Langduin C, a novel dimeric diterpenoid from the roots of Euphorbia fischeriana

Langduin C, a novel dimeric diterpenoid, was isolated from the roots of Euphorbia fischeriana and its structure was established by spectral data and single-crystal X-ray diffraction analysis.     

WEIGHTED APPROXIMATION ON SZASZ—TYPE OPERATORS

In this paper, we use weighted modules ω(?)(f,t)w to study the pointwise approximation on Szasz-type operators, and obtain the direct and converse theorem, as well as characterizations of the pointwise approximation of Jacobi-weighted Szasz-type operators.     

R~(n+1)中常高阶平均曲率超曲面

本文给出了Rn+1中超曲面的一些积分公式,并利用这些积分公式得到了以球面为边界的常高阶平均曲率超曲面的一些唯一性结果.     

Low Cost, High Efficiency, Gain Flattened L Band EDFA Using FBGs as C Band Seed Generators

A low cost, coolerless 980nm diode pumped, gain flattened L band EDFA with fast transient control, high pump efficiency and gain clamping effect was realized by using FBGs as C band seed generators.     

磁电垒结构中自旋极化输运性质的研究

研究了电子隧穿几类磁电垒结构的自旋极化输运性质，导出统一的传输概率公式，揭示了非 均匀磁场的分布与自旋过滤的关系，同时表明采用有效朗德因子较大的半导体材料可以显著 增强磁电垒结构的自旋过滤效果. 关键词： 磁电垒 自旋过滤 自旋电子学 自旋极化     

CNx纳米管的制备、结构观察及低场致电子发射性能研究

采用高温热解法，以乙二胺为前驱液，在沉积有铁催化剂的p型硅（111）基底上制备出了定向生长的CNx纳米管.利用扫描电子显微镜、高分辨率透射电子显微镜和拉曼光谱对CNx纳米管进行了形貌观察和表征.CNx纳米管的高度在20?μm左右，直径在50—100nm之间，具有明显的“竹节状”结构，结晶有序度较差.对CNx纳米管薄膜进行低场致发射性能测试：外加电场为1.4V/μm，观察到20?μA /cm2发射电流，外电场升至2.54V/μm时发射电流达到1.280mA/cm2，在较高外电场下，没有发现电流“饱和”.这比 关键词： CNx纳米管 高温热解 “竹节状”结构 场致发射     

Fast Si magic-angle-spinning NMR acquisitions by RAPT-CP Al → Si polarization transfer

Using enhancement of the ²⁷Al central-transition magnetization by applying RAPT prior to ²⁷Al → ²⁹Si cross-polarization, we demonstrate fast acquisition of ²⁹Si one-dimensional MAS and two-dimensional ²⁷Al–²⁹Si HETCOR spectra on a new sialon phase Ba₂Al₃Si₉N₁₃O₅.     

Status of heavy element research using a gas-filled recoil separator at RIKEN

A gas-filled type of recoil separator for heavy element research was installed at an experimental hall of RIKEN Linear Accelerator facility to realize getting higher intensity of primary beam and long beam time. Performance of the separator was studied using target recoils and various nuclear reactions. The results show the high performance of the separator for heave element research. As an application of the GARIS, production and identification of an isotope of the 110th element ²⁷¹[110] have been performed using the ²⁰⁸Pb(⁶⁴Ni,1n)²⁷¹[110] reaction. Three decay chains coincide well both in decay times and energies with the ones reported by the group of SHIP experiment at GSI, Germany. Our results provide a confirmation of the synthesis of an isotope ²⁷¹[110] of element 110.     

Proteins Entrapped in Silica Monoliths Prepared from Glyceroxysilanes

The preparation of discrete polyol based silane precursors derived from glycerol by a simple one-pot process is described. These polyol-based silanes could be hydrolyzed under mild pH conditions and upon gelation resulted in the formation of optically clear, monolithic, mesoporous silica. The hydrolysis and condensation reactions lead to cure rates that are very sensitive to ionic strength, but are almost unaffected by pH in contrast to those of alkoxysilanes derived from primary alcohols such as Si(OEt)₄. Residual glycerol in the silica monolith could be removed by washing, or could be left in the silica to reduce the magnitude of shrinkage during long term storage. The biocompatible glyceroxysilane precursors lead to materials that were able to retain the activity of entrapped enzymes over repeated cycles of use for periods of up to several months.     

Exploitation of introducing of catalytic centers into layer galleries of layered silicates and related epoxy nanocomposites. I. Epoxy nanocomposites derived from montmorillonite modified with catalytic surfactant‐bearing carboxyl groups

Montmorillonite (MMT) was modified with the acidified cocamidopropyl betaine (CAB) and the resulting organo‐montmorillonite (O‐MMT) was dispersed in an epoxy/methyl tetrahydrophthalic anhydride system to form epoxy nanocomposites. The intercalation and exfoliation behavior of the epoxy nanocomposites were examined by X‐ray diffraction and transmission electron microscopy. The curing behavior and thermal property were investigated by in situ Fourier transform infrared spectroscopy and DSC, respectively. The results showed that MMT could be highly intercalated by acidified CAB, and O‐MMT could be easily dispersed in epoxy resin to form intercalated/exfoliated epoxy nanocomposites. When the O‐MMT loading was lower than 8 phr (relative to 100 phr resin), exfoliated nanocomposites were achieved. The glass‐transition temperatures (T_g's) of the exfoliated nanocomposite were 20 °C higher than that of the neat resin. At higher O‐MMT loading, partial exfoliation was achieved, and those samples possessed moderately higher T_g's as compared with the neat resin. O‐MMT showed an obviously catalytic nature toward the curing of epoxy resin. The curing rate of the epoxy compound increased with O‐MMT loading. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1192–1198, 2004