The Morphology of Liquid-Crystalline Polymers and the Possible Consequences for their Rheological Behaviour

Abstract

Polymer liquid crystals can occur as polydomain materials where the domain size may be tens of microns. While the material within each domain may be characterized by a common order parameter, the directors of the domains can be more or less randomly distributed. Since the transition from polydomain to monodomain material only involves the removal of grain boundaries and the alignment of directors, the free energy change must necessarily be small. Such a transition can readily be achieved, therefore, by the action of any external field: electrical, magnetic, stress or surface. In this work optical photomicrographs of polymeric liquid crystals with widely varying and in some cases well controlled morphologies are presented. Probable dependence of rheological behaviour on morphology is also discussed. Such dependence is expected to be considerable under certain conditions. Due to experimental and sample limitations, however, direct correlations of rheology and morphology are sparse. Morphological consequences for the rheology of liquid-crystalline materials can be exemplified by the following possibilities. In contrast to the case of isotropic melts, wall effects can be non-negligible. Zero shear rate rheological parameters are not expected to be uniquely defined quantities since the domain sizes are large and the director may not be effectively averaged over typical sample dimensions. Non-zero shear-rate measurements of rheological parameters is effected by the propensity of: (1) individual domain directors to align under the influence of a stress field and (2) flow alignment to dominate surface-induced alignment above some critical shear rate. The effects might be manifested by a non-newtonian regime as well as yield stress behaviour and thixotropy. The kinetics of relaxation from mono- to poly-domain material has implications for the dynamic response and rheological hysterises of the material.     

An Aldehyde Responsive,Cleavable Linker for Glucose Responsive Insulins

A glucose responsive insulin (GRI) that responds to changes in blood glucose concentrations has remained an elusive goal. Here we describe the development of glucose cleavable linkers based on hydrazone and thiazolidine structures. We developed linkers with low levels of spontaneous hydrolysis but increased level of hydrolysis with rising concentrations of glucose, which demonstrated their glucose responsiveness in vitro. Lipidated hydrazones and thiazolidines were conjugated to the LysB29 side-chain of HI by pH-controlled acylations providing GRIs with glucose responsiveness confirmed in vitro for thiazolidines. Clamp studies showed increased glucose infusion at hyperglycemic conditions for one GRI indicative of a true glucose response. The glucose responsive cleavable linker in these GRIs allow changes in glucose levels to drive the release of active insulin from a circulating depot. We have demonstrated an unprecedented, chemically responsive linker concept for biopharmaceuticals.     

A Practical Procedure for the Solid-Phase Synthesis of Racemic 2,2′-Dihydroxy-1,1′-binaphthyl

Abstract: A high yielding solid-phase dimerisation of 2-naphthol by means of a ball-milling procedure is described.

     

Lipases,liposomes and lipid-prodrugs

Colloidal and interfacial phenomena lie at the core of drug formulation, drug delivery, as well as drug binding and action at diseased sites, e.g., in cancer therapy. We review a class of liposome-based drug-delivery systems whose design and functional properties are intimately controlled by the stability of sub-micron structures, lipid-bilayer interfaces, and interfacially activated enzymes that can be exploited to target and deliver drugs. Moreover these drugs can themselves be special lipid molecules in the form of lipid prodrugs that both form the liposomal carrier as well as the substrate for endogenously upregulated lipases that turn the prodrugs into potent drugs precisely at the diseased site.     

SPE HG-AAS method for the determination of inorganic arsenic in rice—results from method validation studies and a survey on rice products

The present paper describes the development, validation and application of a method for inorganic arsenic (iAs) determination in rice samples. The separation of iAs from organoarsenic compounds was done by off-line solid-phase extraction (SPE) followed by hydride generation atomic absorption spectrometry (HG-AAS) detection. This approach was earlier developed for seafood samples (Rasmussen et al., Anal Bioanal Chem 403:2825–2834, 2012) and has in the present work been tailored for rice products and further optimised for a higher sample throughput and a lower detection limit. Water bath heating (90 °C, 60 min) of samples with dilute HNO₃ and H₂O₂ solubilised and oxidised all iAs to arsenate (As^V). Loading of buffered sample extracts (pH 6?±?1) followed by selective elution of arsenate from a strong anion exchange SPE cartridge enabled the selective iAs quantification by HG-AAS, measuring total arsenic (As) in the SPE eluate. The in-house validation gave mean recoveries of 101–106 % for spiked rice samples and in two reference samples. The limit of detection was 0.02 mg kg^?1, and repeatability and intra-laboratory reproducibility were less than 6 and 9 %, respectively. The SPE HG-AAS method produced similar results compared to parallel high-performance liquid chromatography coupled to inductively coupled plasma mass spectrometry (ICP-MS) analysis. The SPE separation step was tested collaboratively, where the laboratories (N?=?10) used either HG-AAS or ICP-MS for iAs determination in a wholemeal rice powder. The trial gave satisfactory results (HorRat value of 1.6) and did not reveal significant difference (t test, p?>?0.05) between HG-AAS and ICP-MS quantification. The iAs concentration in 36 rice samples purchased on the Danish retail market varied (0.03–0.60 mg kg^?1), with the highest concentration found in a red rice sample.      

