Annihilation of one of the coexisting attractors in a bistable system

A small change of one of the system parameters may not in general convert a bistable system to a monostable system. However, an external control in the form of a slow periodic parameter modulation can annihilate one of the coexisting states, and thus results in controlled monostability. The annihilation takes place because the state becomes chaotic via the period doubling route and the chaotic state undergoes boundary crisis within a small range of the control amplitude. These features are observed theoretically in two standard models, namely, Henon map and laser rate equations, and confirmed experimentally in a cavity loss modulated CO2 laser.     

Experimental studies on the microstructure and hardness of laser-treated steel specimens

An experimental investigation with 5 kW CW CO₂ laser system was carried out to study the effects of different laser and process parameters on the microstructure and hardness of carbon steel specimen with varying carbon percentage. The laser beam is allowed to scan on the surface of the work piece varying the power (1.1–2.5 kW) and traverse speed (6–15 mm/s) at two different spot sizes using TEM_01* mode laser beam. The most hardenable microstructure achieved in case of three grades of carbon steel and the most influencing parameter on the value of hardness are reported. Besides the above study, some multipass operations are also carried out to recommend an appropriate gap between consecutive passes.     

Thermal conductivity of deep eutectic solvents

Journal of Thermal Analysis and Calorimetry - We have reported the thermal conductivities of three deep eutectic solvents (DESs). We have used choline chloride, N,N-diethyl ethanol ammonium...     

Positron annihilation studies of poly(N‐isopropyl acrylamide) gel in mixed solvents

Positron annihilation lifetime spectroscopy was used to characterize the reentrant volume‐phase‐transition behavior of poly(N‐isopropyl acrylamide) hydrogel in an ethanol/water mixed solvent. The polymer gel was synthesized with γ irradiation. The ortho‐positronium lifetime (τ₃) in the gel slowly increased with an increase in the ethanol content in the mixed solvent. τ₃ was not influenced by the volume phase transition. The ortho‐positronium intensity decreased with the collapse of the gel in an approximately 10% ethanol/water mixture. When swelled in pure ethanol, τ₃ initially increased with the solvent amount in the gel, showing the destruction of intramolecular hydrogen bonding and the relaxation of polymer chains. The lower critical solution temperature of the gel in the 10% ethanol/water mixture was lower than that in pure water, and τ₃ for various solvent contents showed behavior similar to that seen in pure solvent. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1028–1036, 2002     

Kinetics and mechanism of reactions of bis(biguanide)copper(II) ion with 2,2′-bipyridyl and 1,10-phenanthroline in aqueous solution

Summary In aqueous solution [Cu(bigH)₂]²⁺ (bigH=biguanide) reacts with 2,2-bipyridyl (bipy) and 1,10-phenanthroline (phen) through intermediate formation of ternary complexes [Cu(bigH)(L)]²⁺ and [Cu(bipy)(phen)]²⁺ and binary complexes [CuL₂]²⁺ (L=bipy, phen). The rates of the different steps have been followed in borax buffer (pH 8.0±0.1) by stopped-flow spectrophotometry. For each step k_obs=k₀+k_L[L] and the k_L path appears to be associative. H and S values for the k_L path conform to an isokinetic trend.     

Au nanoparticles and polyaniline coated resin beads for simultaneous catalytic oxidation of glucose and colorimetric detection of the product

In this letter, we report the synthesis of Au nanoparticles (NPs) and polyaniline (PANI) on the same cation-exchange resin beads and demonstrate their use in catalyzing the oxidation of glucose to gluconic acid by Au NPs and simultaneously in detecting the formation of the acid by the color change of PANI. The synthesis was carried out by exchanging the cations of the resins with HAuCl4 and anilinuium chloride and then reducing the metal ions by NaBH4 to produce Au NPs followed by polymerization of aniline using H2O2. The green emeraldine salt form of PANI thus obtained was treated with NaOH to be converted to blue emeraldine base before use. The deposition of Au NPs was confirmed by a change in color of the bead, visible spectroscopy, X-ray diffraction, and scanning electron microscopic measurements. On the other hand, the presence of PANI was confirmed by Fourier transform infrared (FTIR) and ultraviolet-visible (UV-vis) spectroscopy. The formation of gluconic acid from glucose was confirmed by FTIR spectroscopy. We could detect the presence of glucose of a minimum 1.0 mM concentration in water, using the present method. Our experimental observations demonstrate the possibility of the incorporation of multifunctional components on the surfaces of resins for carrying out a chemical reaction as well as detection of the product.     

