NiTi合金中马氏体相的低频力学谱研究

我们用最近研制成功的LMA型低频力学谱测试系统对NiTi合金马氏体相进行了在很大频率范围内（0．003～1Hz）的低频等温力学谱和温度谱的测量．我们研究的形状记忆合金NiTi（Ni50．2at％）试样长34mm，直径1mm细丝．经一定热处理，分别在333K．343K和353K做了内耗随频率的变化的测量。实验表明：频率越小，内耗越大，也就是内耗随频率减少而增大。同时我们采用阶梯升温的方法在八个温度下每个温度测量三种频率（1Hz，0．1Hz，0．01Hz）的内耗，结果清楚地表明：不同频率下，内耗峰都出现在372K（99℃）。而且频率越低，峰高越高。这是具有相变峰的特点：相变峰的峰温不随测量频率不同而变化，相变峰高度随频率减少而增大。我们还测量了在1Hz与0．5Hz频率下内耗随温度的变化。本文用马氏体相的位错理论初步讨论了上述实验结果。     

The operational performance of the Yale ESTU

The ESTU began operation in 1988 and achieved the design voltage of 20 MV in 1990. Since that time, improvements to the gas handling system, negative ion injector, accelerator terminal and control system have greatly increased its capability and reliability. Today, the ESTU can efficiently produce an extensive assortment of stable ions at wide-ranging energies in support of low-energy nuclear physics.     

Application of pressure sensitive paint measurement to a low-solidity cascade diffuser of a transonic centrifugal compressor

A pressure sensitive paint (PSP) measurement has been known as a pressure field measurement technique based on the oxygen quenching phenomenon of luminescence of specific luminophores. A PSP measurement was applied for pressure field measurement in a low-solidity circular cascade diffuser of a single-stage transonic centrifugal compressor with 5 in pressure ratio for HFC134a gas. The oxygen concentration was about 500 ppm. Ru (bath-phen) was adsorbed on a silica-gel thinlayer chromatography sheet, and the sheet was pasted onto the side-wall between the cascade vanes. A drastic change in luminescent intensity was recognized during a surge condition. Also the pressure variations based on luminescent intensity agreed well with the pressure fluctuations measured using a semiconductor pressure sensor with high-frequency-response. It was shown that a PSP measurement worked well to investigate the unsteady pressure fields in a circular cascade diffuser of a transonic centrifugal compressor. Moreover, the time response of PSP becomes clear as a problem to be overcome for the present.     

Molecular dynamics simulation of processing using AFM pin tool

A three-dimensional molecular dynamics (MD) model is utilized to investigate the effect of tool geometry on the deformation process of the workpiece and the nature of deformation process at the atomic-scale. Results show that different states exist between the atomic force microscope (AFM) pin tool and the workpiece surface, i.e. the non-wear state, the ploughing state, the state in which ploughing is dominant and the state in which cutting plays a key role. A relationship between the deformation process of the workpiece and the potential energy variation is presented. The potential energy variation of atoms in different deformed regions in the workpiece such as plastically deformed region, elastically deformed region and the mixed deformation region is different. The features of variations of potential energy are discussed.     

Primal cutting plane algorithms revisited

Dual fractional cutting plane algorithms, in which cutting planes are used to iteratively tighten a linear relaxation of an integer program, are well-known and form the basis of the highly successful branch-and-cut method. It is rather less well-known that various primal cutting plane algorithms were developed in the 1960s, for example by Young. In a primal algorithm, the main role of the cutting planes is to enable a feasible solution to the original problem to be improved. Research on these algorithms has been almost non-existent.  In this paper we argue for a re-examination of these primal methods. We describe a new primal algorithm for pure 0-1 problems based on strong valid inequalities and give some encouraging computational results. Possible extensions to the case of general mixed-integer programs are also discussed.     

A Novel Biomass Supported Na2CO3 System for Flue Gas Desulfurization

The breakthrough and stoichiometric SO2 adsorption efficiencies of a biomass supported Na2CO3 system (80 wt %Na2CO3/straw) have reached 48.9% and 80.6% respectively at a desulfurization temperature of 80℃.     

金属β-二酮化合物用于MOCVD法生长铁电氧化物薄膜

对用于MOCVD法生长铁电氧化物薄膜的金属β－二酮化合物的制备、结构及性质进行了评述，对它们在生长铁电薄膜中的应用现状进行了介绍，并对它们的应用前景作了展望。     

Generalized Longo–Rehren Subfactors and α-Induction

We study the recent construction of subfactors by Rehren which generalizes the Longo–Rehren subfactors. We prove that if we apply this construction to a non-degenerately braided subfactor N⊂M and α^±-induction, then the resulting subfactor is dual to the Longo–Rehren subfactor M⊗M ^opp⊂R arising from the entire system of irreducible endomorphisms of M resulting from α^plusmn;-induction. As a corollary, we solve a problem on existence of braiding raised by Rehren negatively. Furthermore, we generalize our previous study with Longo and Müger on multi-interval subfactors arising from a completely rational conformal net of factors on S ¹ to a net of subfactors and show that the (generalized) Longo–Rehren subfactors and α-induction naturally appear in this context. Received: 11 September 2001 / Accepted: 7 October 2001     

Complete ideals and singularities of space curves

We consider complete ideals supported on finite sequences of infinitely near points, in regular local rings with dimensions greater than two. We study properties of factorizations in Lipman special *-simple complete ideals. We relate it to a type of proximity, linear proximity, of the points, and give conditions in order to have unique factorization. Several examples are presented. Received: 2 February 2000 / in final form: 14 March 2001 / Published online: 18 January 2002