Color-stable,reduced efficiency roll-off hybrid white organic light emitting diodes with ultra high brightness

High-brightness and color-stable two-wavelength hybrid white organic light emitting diodes (HWOLEDs) with the configuration of indium tin oxide (ITO)/ N, N, N, N-tetrakis(4-methoxyphenyl)-benzidine (MeO-TPD): tetrafluoro-tetracyanoqino dimethane (F4-TCNQ)/N,N-di(naphthalene-1-yl)-N,N-diphenyl-benzidine (NPB)/ 4,4-N,N-dicarbazolebiphenyl (CBP): iridium (III) diazine complexes (MPPZ) 2 Ir(acac)/NPB/2-methyl-9,10-di(2-naphthyl)anthracene (MADN): p-bis(p-N,N-di-phenyl-aminostyryl)benzene (DSA-ph)/bis(10-hydroxybenzo[h] quino-linato)beryllium complex (Bebq2)/LiF/Al have been fabricated and characterized. The optimal brightness of the device is 69932 cd/m2 at a voltage of 13 V, and the Commission Internationale de l'Eclairage (CIE) chromaticity coordinates are almost constant during a large voltage change of 6-12 V. Furthermore, a current efficiency of 15.3 cd/A at an illumination-relevant brightness of 1000 cd/m2 is obtained, which rolls off slightly to 13.0 cd/A at an ultra high brightness of 50000 cd/m2. We attribute this great performance to wisely selecting an appropriate spacer together with effectively utilizing the combinations of exciton-harvested orange-phosphorescence/blue-fluorescence in the device. Undoubtedly, this is one of the most exciting results in two-wavelength HWOLEDs up to now.     

Influence of focusing depth on the microfabrication of waveguides inside silica glass by femtosecond laser direct writing

We studied the influence of focusing depth on the index change threshold and damage threshold of silica glass irradiated by a focused 120 fs laser beam. Both thresholds increased with the focusing depth. The aspect ratio of the waveguide cross section can be selected by changing the focusing depth. A 5 mm long waveguide was written at the depth of 2100 μm, which was single mode at 632.8 nm and exhibited propagation loss of 0.56 dB/cm. The refractive index change was calculated to be ∼2.47×10^-3. The influence of the focusing depth should be considered in multi-layer devices as shown in the fabrication of a 3×3 waveguide array. PACS 42.62.-b; 42.82.Et; 81.05.Kf     

Controlling a bunch of multiple filaments by means of a beam diameter

We demonstrate a three orders of magnitude increase and stability in the backscattered fluorescence signal from nitrogen molecules by terawatt femtosecond laser pulse induced air filaments using a new method. The method is based on squeezing the initial beam diameter using a telescope. The effect of laser shot-to-shot fluctuations was included in numerical simulations by a random distribution of the initial intensity in both squeezed and non-squeezed beams. Statistical processing of the simulation results shows that the average diameter of plasma channels as well as the total amount of free electrons generated in a bunch of multiple filaments in air is larger in the squeezed beam. Shot-to-shot stability of the simulated plasma density increases in the squeezed beam. The change of this plasma density with propagation distance is in good qualitative agreement with the change of the range-corrected nitrogen fluorescence signal with distance. PACS 42.65.Jx; 42.60.Jf; 42.68.Ay; 42.68.Wt     

Synthesis and magnetic properties of multilayer Ni/Cu and NiFe/Cu nanowires

Highly ordered composite nanowires with multilayer Ni/Cu and NiFe/Cu have been fabricated by pulsed electrodeposition into nanoporous alumina membrane. The diameter of wires can be easily varied by pore size of alumina, ranging from 30 to 100 nm. The applied potential and the duration of each potential square pulse determine the thickness of the metal layers. The nanowires have been characterized by transmission electron microscopy (TEM), magnetic force microscopy (MFM), and vibrating sample magnetometer (VSM) measurements. The MFM images indicate that every ferromagnetic layer separated by Cu layer was present as single isolated domain-like magnet. This technique has potential use in the measurement and application of magnetic nanodevices.     

