OXIDATION OF TiAl,Ni AND Fe IN A DYNAMIC ENVIRONMENTAL SEM

IntroductionInmaterialscience,differentmicrostructuresofthesamematerialsmayinducediversebehaviorsanddifferentcharacteristics.Westwood(1988)showed,asanexample,thatthetreatmentofaluminumsurfacewithcommercialphosphoricacidproducedmechanicallyinterlockedoxide搘hiskers?approximately10nmindiameterand400nminlength,whichmechanicallyinterlocked.Thismicro-structurecankeepsuchaconglomeratebondedoverconsiderablerangesofstressandtemperature.Inahumidatmosphere,especiallythatcontainingchlorine,however,suchox…     

Structure and reflective properties of Al-Cu-Fe quasicrystalline thin film prepared by laser induced arc method

Al-Cu-Fe thin films were prepared by laser induced arc (laser-arc) method from a single source—Al₆₃Cu₂₅Fe₁₂ alloy, which was proved to consist of quasicrystalline phase together with approximant phase. The composition of the deposited films meets the requirement for formation of icosahedral symmetry phase. Quasicrystalline phase was obtained after annealing the amorphous as-deposit film samples. The optical properties of the samples were investigated. Thin film samples of Al, Cu and Fe deposited under the same condition were employed for comparison. The results showed specific reflective properties of Al-Cu-Fe quasicrystal thin film in some wavelength range. The optical conductivity of the films exhibited a negative peak, centered about 440 nm in range of 190 to 800 nm. The Al-Cu-Fe quasicrystal thin films could absorb almost all the ray in the wavelength range from 420nm to 450 nm. The ratio of absorption was greater than 99%.     

Preparation,thermal properties,and flame retardance of epoxy–silica hybrid resins

A novel epoxy system was developed through the in situ curing of bisphenol A type epoxy and 4,4′‐diaminodiphenylmethane with the sol–gel reaction of a phosphorus‐containing trimethoxysilane (DOPO–GPTMS), which was prepared from the reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) with 3‐glycidoxypropyltrimethoxysilane (GPTMS). The preparation of DOPO–GPTMS was confirmed with Fourier transform infrared, ¹H and ³¹P NMR, and elemental analysis. The resulting organic–inorganic hybrid epoxy resins exhibited a high glass‐transition temperature (167 °C), good thermal stability over 320 °C, and a high limited oxygen index of 28.5. The synergism of phosphorus and silicon on flame retardance was observed. Moreover, the kinetics of the thermal oxidative degradation of the hybrid epoxy resins were studied. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2354–2367, 2003     

Synthesis,and Antimycobacterial and Cytotoxic Evaluation of Certain Fluoroquinolone Derivatives

Certain 1‐ethyl‐ and 1‐aryl‐6‐fluoro‐1,4‐dihydroquinol‐4‐one derivatives were synthesized and evaluated for antimycobacterial and cytotoxic activities. Preliminary results indicated that, for 1‐aryl‐6‐fluoroquinolones, both 7‐(piperazin‐1‐yl)‐ and 7‐(4‐methylpiperazin‐1‐yl) derivatives, 9b and 11a , are able to completely inhibit the growth of M. tuberculosis at a concentration of 6.25 μg/ml, while the 7‐[4‐(2‐oxo‐2‐phenylethyl)piperazin‐1‐yl] derivative 13 exhibits only 31% growth inhibition at the same concentration. For 1‐ethyl‐6‐fluoroquinolones, both 7‐[4‐(2‐oxopropyl)piperazin‐1‐yl]‐ and 7‐[4‐(2‐oxo‐2‐phenylethyl)piperazin‐1‐yl]‐derivatives, 2a and 2b , respectively, show complete inhibition, while their 2‐iminoethyl and substituted phenyl counterparts 3a and 2c are less active. In addition, the 6,8‐difluoro derivative was a more‐favorable inhibitor than its 6‐fluoro counterpart ( 2b vs. 2d ). These results deserve full attention especially because 2a, 2b, 9b , and 11a are non‐cytotoxic at a concentration of 100 μM . Furthermore, compound 9b proved to be a potent anti‐TB agent with selective index (SI)>40 and an EC₉₀ value of 5.75 μg/ml.     

