α-钛合金TA6的动态力学性能和剪切现象分析

诸多文献已经报道了β和(α β)钛合金冲击和爆炸加载下的绝热剪切现象,本文利用分离式的Hopkinson压杆和反射式Hopkinson拉杆对α-钛合金TA6的动态力学性能进行研究,得到不同应变率下材料的应力-应变曲线,发现钛合金TA6和其他钛合金一样也是一种应变率敏感材料。冲击拉伸加载时破坏形状45度剪切断口,然而其在冲击压缩应力作用下体现为典型的韧性,并未出现其它类型钛合金通常会出现的绝热剪切破坏。进一步分析表明:α-钛合金TA6不同于β和(α β)的钛合金,α-钛合金TA6相对于β和(α β)的钛合金是一种绝热剪切不敏感的材料。同时也利用应力状态的柔韧系数的概念对拉伸时45度的剪切断口解释。     

三维非线性有限元与弹性边界元耦合数值方法

本文系统地讨论了以下三个问题:(1) 有限元与边界元耦合中的几个数值问题,其中包括:边界积分方程的凝聚、等效刚度矩阵的对称化及面力不连续的处理;(2) 弹塑性有限元与弹性边界元的耦合;(3) 弹粘塑性有限元与弹性边界元的耦合及数值计算稳定性条件。     

Highly Efficient InBr3 Catalyzed Michael Addition of Indoles to α, β-Unsaturated Esters

A highly efficient synthetic strategy toward Michael addition of indoles to α,β‐unsaturated esters has been developed using Lewis acid InBr₃ as catalyst. The reactions generated 3‐substituted indoles in high yields with excellent regio‐selectivity in the presence of catalytic amount of InBr₃ under mild reaction conditions. The method is simple, efficient and practical.     

BaCe_(0.8-x)Nb_xGd_(0.2)O_(3-δ)(0≤x≤0.45)的制备及性能研究

采用高温固相反应法制备了质子导体BaCe0.8-xNbxGd0.2O3-δ(0≤x≤0.45)。结合XRD、SEM、EIS等技术对其物相、微观形貌、稳定性及电导率进行了研究。结果表明,在1600℃烧结5h制备的质子导体BaCe0.8-xNbxGd0.2O3-δ(0≤x≤0.45)均能保持主相为斜方晶的钙钛矿结构。Nb的加入可明显提高烧结样品的致密性及在CO2和水蒸气气氛下的稳定性。在湿润H2/Ar(0.4%,V/V)气氛中800℃下,x=0.1样品的电导率为5.73mS·cm-1,电导活化能为0.35eV,与x=0的样品相当。     

Application of in-plasma catalysis and post-plasma catalysis for methane partial oxidation to methanol over a Fe2O3-CuO/γ-Al2O3 catalyst

Methane partial oxidation to methanol (MPOM) using dielectric barrier discharge over a Fe2O3-CuO/γ-Al2O3 catalyst was performed. The multicomponent catalyst was combined with plasma in two different configurations, i.e., in-plasma catalysis (IPC) and post-plasma catalysis (PPC). It was found that the catalytic performance of the catalysts for MPOM was strongly dependent on the hybrid configuration. A better synergistic performance of plasma and catalysis was achieved in the IPC configuration, but the catalysts packed in the discharge zone showed lower stability than those connected to the discharge zone in sequence. Active species, such as ozone, atomic oxygen and methyl radicals, were produced from the plasma-catalysis process, and made a major contribution to methanol synthesis. These active species were identified by the means of in situ optical emission spectra, ozone measurement and FT-IR spectra. It was confirmed that the amount of active species in the IPC system was greater than that in the PPC system. The results of TG, XRD, and N2 adsorption-desorption revealed that carbon deposition on the spent catalyst surface was responsible for the catalyst deactivation in the IPC configuration.     

The detection of tetrahydrofuran hydrate formation and saturation using magnetic resonance imaging technique

Tetrahydrofuran (THF) hydrate was formed in bulk as well as in glass beads pack with a mean diameter of 3.0 mm by controlling the temperature under ambient pressure. Images of THF hydrate formation procedure were obtained using the magnetic resonance imaging (MRI) technique. The experiment results showed that MRI is an effective method for the detection of hydrate formation. Saturation of hydrate formed both in bulk and glass beads can be confirmed by intensity integration of MRI images.     