Multiwavelength Raman fiber lasers with equalized peak power using a sampled chirped fiber Bragg grating

Two novel multiwavelength Raman fiber lasers using a ring cavity and a linear cavity are proposed and demonstrated experimentally. Both laser configurations include a sampled chirped fiber Bragg grating used in the reflection mode. By adjusting the polarization controller (PC) in the cavities, up to ten stable lasing wavelengths with 0.8 nm spacing and equalized peak power are achieved at room temperature. It is observed that the output spectrum depends upon which port of the grating is connected to the cavity. These two fiber ring lasers offer advantages such as, stable room temperature operation, simple structure, low loss, multiwavelength lasing lines with moderate output power. PACS 42.55.Wd; 42.55.Ye; 42.81.-i     

Q-switched and mode-locked diode-pumped Nd:YAG laser with an LT-GaAs

Simultaneous Q-switching and mode-locking (QML) is accomplished in a diode-pumped Nd:YAG laser using low-temperature GaAs (LT-GaAs) as the saturable absorber, which also acts as an output coupler at the same time. The repetition rate of the Q-switched envelope increased from 25 to 40 kHz as the pump power increased from 2.2 to 6.9 W. The mode-locked pulses inside the Q-switched pulse envelope had a repetition rate of 714 MHz. A maximum average output power of 770 mW was obtained.     

Laser ranging based on electro-optic switch

Based on electro-optic switch effect in crystal, a novel laser ranging method is proposed. CW-laser emitted by laser transmitter propagates forward to the measured target, after being reflected by the target, and then goes back to the transmitter. Close to the transmitter, a special mono-block LiNbO₃ crystal is added into the round-trip light beams. High-voltage pulses with the sharp enough changes in rising edges are loaded on the crystal. Based on electro-optic effect, double refraction and internal double reflection effect in crystal, the crystal cuts off the round-trip light beams, and reflects a light pulse cut out by the crystal to a detector aside from the original beam path. The pulse width T is the period that laser propagates forward and back between the crystal and the target. The feasibility of the new idea is proved by our experiments and a brand-new way for the laser ranging is provided.     

Effect of magnetic field on the TC and magnetic properties for the aligned MnBi compound

In the compound MnBi, a first-order transition from the paramagnetic to the ferromagnetic state can be triggered by an applied magnetic field and the Curie temperature increases nearly linearly with an increase in magnetic field by ∼2 K/T. Under a field of 10 T, T_C increases by 20 and 22 K during heating and cooling, respectively. Under certain conditions a reversible magnetic field or temperature induced transition between the paramagnetic and ferromagnetic states can occur. A magnetic and crystallographic H-T phase diagram for MnBi is given. Magnetic properties of MnBi compound aligned in a Bi matrix have been investigated. In the low temperature phase MnBi, a spin-reorientation takes place during which the magnetic moments rotate from being parallel to the c-axis towards the basal plane at ∼90 K. A measuring Dc magnetic field applied parallel to the c-axis of MnBi suppresses partly the spin-reorientation transition. Interestingly, the fabricated magnetic field increases the temperature of spin-reorientation transition T_s and the change in magnetization for MnBi. For the sample solidified under 0.5 T, the change in magnetization is ∼70% and T_s is ∼91 K.     

Study on anti-emission materials for non-emitting grid applications in microwave power tubes

Hafnium and platinum were deposited onto molybdenum grids by ion-beam assisted deposition method. Electron-emission characteristics from molybdenum grids with Hf and Pt films, which were contaminated by active electron-emission substances (Ba, BaO) of the cathode, were measured using analogous diode method. The surfaces of grids were analyzed by X-ray diffraction. The results revealed that the reaction between BaO and Hf formed BaHfO₃ compound, which greatly reduced the accumulation of BaO on the surface and accordingly decreased grid emission. In contrast, Ba were formed by the decomposition of BaO on the surface of Pt film under high temperature and re-evaporated from its surface, which reduced the active electron-emission substances on the surface of the grid and effectively restrained grid emission. Their mechanisms for grid-emission suppression are discussed and a good method to develop new grid-coating materials is suggested.     

High-throughput screening of fuel cell electrocatalysts

The drawbacks of our earlier report of preparing fuel cell catalyst arrays by borohydride reduction of inkjet prepared arrays of metal salts are discussed along with the need for inclusion of state-of-the-art metrics in all array screening. An alternative method for screening of hydrogen/air cathode catalysts, direct methanol fuel cell (DMFC) anode catalysts, and catalyst loading studies is provided. State-of-the-art Johnson Matthey catalysts were used in control experiments to demonstrate the utility of the array fuel cell for high throughput screening of fuel cell catalysts in the 3-4 mg/cm² range. This report lays out hard learned rules for high throughput screening and demonstrates that the array fuel cell can be used for very precise screening of libraries of membrane electrode assembly (MEA) components without the pitfalls discussed in the introduction.