光突发交换的交换控制策略和光缓存配置

光突发交换是面向下一代互联网的光交换模式.讨论了异步光突发交换系统的交换控制策略以及相应光缓存的优化配置策略.除了传统预约模式的交换策略,还研究了非预约和改进型预约模式,它们的性能评估由计算机仿真给出.结果表明:在条件相当情况下,改进型预约模式具有最低的丢包率.同时光缓存的配置对上述几类交换控制策略的性能都有很大影响,仿真结果指出:光缓存的粒度对系统性能具有重要影响,所讨论的几类交换模式都存在最佳时延粒度,研究结果对光交换矩阵的设计有指导意义.     

合作联盟资源集成计划一种新方法

合作联盟里，资源集成计划往往是联盟成员群体谈判博弈的结果。本以两人博弈为例，对联盟的资源集成计划给出一个谈判博弈模型，能够较好地模仿和反映合作联盟资源整合计划的制订过程。     

温度对PSⅡCP4 7/D1/D2/Cytb559复合物荧光光谱特性的影响

采用激励光源为514.5 nm的分幅扫描单光子计数荧光光谱装置对经20℃、42℃和48℃不同温度处理后的反应中心复合物CP47/D₁/D₂/Cyt b559的荧光光谱特性进行了研究.经解析,获得不同温度处理后,CP47/D₁/D₂/Cyt b559复合物最大峰值未发生变化,均在682 nm,说明Chla670的能量都由Chla682接收,但损耗愈来愈小,在48℃时,损耗程度最小,而其荧光百分比未发生多大变化.振动副带～700 nm和～740 nm的中心波长都发生蓝移,在不同温度下分别为:20℃ 703 nm,749 nm;42℃ 697 nm,744 nm;48℃ 694 nm,740 nm.因此可以推测温度的升高,影响了CP47/D₁/D₂/Cyt b559色素蛋白的二级结构以及色素分子的空间位置,使最大峰值处的荧光强度逐渐降低,振动副带逐渐蓝移.42℃的温度已造成影响,48℃影响较大.     

利用场发射显微镜研究O2对单壁碳纳米管场发射的影响

利用场发射显微镜和四极质谱计研究了充入高纯O2的四极质谱和O2对单壁碳纳米管场发射的影响.单壁碳纳米管经过约1000℃的热处理得到清洁态场发射像后，充入O2，分别测量了O2吸附和脱附后场发射的I V特性.实验观测到在单壁碳纳米管上O2的吸附使场发射电流减小，说明逸出功增加.在10-4Pa的O2压强下对单壁碳纳米管进行约1000℃的热处理，可以产生氧化刻蚀作用，观测到场发射像的变化，并测量了氧化刻蚀产生的I V特性变化. 关键词： 单壁碳纳米管 场发射显微镜 场发射 四极质谱     

成分和厚度的依赖

通过调整Mn的成分，系统地研究了Ni81Fe19/Ni100-xMnx双层膜的磁学性质，特别是交换偏置场(Hex)的变化.当Ni100-xMnx中Mn的原子百分比在534%到600%之间时，对于150nm的Ni81Fe19，得到了最大的交换偏置场175kA/m，同时由于Mn对Ni81Fe19层的扩散所造成的磁矩的降低小于20%；高角x射线衍射证明Ni100-xMnx的晶格常数随着Mn成分的改变而变化，Mn含量越多，其晶格常数越大；制备态Ni100-xMnx膜晶格常数与θ相NiMn膜晶格常数的接近程度与NiMn膜θ相形成的容易程度相对应.也研究了交换偏置场随着Ni１００-xMnx厚度的变化，第一次得到了当Ni100-xMnx中Mn的原子百分比为706%时，Ni81Fe19(150nm)/Ni100-xMnx(90nm)双层膜在经过240℃，5h退火后，可以有80kA/m的交换偏置场，此时铁磁层磁矩的大小几乎不变. 关键词： Ni81Fe19/Ni100-xMnx 交换偏置场     

Spectral Anomalies in the Fraunhofer Diffraction Pattern

We study the spectral characteristics theoretically and experimentally in the Fraunhofer diffraction pattern formed by the diffraction of a spatially coherent, polychromatic light through a slit. It is found that the spectrum in some diffraction directions close to the singular direction is redshifted, compared to the spectrum of the incident polychromatic light, and blueshifted in other directions, and splits into two lines at the singular direction. We show that the experimental results are consistent with the theoretical expectations.     