Quantification of 31 illicit and medicinal drugs and metabolites in whole blood by fully automated solid-phase extraction and ultra-performance liquid chromatography–tandem mass spectrometry

An efficient method for analyzing illegal and medicinal drugs in whole blood using fully automated sample preparation and short ultra-high-performance liquid chromatography–tandem mass spectrometry (MS/MS) run time is presented. A selection of 31 drugs, including amphetamines, cocaine, opioids, and benzodiazepines, was used. In order to increase the efficiency of routine analysis, a robotic system based on automated liquid handling and capable of handling all unit operation for sample preparation was built on a Freedom Evo 200 platform with several add-ons from Tecan and third-party vendors. Solid-phase extraction was performed using Strata X-C plates. Extraction time for 96 samples was less than 3 h. Chromatography was performed using an ACQUITY UPLC system (Waters Corporation, Milford, USA). Analytes were separated on a 100 mm?×?2.1 mm, 1.7 μm Acquity UPLC CSH C₁₈ column using a 6.5 min 0.1 % ammonia (25 %) in water/0.1 % ammonia (25 %) in methanol gradient and quantified by MS/MS (Waters Quattro Premier XE) in multiple-reaction monitoring mode. Full validation, including linearity, precision and trueness, matrix effect, ion suppression/enhancement of co-eluting analytes, recovery, and specificity, was performed. The method was employed successfully in the laboratory and used for routine analysis of forensic material. In combination with tetrahydrocannabinol analysis, the method covered 96 % of cases involving driving under the influence of drugs. The manual labor involved in preparing blood samples, solvents, etc., was reduced to a half an hour per batch. The automated sample preparation setup also minimized human exposure to hazardous materials, provided highly improved ergonomics, and eliminated manual pipetting.

Novel Tripod Amphiphiles for Membrane Protein Analysis

Integral membrane proteins play central roles in controlling the flow of information and molecules across membranes. Our understanding of membrane protein structures and functions, however, is seriously limited, mainly due to difficulties in handling and analysing these proteins in aqueous solution. The use of a detergent or other amphipathic agents is required to overcome the intrinsic incompatibility between the large lipophilic surfaces displayed by the membrane proteins in their native forms and the polar solvent molecules. Here, we introduce new tripod amphiphiles displaying favourable behaviours toward several membrane protein systems, leading to an enhanced protein solubilisation and stabilisation compared to both conventional detergents and previously described tripod amphiphiles.     

Formation and Structure of Fluorescent Silver Nanoclusters at Interfacial Binding Sites Facilitating Oligomerization of DNA Hairpins

Fluorescent, DNA‐stabilized silver nanoclusters (DNA‐AgNCs) are applied in a range of applications within nanoscience and nanotechnology. However, their diverse optical properties, mechanism of formation, and aspects of their composition remain unexplored, making the rational design of nanocluster probes challenging. Herein, a synthetic procedure is described for obtaining a high yield of emissive DNA‐AgNCs with a C‐loop hairpin DNA sequence, with subsequent purification by size‐exclusion chromatography (SEC). Through a combination of optical spectroscopy, gel electrophoresis, inductively coupled plasma mass spectrometry (ICP‐MS), and small‐angle X‐ray scattering (SAXS) in conjunction with the systematic study of various DNA sequences, the low‐resolution structure and mechanism of the formation of AgNCs were investigated. Data indicate that fluorescent DNA‐AgNCs self‐assemble by a head‐to‐head binding of two DNA hairpins, bridged by a silver nanocluster, resulting in the modelling of a dimeric structure harboring an Ag₁₂ cluster.     

Concentrations of rare earth elements in sediments,mussels and fish from a Danish marine environment,Lillebaelt

Results for the content of the rare earth elements (REE), La, Ce, Nd, Sm, Eu, Tb, Yb and Lu in sediments, mussels and fish are presented for an area polluted by REE. The REE are emitted with the process waste water stream from a fertilizer production plant. The method of analysis has been INAA. An attempt to combine the INAA with a simple destruction/preconcentration method is described.