Beta-exposure in a neutron activation laboratory

Summary In virtually all neutron activation analysis laboratories, researchers are given film badges known as thermoluminescence dosimeters (TLD's) that are monitored on a monthly basis. Sometimes additional pocket dosimeters are worn to get a daily reading of exposure, while in other instances ring badges are worn to assess beta doses. However, more than often little consideration is given to beta-exposure rates that arise from the plethora of radionuclides produced in the many types of samples irradiated. A common mistake is to assess gamma-exposures of activated samples that rely on the use of a beta-shield on the survey meter. Our experimental results have shown that there are many high energy beta-particles from neutron activated samples that can easily penetrate the beta-shield and thus give an underestimation of the total beta-exposure.     

A Noninvasive, on Wafer Method to Determine the Intrinsic Stress of a Polymer Layer

The method described in this paper allows an investigator to determine the intrinsic stress of a polymer layer in a way that does not result in damage to devices or test structures. The method requires that a small area of the polymer be released from the substrate to form a diaphragm. The diaphragm is stimulated with acoustic white noise and the diaphragm movement is monitored with a laser vibrometer. The first few resonance frequencies of the diaphragm are obtained using a laser vibrometer and then those frequencies are used to calculate the membrane intrinsic bi-axial tension.     

Projection of Markov Measures May Be Gibbsian

We study the induced measure obtained from a 1-step Markov measure, supported by a topological Markov chain, after the mapping of the original alphabet onto another one. We give sufficient conditions for the induced measure to be a Gibbs measure (in the sense of Bowen) when the factor system is again a topological Markov chain. This amounts to constructing, when it does exist, the induced potential and proving its Hölder continuity. This is achieved through a matrix method. We provide examples and counterexamples to illustrate our results.     

Conformational analysis of dipeptide‐derived polyisocyanides

The conformational properties of polymers derived from isocyanodipeptides have been investigated with a combination of model calculations, X‐ray diffraction, and circular dichroism spectroscopy. Depending on the configuration of the side chains, defined arrays of hydrogen bonds along the polymeric backbone are formed. This leads to a well‐defined conformation as, for example, expressed in the formation of lyotropic liquid‐crystalline phases and increased helical stability. Upon the disruption of the hydrogen bonds by a strong acid, a less well‐defined macromolecular conformation is observed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1725–1736, 2003     

On additives, morphological evolution and dielectric breakdown in low density polyethylene

A series of low density polyethylene systems has been studied with respect to structural evolution and short-term dielectric breakdown behaviour. All materials were based upon a single polymer, that is commonly used in high voltage applications, but with different additives. In all three of these systems, multiple melting transitions were observed, as a result of molecular fractionation effects during crystallization. In the virgin polymer, a space-filling banded spherulitic morphology was found to develop at low temperatures (102 °C and below) whereas, at higher temperatures, only a few isolated axialites were observed. Inclusion of the antioxidant resulted in greatly increased nucleation densities, such that, at low temperatures, no evidence of spherulitic organisation remained. At higher temperatures, sheaf-like lamellar aggregates developed, which were much smaller and much more numerous than in the case of the virgin polymer. Further addition of dicumyl peroxide (DCP) resulted in the rapid formation of a crosslinked network at 200 °C. Some crosslinking also occurred at 150 °C, but over a much longer timescale. Where extensive crosslinking occurred prior to crystallization, the resulting gel inhibited structural development, such that only a few small, isolated sheaves were able to form at 102 °C. In view of the principal application area of this material, the breakdown strength of each of the above systems was then measured and the whole data set was analysed statistically. When structural factors were considered alongside the statistics, no clear trends emerged to indicate that either the compositional or morphological variations were reflected in the short-term electrical failure processes.     

Preservation of Lipschitz constants by Bernstein type operators

Summary We obtain preservation inequalities for Lipschitz constants of higher order in simultaneous approximation processes by Bernstein type operators. From such inequalities we derive the preservation of the corresponding Lipschitz spaces.     

Investigation of organic impurities adsorbed on and incorporated into electroplated copper layers

At room temperature electroplated copper layers exhibit changes in resistivity, residual stress, and microstructure. This process, known as self-annealing, is intimately linked to the release of organic impurities, which stem from the incorporation of organic additives into the Cu layer in the course of the electroplating process. The behavior of these impurities during self-annealing, represented by the carbon content, could be detected by analytical radio frequency glow discharge optical emission spectrometry (GD-OES) and carrier gas hot extraction (CGHE). The precondition of a quantitative determination is a surface cleaning procedure to remove adsorbed organics from the copper surface. It was observed that at first almost all impurities have to leave the Cu metallization before an accelerated abnormal grain growth can start. The small amount of remaining organic species after self-annealing could be quantified by both examination techniques, GD-OES and CGHE.     

Post deposition purification of PTCDA thin films

The decomposition of perylene-3,4,9,10-tetracarboxylic dianhydride (PTCDA) molecules during evaporation of unpurified raw material in ultra high vacuum was studied. The fragments were identified by mass spectrometry and the influence of these fragments and further contaminations of the raw material on the electronic structure of PTCDA thin films was measured by photoemission spectroscopy. Annealing of contaminated PTCDA films was tested as cheap and easy to perform method for (partial) post deposition purification of the contaminated films.