Analysis of nine rhubarb anthraquinones and bianthrones by micellar electrokinetic chromatography using experimental design

An efficient micellar electrokinetic chromatography (MEKC) method has been developed for the analysis of nine anthraquinones and bianthrones in rhubarb. A chemometric approach was used to search for the optimum conditions of separation. Those factors which were found to be significant with a screening design were further optimized with a central composite face-centered (CCF) design. Acetonitrile concentration was found to be the most influential, not only in resolution, but also in analysis time and peak asymmetry. With the optimized conditions: 15 mM sodium tetraborate/15 mM sodium dihydrogenphosphate buffer, 30 mM sodium deoxycholate, pH 8.6, 17 vol.% acetonitrile and 28 kV, nine tested analytes were baseline-separated within 14 min. The method was validated to analyze the rhubarb material. Solid-phase extraction (SPE) was manipulated to remove interfering substances. Five anthraquinones and two glycosidic bianthrones were detected and quantificated. The method should be suitable for determining these major active principles in rhubarb crude drugs.     

负离子元素杂质破坏模型

探讨了HfO₂薄膜中负离子元素杂质破坏模型，并得出薄膜中的杂质主要来源于 镀膜材料. 用电子束蒸发方法沉积两种不同Cl元素含量的HfO₂薄膜，测定薄膜 弱吸收和损伤阈值来验证负离子元素破坏模型. 结果表明，随着Cl元素含量的增加薄膜的弱 吸收增加损伤阈值减小. 这主要是因为负离子元素在蒸发过程中形成挥发性的气源中心而产 生缺陷，缺陷在激光辐照过程中又形成吸收中心. 因此负离子元素的存在将加速薄膜的破坏 . 关键词： 负离子元素杂质 缺陷 吸收     

Behaviors of the positive temperature coefficient of resistance of poly(styrene‐co‐n‐butylacrylate) filled with Ni‐plated core‐shell polymeric particles

Conductive composite films of poly(styrene‐co‐n‐butylacrylate) copolymers filled with low‐density, Ni‐plated core‐shell polymeric particles were prepared and their behaviors of positive temperature coefficient of resistance (PTCR) were investigated. When the conductive fillers in the composite film were loaded beyond the critical volume, 10 up to 25 vol %, composite films exhibited a unique electrical resistant transition behavior, which the electrical resistance rapidly increased by several orders of magnitude at the critical temperature. The PTCR transition temperature, in general, occurred before the glass transition temperature of polymer matrix. Further increased the conductive filler loading to 30 vol %, the overpacked conduction paths were formed in the entire composite and the PTCR effects became blurred. While the composite film treated with thermal cycle several times from room temperature up to 120 °C, the electrical resistivity increased accompanied with the shift of the PTCR transition to lower temperature. The reason might have been caused by the formed interfacial cracks within the composite film. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 322–329, 2007     

Synthesis of 5‐Radioiodoarabinosyl Uridine Analog for Probing the HSV‐1 Thymidine Kinase Gene

Tumor cells transduced with herpes simplex virus thymidine kinase gene have been intensively applied to the field of positron emission tomography via imaging of its substrate. As a pilot synthesis approach, a facile preparation of 5‐[¹²⁵I] iodoarabinosyl uridine starting from commercially available uridine is reported herein.     

Hydroxyapatite coating on porous silicon substrate obtained by precipitation process

Hydroxyapatite Ca₁₀(PO₄)₆(OH)₂ (HAP) is known as a bioactive and biocompatible material, HAP coatings were used to improve the biocompatible of substrate by many researcher, In this work, HAP thin films on porous silicon (PS) substrates have been prepared by aqueous precipitation method with rapid thermal annealing (RTA) processes. The HAP films had been prepared under the annealing temperature ranging from 300 to 1000 °C. By the measurement of X-ray diffraction (XRD), it was found that for the crystallinity optimization, the heat-treatment at 850–950 °C for 1 h would be favorable. Atomic force microscopy (AFM) and scanning electron microscope (SEM) measurements reveal a dense and smooth surface of the HAP film, and tightly adherence of the coating on porous silicon substrate after sintered. Thus, by this method, porous silicon could be increased its bioactivity and so that could be used in the biomedical area.