Solubility of methane in octane + ethanol at temperatures from 303.15 K to 333.15 K and pressures up to 12.01 MPa

Solubility of methane in octane + ethanol was measured at temperatures ranging from 303.15 K to 333.15 K and pressures ranging from 2.60 MPa to 12.01 MPa. Experimental data were analyzed using the Soave-Redlich-Kwong equation of state with three types of mixing rules, and the estimated average deviation from the experimental solubility data was less than 3.5 %.     

Design of polyglycidol-containing microspheres for biomedical applications

The paper presents a short review on the synthesis, characterisation and selected medical applications of poly(styrene/α-tert-butoxy-ω-vinylbenzyl-polyglycidol) (P(S/PGL)) microspheres. The soap-free emulsion-polymerisation of styrene and α-tert-butoxy-ω-vinylbenzyl-polyglycidol macromonomer (PGL) in water yielded core-shell microspheres with a low particle-diameter dispersity (ratio of the weight average particle diameter and the number average particle diameter). The interfacial fraction of PGL units, estimated by XPS, was in the range of 0–42 mole % depending on the concentration of the macromonomer in the polymerisation feed. The studies of adsorption of model proteins showed that the surface fraction of adsorbed protein was significantly reduced when the PGL interfacial fraction was higher than 40 mole %. The P(S/PGL) particles with covalently immobilised proteins were used for the preparation of photonic crystal assemblies suitable for applications in optical biosensors and the medical diagnostic test for the detection of Helicobacter pylori antibodies in the blood serum.     

Synthesis and properties of new biotin compounds containing hexyltriethylene glycol chain

The synthesis of a new halogenide containing hexyltriethylene glycol chain functionalized with biotin is reported. The general possibility of this linker to use as the building block for biotinylated compounds syntheses is demonstrated. Two biotinylated esters with different properties for useful surface modification and as fluorescence probes for proteins marking were synthesized. The properties of mentioned compounds were investigated by using surface plazmon resonance ellypsometry and fluorescence spectroscopy.     

Soret and Dufour Effects on Double-Diffusive Free Convection Over a Vertical Truncated Cone in Porous Media with Variable Wall Heat and Mass Fluxes

This work studies the Soret and Dufour effects on the double-diffusive free convection over a downward-pointing vertical truncated cone with variable wall heat and mass fluxes in fluid-saturated porous media. A coordinate transformation is used to derive the nondimensional boundary-layer governing equations, and the obtained nonsimilar equations are then solved by the cubic spline collocation method. Results for local surface temperature and the local surface concentration are presented as functions of Soret parameters, Dufour parameters, power-law exponents, buoyancy ratios, and Lewis numbers. Results show that increasing the Dufour parameter tends to increase the local surface temperature, while it tends to decrease the local surface concentration. An increase in the Soret number leads to a decrease in the local surface temperature for buoyancy assisting flows, while it leads to an increase in the local surface temperature for buoyancy opposing flows. Increasing the Soret number tends to increase the local surface concentration. Moreover, the local surface temperature and the local surface concentration of the truncated cones with higher power-law exponents are lower than those with lower exponents.     

Study of Heat Transport in Bénard-Darcy Convection with g-Jitter and Thermo-Mechanical Anisotropy in Variable Viscosity Liquids

The effects of temperature-dependent viscosity, gravity modulation and thermo-mechanical anisotropies on heat transport in a low-porosity medium are studied using the Ginzburg–Landau model. The effect of gravity modulation is to decrease the Nusselt number, Nu and variable viscosity leads to increase in Nu. The thermo-mechanical anisotropies have opposite effect on Nu with thermal anisotropy decreasing the heat transport.     

A Note on the Legendre Series Solution of the Biharmonic Equation for Cylindrical Problems

The solution of cylindrical problems is addressed. A series solution is considered of the biharmonic equation, in which the series terms of the stress function Φ are expressions based upon Legendre polynomials and logarithmically singular functions. An explicit form of a polynomial supplementing each logarithmically singular part of the series solution is obtained.     

An Incompressible Fluid in a Weakly Deformable Shell. Part I: Analysis of the Model

We consider the flow of a viscous incompressible fluid in a pipe when the boundary is a deformable shell of Naghdi type. We prove that the corresponding system of partial differential equations has a solution when the deformation of the shell is smooth and small enough. We propose an algorithm that uncouples the unknowns and prove its convergence.     

Nonlinear analysis of laser droplet generation by means of 0–1 test for chaos

We apply the recently improved version of the 0–1 test for chaos to real experimental time series of laser droplet generation process. In particular two marginal regimes of dripping are considered: spontaneous and forced dripping. The outcomes of the test reveal that both spontaneous and forced dripping time series can be characterized as chaotic, which coincides with the previous analysis based on nonlinear time series analysis.     

Scheduling Parts in a Combined Production-transportation Work Cell

This paper is concerned with a combined production-transportation scheduling problem. The problem comprises a simple, two-machine, automated manufacturing cell, which either stands alone or is a subunit of a complete flexible manufacturing system. The cell consists of two machines in series with a dedicated part-handling device such as a crane or robotic arm for transferring parts from the first machine to the second. The loading of a new piece on the first machine and the ejection of a finished piece from the second machine are performed by dedicated automated mechanisms. The introduction of parts into the system is done n at a time, whereby the parts are reshuffled into a sequence that minimizes completion time. All processing and transfer times are considered deterministic—a reasonable assumption for a cell comprising a robotic transfer device and two CNC machining units. What complicates the problem is the assumption of a non-negligible time for the transfer device to return (empty) from the second machine to the first. The operation is a generalization of a two-machine flowshop problem, and is formulated as a specially structured, asymmetric travelling salesman problem. An approximate polynomial time 0(n log n) algorithm is proffered. The procedure incorporates a lower bound using the Gilmore–Gomory algorithm for the no-wait, two-machine flowshop problem.