Invariants for normal completely positive maps on the hyperfinite II1 factor

We investigate certain classes of normal completely positive (CP) maps on the hyperfinite II₁ factorA. Using the representation theory of a suitable irrational rotation algebra, we propose some computable invariants for such CP maps. Dedicated to Professor K B Sinha     

1,8-Dihydroxyanthraquinone anchored on silica gel: synthesis and application as solid phase extractant for lead(II), zinc(II) and cadmium(II) prior to their determination by flame atomic absorption spectrometry

A new chelating matrix has been prepared by immobilizing 1,8-dihydroxyanthraquinone (DHAQ) on silica gel modified with (3-aminopropyl)triethoxysilane. After characterizing the matrix with thermogravimetric analysis (TGA), cross polarization magic angle spinning (CPMAS) NMR and diffuse reflectance infrared fourier transformation (DRIFT) spectroscopy, it has been used to preconcentrate Pb(II), Cd(II) and Zn(II) prior to their determination by flame atomic absorption spectrometry. The optimum pH ranges for quantitative sorption are 6.0-7.5, 7.0-8.0 and 6.0-8.0 for Pb, Zn, and Cd, respectively. All the metal ions can be desorbed with 2 mol l(-1) HCl/HNO(3). The sorption capacity of the matrix has been found to be 76.0, 180.0 and 70.2 mumol g(-1) for Pb, Zn and Cd, respectively, with the preconcentration factor of approximately 200. The limits upto which electrolytes NaNO(3), NaCl, NaBr, Na(2)SO(4), Na(3)PO(4) sodium citrate, EDTA, glycine and humic acid and cations Ca(II), Mg(II), Cu(II), Co(II), Ni(II), Mn(II) Al(III), Cr(III) and Fe(III) can co-exist with the metal ions during their sorption without any adverse effect are reported. The lowest concentration of metal ions for quantitative recovery is 5.0 ng ml(-1) The simultaneous enrichment and determination of all the metals is possible if total load of metal ions is less than sorption capacity. The flame AAS was used to determine these metal ions in underground, tap and river water samples (relative standard deviation (R.S.D.)相似文献   

Phase behavior and microstructures of nonionic fluorocarbon surfactant in aqueous systems

The phase behavior and self-assembled structures of perfluoroalkyl sulfonamide ethoxylate, C8F17SO2N(C3H7)(CH2CH2O)20H (abbreviated as C8F 17EO20), a nonionic fluorocarbon surfactant in an aqueous system, has been investigated by the small-angle X-ray scattering (SAXS) technique. The C8F17EO20 forms micelles and different liquid crystal phases depending on the temperature and composition. The fluorocarbon micellar structure induced by temperature or composition change and added fluorocarbon cosurfactant has been systematically studied. The SAXS data were analyzed by the indirect Fourier transformation (IFT) and the generalized indirect Fourier transformation (GIFT) depending on the volume fraction of the surfactant and complemented by plausible model calculations. The C8F17EO20 forms spherical type micelles above critical micelle concentration (cmc) in the dilute region. The micelle tends to grow with temperature; however, the growth is not significant on changing temperature from 15-75 degrees C, which is attributed to the higher clouding temperature of the surfactant (>100 degrees C). On the other hand, the micellar structure (shape and size) is apparently unaffected by composition (1-25 wt %) at 25 degrees C. Nevertheless, addition of fluorocarbon cosurfactant of structure C8F17SO2N(C3H7)(CH2CH2O)H (abbreviated as C8F17EO1) to the semidilute solution of C8F17EO20 (25 wt %) favors micellar growth, which finally leads to the formation of viscoelastic wormlike micelles, as confirmed by rheometry and supported by SAXS. The onset sphere-to-wormlike transition in the structure of micelles in the C8F17EO20/water/C8F17EO1 system is due to the fact that the C8F17EO1 tends to go to the surfactant palisade layer so that the critical packing parameter increases due to a decrease in the effective cross-sectional area of the headgroup. As a result, spherical micelles grow into a cylinder, which after a certain concentration entangle to form a rigid network structure of wormlike micelles.     

Flexible software reliability growth model with testing effort dependent learning process

A lot of importance has been attached to the testing phase of the Software Development Life Cycle (SDLC). It is during this phase it is checked whether the software product meets user requirements or not. Any discrepancies that are identified are removed. But testing needs to be monitored to increase its effectiveness. Software Reliability Growth Models (SRGMs) that specify mathematical relationships between the failure phenomenon and time have proved useful. SRGMs that include factors that affect failure process are more realistic and useful. Software fault detection and removal during the testing phase of SDLC depend on how testing resources (test cases, manpower and time) are used and also on previously identified faults. With this motivation a Non-Homogeneous Poisson Process (NHPP) based SRGM is proposed in this paper which is flexible enough to describe various software failure/reliability curves. Both testing efforts and time dependent fault detection rate (FDR) are considered for software reliability modeling. The time lag between fault identification and removal has also been depicted. The applicability of our model is shown by validating it on software failure data sets obtained from different real software development projects. The comparisons with established models in terms of goodness of fit, the Akaike Information Criterion (AIC), Mean of Squared Errors (MSE), etc. have been presented.