A Bifunctional B,N-Based Asymmetric Catalytic Nitrostyrene-Michael Addition Acting through a 10-Membered Ring Cyclic Transition State

The B,N-bifunctional catalyst homoboroproline has been applied to a catalytic asymmetric nitroalkene-Michael addition to β-nitrostyrene analogues, showing broad substrate tolerance, high conversions and moderate to good asymmetric induction. The ability of homoboroproline to act as an efficient catalyst based on enamine-formation of the secondary amine, coupled with intramolecular Lewis-acid chelation of the nitro function, in a non-FLP manner, to effect efficient and enantioselective catalysis via a proposed large 10-membered ring transition state is remarkable and reinforced by theoretical calculations.     

Single Chlamydomonas reinhardtii cell separation from bacterial cells and auto-fluorescence tracking with a nanosieve device

A planar, transparent, and adaptable nanosieve device is developed for efficient microalgae/bacteria separation. In the proposed method, a sacrificial layer is applied with dual photolithography patterning to achieve a 1D channel with a very low aspect ratio (1:10 000). A microalgae/bacteria mixture is then introduced into the deformable PDMS nanochannel. The hydrodynamic deformation of the nanochannel is regulated to allow the bacteria cells to pass through while leaving the microalgae cells trapped in the device. At a flow rate of 4 μL/min, the supernatant collected from the device is indistinguishable from a control solution, indicating that nearly all the microalgae cells are trapped in the device. Additionally, this device is capable of single cell auto-fluorescence tracking. These microalgae cells demonstrate minimal photobleaching over 250 s laser exposure and could be used to monitor hazardous compounds in the sample with a continuous flow. This method will be valuable to purify microalgae samples containing contaminations and study single-cell heterogeneity.     

肿瘤乏氧靶向响应的罗丹明荧光探针及其成像介导手术治疗

基于罗丹明的良好荧光性能, 经化学偶联反应制备并表征了一个偶氮乏氧特异响应的“Off-On”型荧光成像探针(FY-4). 从分子层面证实了其荧光“Off-On”性能和响应机制; 在L02正常细胞及4T1, HeLa和A549肿瘤细胞层面考察了其对受试细胞株的毒性和不同乏氧时间的荧光成像性能; 再利用4T1肿瘤模型, 分别以肿瘤原位注射和尾静脉注射的方式考察了其荧光成像性能, 并探究了其荧光成像介导切除肿瘤性能, 最后还考察了FY-4的生物安全性. 结果表明, FY-4有高的肿瘤乏氧靶向特异“关-开”响应的荧光成像差异显影及荧光成像介导切除肿瘤的潜能, 结合其良好的光物理性能、 生物安全性和明晰的给药时间等特性, 有望为生物医学荧光成像介导肿瘤切除提供新的研究工具.     

基于乙炔基-苯并噁嗪单元双重交联反应的聚酰亚胺树脂的制备与性能

为开发可低温固化的聚酰亚胺树脂, 通过分子结构设计将苯并噁嗪单元引入聚酰亚胺树脂中, 合成了含苯并噁嗪单元及乙炔基封端的双官能化新型聚酰亚胺预聚体(PIBzA). 经高温处理, 苯并噁嗪单元发生开环交联, 同时, 乙炔基端基发生三聚成环反应, 从而在固化树脂中形成双重交联网络结构. 苯并噁嗪单元的引入使聚酰亚胺树脂最快固化反应温度降低约32 ℃, 有效降低了固化温度. 同时, 苯并噁嗪单元的引入未大幅度降低树脂的耐热稳定性, 其玻璃化转变温度(T_g)介于266~290 ℃之间, 5%热失重温度(T_d,5%)接近500 ℃, 依然可以满足耐高温复合材料的应用需求. 此外, PIBzA固化树脂具有低介电特性, 其介电常数k介于2.3~3.0, 介电损耗介于0.002~0.008, 可满足透波复合材料及先进微电子封装材料的应用需求.     

