Study on the Superhydrophilicity of the SiO2-TiO2 Thin Films Prepared by Sol-Gel Method at Room Temperature

Nanoscale SiO₂-TiO₂ composite thin films with the thickness of about 100 nm were prepared by sol-gel method at room temperature in air. The chemical states of the elements on the surface and near the surface were measured by XPS. The results showed that the Ti on/near the surface of the thin films existed not only as TiO₂ but also as Ti₂O₃. Part of the TiO₂ was changed to Ti₂O₃ after UV irradiation. The crystalline structure of the TiO₂ in the SiO₂-TiO₂ thin films was anatase with the crystallite size of 14–20 nm. It was found that the thin film prepared at room temperature in air has good superhydrophilic property and has strong adherence to the substrate.     

Behavior of cellulose in NaOH/Urea aqueous solution characterized by light scattering and viscometry

Cellulose was dissolved in 6 wt % NaOH/4 wt % urea aqueous solution, which was proven by a ¹³C NMR spectrum to be a direct solvent of cellulose rather than a derivative aqueous solution system. Dilute solution behavior of cellulose in a NaOH/urea aqueous solution system was examined by laser light scattering and viscometry. The Mark–Houwink equation for cellulose in 6 wt % NaOH/4 wt % urea aqueous solution at 25 °C was [η] = 2.45 × 10^?2 weight‐average molecular weight (M_w)^0.815 (mL g^?1) in the M_w region from 3.2 × 10⁴ to 12.9 × 10⁴. The persistence length (q), molar mass per unit contour length (M_L), and characteristic ratio (C_∞) of cellulose in the dilute solution were 6.0 nm, 350 nm^?1, and 20.9, respectively, which agreed with the Yamakawa–Fujii theory of the wormlike chain. The results indicated that the cellulose molecules exist as semiflexible chains in the aqueous solution and were more extended than in cadoxen. This work provided a novel, simple, and nonpollution solvent system that can be used to investigate the dilute solution properties and molecular weight of cellulose. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 347–353, 2004     

NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.     

高功率LDA紧密侧面抽运Nd:YLF两级双程离轴放大系统实验研究

 介绍了一台10mm口径两级双程离轴放大系统，实现了对5mm×5mm口径光束的激光放大，耦合系统采用高功率LDA紧密侧面直接抽运棒状Nd:YLF方式。分析并实验研究了在不同抽运电流、放大脉冲与放大器LDA抽运时刻的不同延时及不同注入能量条件下，放大系统及光束每次放大时放大特性的规律。实验得到：在放大系统5mm×5mm软光阑处注入1.58mJ能量时，放大系统可输出129.2mJ能量，能量提取效率达到19.5%，满足该系统的设计指标。     

螺旋线径向挤压变形对其慢波结构冷测特性的影响

 介绍了用MAFIA软件的准周期边界条件计算螺旋线行波管慢波结构的色散和耦合阻抗，以及用ANSYS软件对螺旋线径向挤压变形建模的方法，并对螺旋线受挤压径向变形对其冷测特性的影响进行了详细的分析。结果表明:螺旋线径向挤压变形会导致相速增大，而在通常的变形范围内耦合阻抗也会增加；当变形继续增大时耦合阻抗上升到最大值后开始下降。     

利用声波控制超短脉冲的色散

 声光互作用器件声光可编程色散滤波器（AOPDF）是一种实时的色散补偿器件，它可用于飞秒啁啾脉冲放大系统。通过耦合模理论推导，得到了输出脉冲的群延迟与调制声波的频率、啁啾、带宽等参数的关系，并且对用2.5cm长的LiNbO₃作为声光晶体的AOPDF补偿飞秒光脉冲的色散进行了数值模拟，得到了对中心波长为800 mm的钛宝石飞秒激光色散补偿特性及所需声波的频率和啁啾参数。     

30J能量驱动类镍银X光激光的理论研究

 在1.2×10¹³W·cm^－2低功率密度下，对基频激光预主短脉冲驱动类镍银X光激光机理进行了数值模拟和理论分析。证实了在靶长23 mm范围内X光激光都能获得有效放大，取得了和实验相符合的结果。考虑了单柱面镜线聚焦沿靶长度方向功率密度的非均匀性对X光激光放大的影响，采用弯曲靶能有效克服折射以及单柱面镜线聚焦功率密度非均匀带来的不利影响。理论模拟给出的类镍银X光激光的出光下限泵浦功率密度也与实验符合得很好。理论模拟还表明，采用1%左右的预脉冲强度并对预主脉冲时间间隔进行优化，X光激光的输出能量和能量转换效率将获得大幅度提高。     

塑料光纤(POF)的发展及其应用

阐述了阶跃型塑料光纤和渐变型塑料光纤的发展过程及其国内外研究现状,介绍了塑料光纤在局域网、汽车工业、传感器等领域的应用.通过对石英光纤、金属电缆与塑料光纤的性能进行比较,得到了塑料光纤具有芯径大、柔韧性好、价格低廉、制作简单等特点.就塑料光纤在局域网、汽车工业、传感器等领域的应用进行了分析、总结,结果表明降低塑料光纤的传输损耗可以进一步扩大其应用领域.最后分析了我国塑料光纤的研究、生产现状与国际水平的差距,并提出了提高国产塑料光纤技术水平的建议.     

滤片-XRD探测系统响应时间测量

 研究了软X射线能谱仪探测道系统(系统包括X射线二极管（XRD）、SUJ-50-10电缆和不同频带示波器)的响应时间。实验利用上海激光联合实验室的20TW激光器激光(激光能量约20J，脉冲宽度约1ps)打金箔靶产生的X光，用XRD探测系统测量，记录示波器有TK684C，TK694C和WM8500等。将实验数据进行了线性拟合和比对分析。滤片XRD探测系统的响应时间随偏压升高而加快，随传输电缆长度的增加而变慢，因此测量快信号过程时，应提高探测器偏压，缩短传输电缆，选择宽频带高采样率示波器，以便减少系统的响应时间，减小信号失真程度。     

光学非球面二次曲面常数及顶点曲率的研究

受光学非球面制造过程中诸工艺参数的影响,能否保证非球面顶点曲率及二次曲面常数的精度是一个重要问题。基于二次曲面方程,推导出确定光学非球面二次曲面常数k以及顶点曲率半径r的一组算法,并在对一块口径为760mm×200mm标准非球面反射镜的实际测算中进行拟合,经过优化,拟合精度达到Δk=0.015,Δr=0.341mm,从而有效的控制了光学非球面制造过程中的顶点曲率及二次曲面常数的偏差。