Preparation of antimicrobial poly(vinyl alcohol) nanofibers containing silver nanoparticles

Polyvinyl alcohol (PVA) nanofibers containing Ag nanoparticles were prepared by electrospinning PVA/silver nitrate (AgNO₃) aqueous solutions, followed by short heat treatment, and their antimicrobial activity was investigated for wound dressing applications. Since PVA is a water soluble and biocompatible polymer, it is one of the best materials for the preparation of wound dressing nanofibers. After heat treatment at 155 °C for 3 min, the PVA/AgNO₃ nanofibers became insoluble, while the Ag⁺ ions therein were reduced so as to produce a large number of Ag nanoparticles situated preferentially on their surface. The residual Ag⁺ ions were reduced by subsequent UV irradiation for 3 h. The average diameter of the Ag nanoparticles after the heat treatment was 5.9 nm and this value increased slightly to 6.3 nm after UV irradiation. It was found that most of the Ag⁺ ions were reduced by the simple heat treatment. The PVA nanofibers containing Ag nanoparticles showed very strong antimicrobial activity. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2468–2474, 2006     

WAXS studies on block copolymers of ethylene and propylene

Wide-angle X-ray scattering from presumed block copolymers of polypropylene (PP) and ethylene-propylene copolymer (EPR), i.e., PP-EPR and PP-EPR-PP, synthesized by sequential polymerization with δ-TiCl₃? Et₂AlCl, was examined and compared with WAXS of mechanical blends and chain-transfer mixtures of PP and EPR with comparable compositions. The peak at 2θ = 20° for both the copolymers and the mixtures was attributed to the γ modification of PP in EPR. A strong variation in the ratio of diffraction intensities I₀₄₀/I₁₁₀ of PP in block copolymers and mixtures was explained in terms of crystallite growth in different directions. Analysis of the patterns and calculation of crystallinity, crystallite size, and lattice parameters led to the conclusion that block structure existed in the prepared copolymers.     

In‐line monitoring of UV photopolymerization with a quartz crystal resonator

An in‐line monitoring device using a quartz crystal resonator for thin film polymerization was proposed, and its performance has been evaluated by implementing in the UV polymerization of 2‐hydroxyethyl methacrylate with a photoinitiator of 1‐chloroanthraquinone. Because the variation of resonant resistance of the resonator is proportional to the square root of viscosity change that is closely related to the polymerization degree, the resistance can be used as a measure of the polymerization degree. The resistance measurements were compared with the outcome of instrumental analyses of polymerization degree using an FTIR spectrometer and a gel permeation chromatograph. The experimental results showed that the resistance measurements were consistent with the experimental outcome of the instrumental analyses, and this indicates the effectiveness of the proposed device. Owing to the simplicity and availability of the resonator system, its wide utilization in the monitoring of a variety of film polymerization processes, including photoresistor application, is expected. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2428–2439, 2006     

A copper‐based reverse atom‐transfer radical polymerization process for the living radical polymerization of polyacrylonitrile

The reverse atom‐transfer radical polymerization (RATRP) technique using CuCl₂/2,2′‐bipyridine (bipy) complex as a catalyst was applied to the living radical polymerization of acrylonitrile (AN). A hexasubstituted ethane thermal iniferter, diethyl 2,3‐dicyano‐2,3‐diphenylsuccinate (DCDPS), was firstly used as the initiator in this copper‐based RATRP initiation system. A CuCl₂ to bipy ratio of 0.5 not only gives the best control of molecular weight and its distribution, but also provides rather rapid reaction rate. The rate of polymerization increases with increasing the polymerization temperature, and the apparent activation energy was calculated to be 57.4 kJ mol^?1. Because the polymers obtained were end‐functionalized by chlorine atoms, they were used as macroinitiators to proceed the chain extension polymerization in the presence of CuCl/bipy catalyst system via a conventional ATRP process. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 226–231, 2006     

Synthesis of polyacrylonitrile via reverse atom transfer radical polymerization catalyzed by FeCl3/isophthalic acid

FeCl₃ coordinated by isophthalic acid was first used as a catalyst in the azobisisobutyronitrile‐initiated reverse atom transfer radical polymerization of acrylonitrile. N,N‐Dimethylformamide was used as a solvent to improve the solubility of the ligand. An FeCl₃‐to‐isophthalic acid ratio of 0.5 not only gave the best control of the molecular weight and its distribution but also provided rather a rapid reaction rate. The effects of different solvents on the polymerization of acrylonitrile were also investigated. The rate of the polymerization in N,N‐dimethylformamide was faster than that in propylene carbonate and toluene. The molecular weight of polyacrylonitrile agreed reasonably well with the theoretical molecular weight in N,N‐dimethylformamide. The rate of polymerization increased with increasing polymerization temperature, and the apparent activation energy was calculated to be 59.9 kJ mol^?1. Reverse atom transfer radical polymerization was first used to successfully synthesize acrylonitrile polymers with a molecular weight higher than 80,000 and a narrow polydispersity as low as 1.22. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 219–225, 2006     

