Behaviors of the positive temperature coefficient of resistance of poly(styrene‐co‐n‐butylacrylate) filled with Ni‐plated core‐shell polymeric particles

Conductive composite films of poly(styrene‐co‐n‐butylacrylate) copolymers filled with low‐density, Ni‐plated core‐shell polymeric particles were prepared and their behaviors of positive temperature coefficient of resistance (PTCR) were investigated. When the conductive fillers in the composite film were loaded beyond the critical volume, 10 up to 25 vol %, composite films exhibited a unique electrical resistant transition behavior, which the electrical resistance rapidly increased by several orders of magnitude at the critical temperature. The PTCR transition temperature, in general, occurred before the glass transition temperature of polymer matrix. Further increased the conductive filler loading to 30 vol %, the overpacked conduction paths were formed in the entire composite and the PTCR effects became blurred. While the composite film treated with thermal cycle several times from room temperature up to 120 °C, the electrical resistivity increased accompanied with the shift of the PTCR transition to lower temperature. The reason might have been caused by the formed interfacial cracks within the composite film. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 322–329, 2007     

Chemical Speciation of Amphoteric Ions on Semi‐Dry Scrubber Residue and Bag‐House Ash from MSWI

Two series of size‐fractionated combusted residues, a bag‐house ash and a scrubber residue, from a municipal solid waste incinerator (MSWI) were prepared and extracted by means of sequential chemical extraction (SCE) procedures proposed by Tessier. Concentrations of water‐soluble phase, exchangeable phase, carbonated phase, Fe/Mn oxide phase, organic matter phase, and residual phase bound amphoteric metals (Pb and Zn) were obtained, and have been compared with those of single batch extraction of toxic characteristic leaching procedure (TCLP). In each size fraction of baghouse ash or scrubber residue, lead or zinc shows a common phenomena that the TCLP value is always lower than the content of the water‐soluble fraction. For lead, baghouse ash has a significant size‐dependent distribution on the water‐soluble phase to perform a size‐dependent test of lead in the TCLP test. The zinc TCLP data having less size dependence might be due to that neither the baghouse ash nor the scrubber residue has a size‐dependent distribution on the water‐soluble zinc phase.     

Irradiation-induced reduction and luminescence properties of Sm doped in BaBPO5

Usually, Sm²⁺ ions could be reduced by heating the materials in reducing atmospheres. Exposure to ionizing radiations is also known to cause Sm³⁺→Sm²⁺ conversion. In this work, BaBPO₅ doped with the samarium ion was prepared by high temperature solid-state reaction. Sm²⁺ ions were obtained by two different reduction methods, i.e., heating in H₂ reduced atmosphere and X-ray irradiation. The measurements of X-ray diffraction (XRD), and scanning electron microscope (SEM) were investigated. It is found that the conversion of Sm³⁺→Sm²⁺ is very efficient in BaBPO₅ hosts after X-ray irradiation. Sm²⁺ ions under these two reduction methods exhibit different characteristics that were studied by measurements of luminescence and decay. The results showed that the luminescence properties of Sm²⁺ ions in BaBPO₅ were highly dependent on the sample preparation conditions.     

Codes Over the p-adic Integers

We study codes over the p-adic integers and correct errors in the existing literature. We show that MDS codes exist over the p-adics for all lengths, ranks and p. We show that self-dual codes exist over the 2-adics if and only if the length is a multiple of 8 and that self-dual codes exist over the p-adics with p odd if and only if the length is 0 (mod 4) for p ≡ 3 (mod 4) and 0 (mod 2) for p ≡ 1 (mod 4).     

Divinylsiloxane‐bisbenzocyclobutene‐based polymer modified with polystyrene–polybutadiene–polystyrene triblock copolymers

Divinylsiloxane‐bisbenzocyclobutene (DVS‐bisBCB) polymer has very low dielectric constant and dissipation factor, good thermal stability, and high chemical resistance. The fracture toughness of the thermoset polymer is moderate due to its high crosslink density. A thermoplastic elastomer, polystyrene–polybutadiene–polystyrene triblock copolymer, was incorporated into the matrix to enhance its toughness. The cured thermoset matrix showed different morphology when the elastomer was added to the B‐staged prepolymer or when the elastomer was B‐staged with the DVS‐bisBCB monomer. Small and uniformly distributed elastomer domains were detected by transmission electron micrographs (TEM) in the former case, but TEM did not detect a separate domain in the latter case. A high percentage of the polystyrene–polybutadiene–polystyrene triblock copolymer could be incorporated into the DVS‐bisBCB thermoset matrix by B‐staging the triblock copolymer with the BCB monomer. The elastomer increased the fracture toughness of DVS‐bisBCB polymer as indicated by enhanced elongation at break and increased K1c values obtained by the modified edge‐lift‐off test. Elastomer modified DVS‐bisBCB maintained excellent electrical properties, high T_g and good thermal stability, but showed higher coefficient of linear thermal expansion values. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1591–1599, 2006     

Effects of the architecture and environment on polymeric molecular assemblies of novel amphiphilic diblock copolynorbornenes with narrow polydispersity via living ring‐opening metathesis polymerization

Diblock copolymers of 5‐(methylphthalimide)bicyclo[2.2.1]hept‐2‐ene (NBMPI) and 1,5‐cyclooctadiene were synthesized by living ring‐opening metathesis polymerization with a well‐defined catalyst {RuCl₂(CHPh)[P(C₆H₁₁)₃]₂}. Unhydrogenated diblock copolymers showed two glass transitions due to poly(NBMPI) and polybutadiene segments, such as two glass‐transition temperatures at ?86.5 and 115.3 °C for poly 1a and ?87.2 and 115.3 °C for poly 1b . However, only one melting temperature could be observed for hydrogenated copolymers, such as 119.8 °C for poly 2a and 121.7 °C for poly 2b . The unhydrogenated diblock copolymer with the longer poly(NBMPI) chain (poly 1a ; temperature at 10% mass loss = 400 °C) exhibited better thermal stability than the one with the shorter poly(NBMPI) chain (poly 1b ; temperature at 10% mass loss = 385 °C). Two kinds of hydrogenated diblock copolymers, poly 2a and poly 2b , exhibited relatively poor solubility but better thermal stability than unhydrogenated diblock copolymers because of the polyethylene segments. Poly[(hydrochloride quaternized 2‐norbornene‐5‐methyleneamine)‐b‐butadiene]‐1 (poly 3a ) was obtained after the hydrolysis and quaternization of poly 1a . Dynamic light scattering measurements indicated that the hydrodynamic diameters of the cationic copolymer (poly 3a ) in water (hydrodynamic diameter = 1580 nm without salt), methanol/water (4/96 v/v; hydrodynamic diameter = 1500 nm without salt), and tetrahydrofuran/water (4/96 v/v; hydrodynamic diameter = 1200 nm without salt) decreased with increasing salt (NaCl) concentration. The effect of temperature on the hydrodynamic diameter of hydrophobically modified poly 3a was also studied. The inflection point of the hydrodynamic diameter of poly 3a was observed at various polymer concentrations around 30 °C. The critical micelle concentration of hydrophobically modified poly 3a was observed at 0.018 g dL^?1. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2901–2911, 2006