载体对Cu基催化剂富氢条件下CO氧化性能的影响

燃料电池是一种高效和环境友好的能源装置,其中质子交换膜燃料电池（PEMFC）以其工作温度低、低温启动性能好、功率密度和能量转换效率高等优点而广受关注[1].目前,PEMFC所需要的氢气一般通过醇或烃类的重整获得,但所得的氢气含有浓度较高的、使燃料电池Pt电极中毒的CO,导致电池失效,CO的选择性（优先）催化氧化（PROX）在众多去除CO的方法中被认为是最直接有效的一种.     

左氧氟沙星-Al~(3+)-十二烷基硫酸钠体系胶束体系分光光度法测定左氧氟沙星

在B-R缓冲介质中,十二烷基硫酸钠(SDS)对左氧氟沙星(LVFX)-Al3+体系有显著的增敏作用,以此为基础建立了利用SDS增敏分光光度法测定LVFX的新方法。研究表明,体系吸光度与LVFX浓度在0.2~10μg/mL范围内呈良好的线性关系,相关系数r=0.9993,检出限为0.096μg/mL。将该方法用于盐酸左氧氟沙星片剂的测定,结果满意。     

膦系阻垢剂阻碳酸钙垢机理的研究

在模拟循环水中, 通过静态阻垢实验研究了HEDP, PBTCA, ATMP和EDTMP对碳酸钙的阻垢性能, 在相同的加药浓度下(按物质的量浓度计)阻垢性能的强弱顺序为HEDP＞PBTCA＞ATMP＞EDTMP; 同时采用分子动力学方法, 模拟计算了阻垢剂负二价离子与方解石(104), (102), (202)和(113)面的相互作用. 结果表明: 阻垢剂分子中的膦酸基团和羧酸基团与碳酸钙中的Ca^2＋形成的离子键对吸附起到了主要作用, 同时阻垢剂与晶面间存在较弱的范德华力相互作用. 阻垢剂与各晶面的结合能强弱顺序为(113)≥(102)≥(202)＞(104); 分子中的羟基易与垢晶面形成氢键而加强阻垢效果; 羧基的位置不同对阻垢作用的影响不同. 将静态阻垢的实验结果与分子动力学模拟结果进行了相关性分析, 发现阻垢剂在(104)面和(102)面上的吸附对阻垢作用的贡献较大.     

Thermoresponsive copolymer nanofilms for controlling cell adhesion, growth, and detachment

This study reports the development and use of a novel thermoresponsive polymeric nanofilm for controlling cell adhesion and growth at 37 °C, and then cell detachment for cell recovery by subsequent temperature drop to the ambient temperature, without enzymatic cleavage or mechanical scraping. A copolymer, poly(N-isopropylacrylamide-co-hydroxypropyl methacrylate-co-3-(trimethoxysilyl)propyl methacrylate) (abbreviated PNIPAAm copolymer), was synthesized by free radical polymerization. The thermoresponses of the copolymer in aqueous solution were demonstrated by dynamic light scattering (DLS) through detecting the sensitive changes of copolymer aggregation against temperature. The DLS measurements revealed the lower critical solution temperature (LCST) at approximately 30 °C. The PNIPAAm film stability and robustness was provided through silyl cross-linking within the film and with the hydroxyl groups on the substrate surface. Film thickness, stability, and reversibility with respect to temperature switches were examined by spectroscopic ellipsometry (SE), atomic force microscopy (AFM), and contact angle measurements. The results confirmed the high extent of thermosensitivity and structural restoration based on the alterations of film thickness and surface wettability. The effective control of adhesion, growth, and detachment of HeLa and HEK293 cells demonstrated the physical controllability and cellular compatibility of the copolymer nanofilms. These PNIPAAm copolymer nanofilms could open up a convenient interfacial mediation for cell film production and cell expansion by nonenzymatic and nonmechanical cell recovery.