ABC三嵌段共聚物胶束从多间隔结构到多核结构转变的Monte Carlo模拟

采用Monte Carlo模拟方法研究了疏水-亲水-疏水(H-P-H)型ABC三嵌段共聚物在B嵌段的选择性溶剂中的自组装行为. 模拟结果表明, 通过调节A嵌段和C嵌段的疏水性和二者之间的不相容性, 体系中可以形成多种形貌各异的胶束. 根据胶束中疏水核结构的特点, 这些胶束大体上可以被分为多核型胶束和多间隔型胶束两种类型. 通过增强疏水嵌段的疏水性或降低A嵌段和C嵌段间的不相容性, H-P-H型ABC三嵌段共聚物胶束能够发生从多核型胶束向多间隔型胶束的转变. 进一步分析胶束中聚合物的链构象等微观结构信息发现, A嵌段和C嵌段间的排斥作用和疏水作用之间存在竞争关系, 而这种竞争关系是影响体系中形成多核型胶束还是多间隔型胶束的决定性因素.     

固体核磁共振Multiple-CP定量技术的参数优化与应用研究

固体核磁共振Multiple-CP定量技术可实现对不同体系、 不同定量信息的检测. 然而, Multiple-CP对样品属性的宽容度较低, 其中有关样品属性的核磁共振参数包括氢的自旋晶格弛豫时间(T_1,H)、 交叉弛豫时 间(T_CH)和自旋锁定场下氢的自旋晶格弛豫时间(T_{\mathrm{1}\rho }^{\text{?}\mathrm{H}})等. 因而需要系统地掌握Multiple-CP各种实验参数与样品上述特性参数之间的关系, 从而确定Multiple-CP技术可适用的体系范围以及最优的实验参数范围. 基于此, 首先以L-丙氨酸为模型样品, 探讨在Multiple-CP实验中弛豫恢复时间(t_d)、 交叉极化接触时间(t_p)和交叉极化次数(n) 3种实验参数对分子中基团比例测量结果的影响规律. 并以L-缬氨酸、 L-丙氨酸/L-缬氨酸的混合物为模型样品, 探讨样品特性参数的差异性对Multiple-CP实验参数范围的影响. 实验结果表明, t_p受T_CH和\text{?}{T}_{\mathrm{1}\rho }^{\text{?}\mathrm{H}}的影响较大. 对于纯净物或均相体系, T_CH是影响t_p参数设置的关键. 依据实验数据发现, 当样品中各基团T_CH差异度小于8%时, 实验对t_p的宽容度较高; 对于混合物体系, 需同时考虑混合物中组分\text{?}{T}_{\mathrm{1}\rho }^{\text{?}\mathrm{H}\text{?}}差异度的影响. 当组分\text{?}{T}_{\mathrm{1}\rho }^{\text{?}\mathrm{H}\text{?}}差异度为32%、 各基团T_CH差异度为21%时, Multiple-CP对t_p的宽容度高, 可在较宽的参数范围内实现定量检测. 而当T_CH差异度较大时, 获取定量结果时t_p的参数范围较小, 实验条件较苛刻. Multiple-CP定量方法更适用于T_CH和\text{?}{T}_{\mathrm{1}\rho }^{\text{?}\mathrm{H}\text{?}}差异度较小的样品体系的定量研究. 通过研究样品T_CH和\text{?}{T}_{\mathrm{1}\rho }^{\text{?}\mathrm{H}\text{?}}对实验参数的影响, 总结了Multiple-CP方法所适用的样品体系特征, 为使用Multiple-CP进行定量检测提供可参考的参数设置方案.     

Preparation of Low-dielectric Permittivity Polyimide Resins with High Surface Activity from Chemically Bonded Hyperbranched Polysiloxane

