3‐cyano‐4‐(2‐{4‐[hexyl‐(6‐hydroxy‐hexyl)‐amino]‐phenyl}‐vinyl)‐5‐oxo‐1‐{4‐[4‐(3‐oxo‐3‐phenyl‐propenyl)‐ phenoxy]‐butyl}‐1,5‐dihydro‐pyrrol‐2‐ylidene)‐malononitrile chromophore exhibits nonlinear optical activity and contains a chalcone moiety that is sensitive to UV light (λ = 330–360 nm) for crosslink formation. The maleimide monomers have also been functionalized with chalcone moieties. The resultant copolymers exhibit great processability, and one of them shows a maximum electrooptic coefficient of 90 pm/V at 1300 nm. We could control the thermal stability of the electrooptic coefficient with the newly synthesized photoreactive copolymers successfully. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 531–542, 2007     

Bio-Plasmonics: Nano/micro Structure of Surface Plasmon Resonance Devices for Biomedicine

We have reported a novel design of surface plasmon resonance (SPR) device, which uses alternating dielectric layers to enhance the SPR signal quality and modulate its resonant position. Admittance loci method of thin film design has been used in the design of such a device. The use of biomolecular thin film, such as DNAs or Porteins, in this design can result in resonant condition of wavelength changes as well. Bio-plasmonics is proposed for the research and development of novel devices, which use biomolecules as a part of the plasmon oscillation system to actively interact with nano/micro structure.     

Photoswitching of holographic polymer-dispersed liquid crystals doped with chiral dopant

Chiral dopants were added to the formulation of holographic polymer-dispersed liquid crystals and the effects studied in terms of grating formation dynamics, morphology, diffraction efficiency, contrast ratio and electro-optical properties of the films. A gradual increase of real-time diffraction efficiency, decrease of droplet size and increase of diffraction efficiency of the composite film were obtained with the addition and increasing content of chiral dopant, due to the increased viscosity of the liquid crystal (LC) doped with the chiral dopant leading to decreased droplet coalescence. The contrast ratio decreased with increasing content of chiral dopant due to the difficult orientation of LC molecules caused by the formation of a helical structure. Addition of a small amount of the chiral dopant increased the driving voltage slightly, whereas the decay time is decreased significantly as a result of the high twisting of the helical structure.