Time-resolved synchrotron X-ray study of crystalline phase transition in poly(aryl ether ketone ketone) containing alternated terephthalic/isophthalic moieties

Unique crystallization and melting behavior in poly(aryl ether ketone ketone) containing alternated terephthalic and isophthalic moieties were studied by time-resolved synchrotron x-ray methods. Recently, this material has been shown to exhibit three polymorphs (forms I, II, and III). In this work, we further investigated their distinctive thermal properties and found that form I is the dominating and the most thermally stable phase while form II is favored by fast nucleation conditions and is the least stable phase. On the other hand, form III represents a minor intermediate phase that usually coexists with form I and can be transferred from form II and to form I. Structural and morphological changes in form I have been followed by simultaneous wide-angle x-ray diffraction (WAXD)/small-angle x-ray scattering (SAXS) measurements during cold- or melt-crystallization and subsequent melting. In all cases, a larger dimensional change was found in the crystallographic a-axis than the b-axis during heating and cooling. This may be due to the greater lateral stress variation with respect to temperature along the a direction of the primary lamellae which is induced by either the formation of secondary lamellae or the preferential chain-folding direction in poly(aryl ether ketone ketone)s. During the phase transitions of form II ← III in the cold-crystallized specimen and form III ← I in the melt-crystallized samples, lamellar variables (long period, lamellar thickness, and invariant) obtained from SAXS remain almost constant. This indicates that the density distribution in the long spacing is independent of the melting in form II or III. For melt-crystallization, the corresponding changes in unit-cell dimensions and lamellar morphology during the annealing-induced low endotherm are most consistent with the argument that these changes are due to the melting of thin lamellar population. © 1995 John Wiley & Sons, Inc.     

EPMA of interfaces applied to the solid oxide fuel cell

Chemical interactions at the phase boundaries of materials applied for the solid oxide fuel cell (SOFC) have been studied by EPMA. The chemical reactivity at the interface of La_y-xSr_xMnO₃/ZrO₂-Y₂O₃ is dependent on the stoichiometry (y) and the Sr content (x) of the perovskite. Typical reaction products (zirconates) and a diffusion zone in the ZrO₂–Y₂O₃ have been observed. The extension of cation release (Mn) is related to the increasing chemical activity of Mn oxide in the perovskite by the Sr substitution for La. The wettability of the metal/oxide interface in the anode cermet (Ni/ZrO₂–Y₂O₃) has been found to be influenced by chemical reactions resulting from the applied reducing atmosphere with high carbon activity. The disintegration of ZrO₂–Y₂O₃ in contact with molten Ni or Ni-Ti and Ni-Cr alloys leads to the redeposition of Y₂O₃-enriched oxides and also to Zr-rich intermetallic compounds and eutectics.     

Vibrational control of crystal growth from liquid phase

Modeling and numerical simulations of the convective flows induced by the vibration of the monocrystal during crystal growth have been performed for two configurations simulating the Cz and FZ methods. This permitted to emphasize the role of different vibrational mechanisms in the formation of the average flows. It is shown that an appropriate combination of these mechanisms can be used to counteract the usual convective flows (buoyancy- and/or thermocapillary-driven) inherent to crystal growth processes from the liquid phase. While vibrational convection is rather complex due to these identified mechanisms, the new modeling used in the present paper opens up very promising perspectives to efficiently control heat and mass transfer during real industrial applications of crystal growth from the liquid phase.     

Development of new dyes for use in integrated optical sensors

New chromoionophores have been developed, focused on NIR applications so that optode membranes may be used in monolithically integrated optical sensors. The wavelength of maximum absorbance has been estimated for a new model compound by the Pariser-Parr-Pople (PPP) method. Several cyanine type dyes have been tested as membrane chromoionophores. Membrane composition has been altered to overcome solubility problems. In this way, simple pH-sensitive optode membranes have been produced.     

Database reverse engineering: From requirements to CARE tools

This paper analyzes the requirements that CASE tools should meet for effective database reverse engineering (DBRE), and proposes a general architecture for data-centered applications reverse engineering CASE environments. First, the paper describes a generic DBMS-independent DBRE methodology, then it analyzes the main characteristics of DBRE activities in order to collect a set of desirable requirements. Finally, it describes DB-MAIN, an operational CASE tool developed according to these requirements. The main features of this tool that are described in this paper are its unique generic specification model, its repository, its transformation toolkit, its user interface, the text processors, the assistants, the methodological control and its functional extensibility. Finally, the paper describes five real-world projects in which the methodology and the CASE tool were applied. This is a heavily revised and extended version of “Requirements for Information System Reverse Engineering Support” by J.-L. Hainaut, V. Englebert, J. Henrard, J.-M. Hick, D. Roland, which first appeared in the Proceedings of the Second Working Conference on Reverse Engineering, IEEE Computer Society Press, pp. 136–145, July 1995. This paper presents some results of the DB-MAIN project. This project is partially supported by the Région Wallonne, the European Union, and by a consortium comprising ACEC-OSI (Be), ARIANE-II (Be), Banque UCL (Lux), BBL (Be), Centre de recherche public H. Tudor (Lux), CGER (Be), Cockerill-Sambre (Be), CONCIS (Fr), D'Ieteren (Be), DIGITAL, EDF (Fr), EPFL (CH), Groupe S (Be), IBM, OBLOG Software (Port), ORIGIN (Be), Ville de Namur (Be), Winterthur (Be), 3 Suisses (Be). The DB-Process subproject is supported by the Communauté Fran?aise de Belgique.     

Toughening of epoxies via craze-like damage

The fracture behavior of a core-shell rubber (CSR) modified epoxy is investigated using both fracture mechanics and microscopy tools. The CSR-modified epoxy is found to be toughened via numerous line-array cavitations of the CSR particles, followed by plastic flow of the epoxy matrix. The toughening effect via the above craze-like damage process is found to be as effective as that of the well-known widespread rubber cavitation/matrix shear yielding mechanisms. The conditions for triggering the craze-like damage appear to be both stress state and rubber concentration dependent. The type of rubber tougheners utilized also plays a critical role in triggering this rather unusual craze-like damage in epoxy systems. © 1993 John Wiley & Sons, Inc.