社会经济管理系统和谐性模型的构建与分析

本文从非线性自然观的视野。引用与分析了社会经济系统功能模型与效应模型。构建了系统和谐状态模型与和谐状态可信度模型，形象地说明了企业系统的和谐既是一个随机不确定状态。又是企业和谐力量与不和谐力量相互抗争干涉的过程。依据协同学原理提出了企业系统和谐演进的机制，表明企业系统的和谐发展是子系统和谐协同的过程。即子系统竞争合作的过程。文中所构建的模型，从理论上清晰地说明了企业系统和谐有序运行的机理，为如何构建和谐企业。提供了建设性的思考。     

Dendrimers as scaffolds for multifunctional reversible addition–fragmentation chain transfer agents: Syntheses and polymerization

The synthesis and characterization of novel first‐ and second‐generation true dendritic reversible addition–fragmentation chain transfer (RAFT) agents carrying 6 or 12 pendant 3‐benzylsulfanylthiocarbonylsulfanylpropionic acid RAFT end groups with Z‐group architecture based on 1,1,1‐hydroxyphenyl ethane and trimethylolpropane cores are described in detail. The multifunctional dendritic RAFT agents have been used to prepare star polymers of poly(butyl acrylate) (PBA) and polystyrene (PS) of narrow polydispersities (1.4 < polydispersity index < 1.1 for PBA and 1.5 < polydispersity index < 1.3 for PS) via bulk free‐radical polymerization at 60 °C. The novel dendrimer‐based multifunctional RAFT agents effect an efficient living polymerization process, as evidenced by the linear evolution of the number‐average molecular weight (M_n) with the monomer–polymer conversion, yielding star polymers with molecular weights of up to M_n = 160,000 g mol^?1 for PBA (based on a linear PBA calibration) and up to M_n = 70,000 g mol^?1 for PS (based on a linear PS calibration). A structural change in the chemical nature of the dendritic core (i.e., 1,1,1‐hydroxyphenyl ethane vs trimethylolpropane) has no influence on the observed molecular weight distributions. The star‐shaped structure of the generated polymers has been confirmed through the cleavage of the pendant arms off the core of the star‐shaped polymeric materials. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5877–5890, 2004     

Synthesis and characterization of well‐defined diblock and triblock copolymers of poly(N‐isopropylacrylamide) and poly(ethylene oxide)

Well‐defined diblock and triblock copolymers composed of poly(N‐isopropylacrylamide) (PNIPAM) and poly(ethylene oxide) (PEO) were successfully synthesized through the reversible addition–fragmentation chain transfer polymerization of N‐isopropylacrylamide (NIPAM) with PEO capped with one or two dithiobenzoyl groups as a macrotransfer agent. ¹H NMR, Fourier transform infrared, and gel permeation chromatography instruments were used to characterize the block copolymers obtained. The results showed that the diblock and triblock copolymers had well‐defined structures and narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight < 1.2), and the molecular weight of the PNIPAM block in the diblock and triblock copolymers could be controlled by the initial molar ratio of NIPAM to dithiobenzoate‐terminated PEO and the NIPAM conversion. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4873–4881, 2004     

Exploitation of introducing of catalytic centers into layer galleries of layered silicates and related epoxy nanocomposites. I. Epoxy nanocomposites derived from montmorillonite modified with catalytic surfactant‐bearing carboxyl groups

Montmorillonite (MMT) was modified with the acidified cocamidopropyl betaine (CAB) and the resulting organo‐montmorillonite (O‐MMT) was dispersed in an epoxy/methyl tetrahydrophthalic anhydride system to form epoxy nanocomposites. The intercalation and exfoliation behavior of the epoxy nanocomposites were examined by X‐ray diffraction and transmission electron microscopy. The curing behavior and thermal property were investigated by in situ Fourier transform infrared spectroscopy and DSC, respectively. The results showed that MMT could be highly intercalated by acidified CAB, and O‐MMT could be easily dispersed in epoxy resin to form intercalated/exfoliated epoxy nanocomposites. When the O‐MMT loading was lower than 8 phr (relative to 100 phr resin), exfoliated nanocomposites were achieved. The glass‐transition temperatures (T_g's) of the exfoliated nanocomposite were 20 °C higher than that of the neat resin. At higher O‐MMT loading, partial exfoliation was achieved, and those samples possessed moderately higher T_g's as compared with the neat resin. O‐MMT showed an obviously catalytic nature toward the curing of epoxy resin. The curing rate of the epoxy compound increased with O‐MMT loading. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1192–1198, 2004