Measurement and prediction of solubilities and diffusion coefficients of carbon dioxide in starch–water mixtures at elevated pressures

The solubility and diffusion coefficient of carbon dioxide in intermediate‐moisture starch–water mixtures were determined both experimentally and theoretically at elevated pressures up to 16 MPa at 50 °C. A high‐pressure decay sorption system was assembled to measure the equilibrium CO₂ mass uptake by the starch–water system. The experimentally measured solubilities accounted for the estimated swollen volume by Sanchez–Lacombe equation of state (S‐L EOS) were found to increase almost linearly with pressure, yielding 4.0 g CO₂/g starch–water system at 16 MPa. Moreover, CO₂ solubilities above 5 MPa displayed a solubility increase, which was not contributed by the water fraction in the starch–water mixture. The solubilities, however, showed no dependence on the degree of gelatinization (DG) of starch. The diffusion coefficient of CO₂ was found to increase with concentration of dissolved CO₂, which is pressure‐dependent, and decrease with increasing DG in the range of 50–100%. A free‐volume‐based diffusion model proposed by Areerat was employed to predict the CO₂ diffusivity in terms of pressure, temperature, and the concentration of dissolved CO₂. S‐L EOS was once more used to determine the specific free volume of the mixture system. The predicted diffusion coefficients showed to correlate well with the measured values for all starch–water mixtures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 607–621, 2006     

Acetic anhydride as a synthetic reagent

Acetic anhydride has been used widely in synthetic organic chemistry, especially in syntheses and transformations of heterocyclic compounds. These utilities are reviewed under the following classification.     

Single Atom Alloy Preparation and Applications in Heterogeneous Catalysis

There have been remarkable progresses in manipulating heterogeneous catalysts' nanostructures in the past decade. The concept of single atom alloy (SAA) was firstly proposed in 2012 when researchers successfully stabilized single Pd atoms on the Cu(111) surface. However, earlier work in 2009, which focused on replacing one Au atom with a Pd atom in thiolate protected Au₂₅ nanoclusters, could also be considered as the pioneer work of single atom alloy. Both kinds of single atom alloys exhibited the potential of maximum utilization of scarce elements and attractive catalytic performances. The well‐defined structures of SAA catalysts make accurate modeling possible, which further realizes the rational design of single atom alloy catalysts. In this review, we summarize the research trajectory of single atom alloys as well as recent achievements in this field. We also introduce several commonly adopted characterization methods for SAA catalysts such as scanning tunneling microscopy (STM), temperature programmed reaction (TPR), extended X‐ray absorption fine structure (EXAFS) spectra, matrix assisted laser desorption/ionization mass spectrum (MALDI‐MS) and differential pulse voltammetry (DPV). Through discussing recent progresses in SAA catalysts, we propose that future researches in this filed should be focused on exploring new kinds of metal nanocrystals and controlling the nanostructure of SAA even more precisely.     

Density functional study of the l-proline-catalyzed α-aminoxylation of aldehydes reaction: The reaction mechanism and selectivity

The reaction mechanism of the l-proline-catalyzed α-aminoxylation reaction between aldehyde and nitrosobenzene has been investigated using density functional theory (DFT) calculation. Our calculation results reveal following conclusions [1]. The first step that corresponds to the formation of C–O bond, is the stereocontrolling and rate-determining step [2]. Among four reaction channels, the syn-attack reaction channel is more favorable than that of the anti one, and the TS-ss channel dominates among the four channels for this reaction in the step of C–O bond formation [3]. The intermolecular hydrogen bond between the acidic hydrogen of l-proline and the N atom of the nitrosobenzene in an early stage of the process catalyzes very effectively the C–O bond formation by a large stabilization of the negative charge that is developing at the O atom along the electrophilic attack [4]. The effect of solvent decreases the activation energy, and also, the calculated energy barriers are decrease with the enhancement of dielectric constants for C–O bond formation step. These results are in good agreement with experiment, and allow us to explain the origin of the catalysis and stereoselectivity for l-proline-catalyzed α-aminoxylation of aldehyde reaction. The addition of H₂O to substituted imine proline, intermolecular proton-transfer steps, and the l-proline elimination process were also studied in this paper.