MODIS通道1和通道2大气订正的一种快速实用方法

提出了利用气象资料对MODIS影像进行大气校正的一种快速实用方法.读取MODIS前两个通道250min的反射率,采用常用的黑色目标扣除法(Dark-object subtraction)计算天空程辐射,通过卫星过境时刻的气象能见度和水汽资料计算大气透过率,最后推导出目标物的反射率.通过比较两个邻近日期MODIS影像校正前后的归一化植被指数(NDVI)值,得出利用本文提出的方法对MODIS进行大气校正所得到的NDVI值更接近实际情况.结果表明:利用气象能见度和水汽压可以对MODIS数据进行快速有效的大气校正.     

Interior point cutting plane method for optimal power flow

In this paper, an interior point cutting plane method (IPCPM)is applied to solve optimal power flow (OPF) problems. Comparedwith the simplex cutting plane method (SCPM), the IPCPM is simpler,and efficient because of its polynomial-time characteristic.Issues in implementing IPCPM for OPF problems are addressed,including (1) how to generate cutting planes without using thesimplex tableau, (2) how to identify the basis variables inIPCPM, and (3) how to generate mixed integer cutting planes.The calculation speed of the proposed algorithm is further enhancedby utilizing the sparsity features of the OPF formulation. Numericalsimulations on IEEE 14-300-bus test systems have shown thatthe proposed method is effective.     

p型导电掺In的SnO_2薄膜的制备及表征

采用溶胶 凝胶提拉法成功地制备了p型导电掺In的SnO2 薄膜 .x射线衍射测试结果表明 ,掺In的SnO2 薄膜保持SnO2 的金红石结构 .吸收谱测试结果表明 ,掺In的SnO2 禁带宽度为 3 8eV .霍尔测量结果表明 ,空穴浓度与热处理温度有很大的关系 ,5 2 5℃为最佳热处理的温度 .铟锡原子比在 0 0 5— 0 2 0范围内 ,空穴的浓度与In的含量有直接的关系 ,并随In含量的增加而增加     

Rugged distal tips for CO2 laser medicine

Low-loss and rugged distal tips for CO₂ laser have been proposed and fabricated based on a commercially available stainless steel (St) pipe. A method of smoothening the inner surface of the St pipe with a rough inner surface is put forward. Fabrication parameters, transmission properties, and mechanical strength of the cyclic olefin polymer-coated silver hollow St distal tip are experimentally discussed.     

利用模式的对称性研究光子晶体光纤的色散

由光子晶体光纤的对称性可以得到模式分布的对称性，根据模式的对称性选择适当的展开函数，可以使计算量大大减少。计算了六角结构光子晶体光纤的色散特性，得到了波长在1．55pm处色散为零时，光子晶体光纤的结构参量所满足的方程。     

某轴流压气机叶尖间隙效应实验研究

本文对某低速轴流压气机叶尖间隙尺度对性能的影响进行了实验研究,并通过不同的机匣结构情况研究一种叶尖漏流不敏感机匣。实验表明,不同的间隙尺度对叶轮机总体性能存在十分明显的影响。对绝大部分运行状态,小间隙下的压升和效率均明显高于大间隙的情况。另外,所采用的毛刷式和篦齿式的机匣实验结果表明,不论毛刷式还是篦齿式机匣,在大流量负攻角情况下对性能的影响不大,但毛刷式机匣并不能达到提高失速裕度的目的,而篦齿式机匣在小流量情况下对压升有所提高,但对效率影响不大。     

Phase formation and control of morphology in sputtered Cu-In alloy layers

The dependence of structural properties and surface morphology of Cu-In alloy layers on the composition and sputtering deposition sequence were investigated by X-ray diffraction, scanning electron microscopy and energy-dispersive X-ray spectroscopy. The properties of the co-sputtered alloy layers changed abruptly around the composition boundary when the Cu/In ratio reached 1/2. This can be explained by the effective heat of formation (EHF) model, which has been used to predict the sequence of phase formation for metal diffusion couples. The use of a co-sputtered alloy layer with a high In concentration was not suitable for fabricating solar cells, because the film had a very rough morphology due to large In islands formed on the CuIn₂ phase. However, it was possible to minimize this phase by In sputtering followed by co-sputtering with a Cu/In ratio of 1 (Cu-In/In/Glass). This permitted the fabrication of a homogeneous Cu-In alloy layer, which was not possible through the simple co-sputtering.     

双预脉冲驱动X射线激光实验研究

 在“星光-Ⅱ”激光装置上进行了双预脉冲驱动类氖铬X射线激光实验，介绍了实验方法和实验结果，并对结果进行了简短讨论。由于目前“星光”装置输出能量较低，所进行的双预脉冲驱动未能显著提高X射线激光强度，改变预脉冲幅度时X射线激光强度也未有显著变化。利用MED103程序进行了模拟计算，其结果与实验结果一致。     

Bi12TiO20纳米粉体的制备及其光吸收特性研究

以钛酸四丁酯和硝酸铋为原料 ,利用化学溶液分解法制备了Bi12 TiO2 0 纳米多晶粉体 .采用XRD和TEM对其结构和形貌进行了表征 .结合热重 差热 (TG DTA)分析 ,探讨了Bi12 TiO2 0 晶相的形成机理 .通过UV Vis漫反射谱的测定 ,研究了Bi12 TiO2 0 纳米晶粉体的光吸收特性 .结果显示 ,从组成为化学计量比的前驱液中可以很容易制得纯Bi12 TiO2 0 纳米晶粉体 ,该Bi12 TiO2 0 纳米晶粉体呈现了在很宽的波长范围内 (5 6 0～ 385nm )对光的吸收的特性 .     

改革物理实验课教学,提高实验课的教学质量

根据多年的物理实验教学经验，阐明了物理实验教学改革应重视的问题，并提出了几点改进措施。