Thermosetting resin matrix is the key component of advanced wave-transparent composites,where low dielectric constant,excellent processability,high thermal stability,as well as good bonding ability are required for resins.Herein,we prepared a series of phenylethynyl terminated polyimide(PI)resins by grafting amine-functionalized hyperbranched polysiloxane(HBPSi)to PI chains during the in situ polymerization.The effects of HBPSi on the processability of oligomers,molecular packing,thermal stability,dielectric property and bonding ability to reinforce Kevlar fibers of the cured PI/HBPSi composite resins have been examined in detail.The dielectric constants of the cured composite resins were greatly reduced from 3.29 to 2.19 without compromising its processability and thermal stability.Meanwhile,the 10 wt％HBPSi-containing PI resin demonstrated better bonding ability to reinforce fibers with the interfacial shear strength(IFSS)of 37.64 MPa,compared with that of neat PI-6 matrix(27.34 MPa),and better adhesion to metal with the lap shear strength of 10.48 MPa,50％higher than that of neat resin PI-6(6.98 MPa).These resultant PI/HBPSi composite resins exhibit excellent comprehensive properties,indicating their great potential as low-dielectric constant resin matrix in radar radome.     

Synergic Enhancement of High-density Polyethylene through Ultrahigh Molecular Weight Polyethylene and Multi-flow Vibration Injection Molding: A Facile Fabrication with Potential Industrial Prospects

General-purpose plastics with high strength and toughness have been in great demand for structural engineering applications. To achieve the reinforcement and broaden the application scope of high-density polyethylene(HDPE), multi-flow vibration injection molding(MFVIM) and ultrahigh molecular weight polyethylene(UHMWPE) are synergistically employed in this work. Herein, the MFVIM has better shear layer control ability and higher fabrication advantage for complex parts than other analogous novel injection molding technologies reported.The reinforcing effect of various filling times and UHMWPE contents as well as the corresponding microstructure evolution are investigated.When 5 wt% UHMWPE is added, MFVIM process with six flow times thickens the shear layer to the whole thickness. The tensile strength and modulus increase to 2.14 and 1.39 times, respectively, compared to neat HDPE on the premise of remaining 70% impact strength. Structural characterizations indicate that the enhancement is attributed to the improvement of shish-kebab content and lamellae compactness, as well as related to the corresponding size distributions of undissolved UHMWPE particles. This novel injection molding technology with great industrial prospects provides a facile and effective strategy to broaden the engineering applications of HDPE materials. Besides, excessive UHMWPE may impair the synergistic enhancement effect, which is also reasonably explained.     

High-strength and low-swelling chitosan/cellulose microspheres as a high-efficiency adsorbent for dye removal

Cellulose - Dye contamination of water supplies has a serious threat to human health, prompting the development of highly effective and eco-friendly adsorbents. In this work, polyelectrolyte...     

KIT-6负载CeO2催化CO2和甲醇合成碳酸二甲酯

采用不同老化温度(80、100、120和150℃)合成了一系列KIT-6载体,并通过浸渍法制备了相应的CeO_2/KIT-6催化剂。结合X射线衍射、N_2物理吸附、NH_3程序升温脱附、CO_2程序升温脱附、透射电子显微镜、傅里叶变换红外光谱和X射线光电子能谱等表征结果,详细考察了老化温度对KIT-6结构以及CeO_2/KIT-6催化剂直接催化CO_2和甲醇合成碳酸二甲酯(DMC)反应活性的影响。结果表明,不同老化温度下制备的KIT-6均保持其独特的三维孔道结构。随着老化温度升高,KIT-6比表面积先增大后减小,当老化温度为100℃时,KIT-6比表面积达到最大(683 m~2·g~(-1))。KIT-6较高的比表面积有利于提高CeO_2分散度,进而提高暴露的活性位点数量,催化活性随催化剂表面中等碱/酸性吸附位数量和Ce~(3+)含量的增加而逐渐提高。其中,CeO_2/100-KIT-6催化剂中CeO_2颗粒尺寸最小(5.9 nm),暴露的活性位数量最高,催化活性最佳。随后,考察了反应温度和压力对CeO_2/100-KIT-6催化活性的影响。随着反应温度提高,催化活性先升高后降低,当反应温度为140℃时,催化活性最高;且催化活性随反应压力的提高而逐渐增加。在反应温度为140℃、压力为6.8 MPa条件下,催化剂经6次循环后,DMC收率由15 mmol·g_(CeO_2)~(-1)逐渐降低至2.8 mmol·g_(CeO_2)~(-1),原因归结为反应过程中CeO_2纳米颗粒发生团聚,使暴露出的活性位数量减少。