Experimental investigation and theoretical modeling of liquid entrainment in a horizontal tee with a vertical-up branch

This article describes a comprehensive literature review of liquid entrainment in horizontal pipes with vertical-up branches. Deficiencies in the available data and correlations were identified. The Air–water Test Loop for Advanced Thermal–hydraulic Studies (ATLATS) was constructed and entrainment onset and steady-state data were collected for a wide range of flow conditions. Using new insights gained from experimental testing, the authors developed a model for predicting the onset of entrainment and steady-state entrainment rate. Previously published correlations, along with the new model, are compared against all available data. The new model shows very good agreement with the onset data, but is not very good at predicting branch quality at high liquid flow rates.     

A laser Doppler anemometry technique for Reynolds stresses measurement

A technique is described for the measurement of all components of mean velocity and Reynolds stresses, in a complex turbulent flow where achieving coincidence data acquisition is difficult. The method is based on data recorded using four orientations of the laser probe. It is shown that the measurement errors are not the same for all the components of the Reynolds tensor, but they are sufficiently small to give a good accuracy. An application to a turbomachinery flow is given to illustrate the method.     

Mesoscopic details of crack tip deformation field by application of differential interference contrast method

An experimental method is developed to examine the near tip deformation at the mesoscopic scale level. The differential interference contrast (DIC) method is used by application of the Nomarski prism in polarized microscope for measuring the out of surface deformation. The method is very sensitive to small height changes detected by different interference color. Discussed are results for the crack tip deformation field.     

Experimental flow study over a blunt-nosed axisymmetric body at incidence

The flowfield over a blunt-nosed cylinder was examined experimentally at a low subsonic speed for Re=1.88×10⁵ and angles of attack up to 40°. Velocity measurements were carried out (employing a seven-hole Pitot tube) as well as wall static pressure and wall shear-stress measurements. Surface flow visualization was applied using liquid crystals and a mixture of oil–TiO₂. For all the examined cases no flow asymmetries were found. For high angles of attack (20° and above) a separation “bubble” appears at the leeside of the nose area (streamwise flow separation). The basic feature of the circumferential pressure distribution at the after body area for these angles of attack is a plateau close to the suction peak and a fast recovery next to it. One streamwise vortex on each side of the symmetry plane is formed as well as a separation bubble about 90° far from this plane, where the cross-flow primary separation line is located. Each cross-flow primary separation line starts at the leeside nose area and moves towards the windward side along the cylindrical after body. The space between the two primary separation lines close to the wall is characterized by high flow fluctuations on the leeside, compared to the low fluctuations of the windward side.     

Decay kinetics of the green emission in tungstates and molybdates

Luminescence characteristics of a number of undoped and variously doped PbWO₄ crystals were studied at 0.4–400 K by the time-resolved spectroscopy and compared with those of ZnWO₄,CdWO₄ and PbMoO₄ crystals. Two types of green emission centres are detected in PbWO₄ crystals. The centres of the first type are responsible for the low-temperature 2.3–2.4 eV emission observed under excitation around 3.90–3.95 eV. The structure and parameters of their relaxed excited states were determined. It was concluded that the origin of defects responsible for the green emission of the first type could vary for different crystals. The centres of the second type with the emission around 2.5 eV appear in crystals containing oxygen vacancies after the thermal destruction of Pb⁺-WO₃ centres at T>180 K. Decomposition of the exciton and various defect-related states was also studied, and activation energies of this process were calculated.     

Rare earth photoionization study by the resonant microwave cavity technique

Photoconductivity spectra of rare earth-doped insulating materials are measured using the resonant microwave cavity method. This technique is based on the detection of the cavity Q-factor changes induced by irradiation of the sample (inserted in the cavity) by a pulsed tunable laser. Results obtained with Lu₂(SiO₄)O:Ce³⁺ and BaF₂:Eu²⁺ are presented and discussed. Photoionization thresholds at 400 nm (3.1 eV) and 310 nm (4.0 eV) are measured for Lu₂(SiO₄)O:Ce³⁺ and BaF₂:Eu²⁺, respectively.     

Electron spin lifetimes in Hg0.78Cd0.22 Te and InSb

We have made direct pump–probe measurements of spin lifetimes in long wavelength narrow-gap semiconductors at wavelengths between 4 and 10 μm and from 4 to 300 K. In particular, we measure remarkably long spin lifetimes, τ_s300 ps, even at 300 K for epilayers of degenerate n-type InSb. In this material the mobility is approximately constant between 77 and 300 K, and we find that τ_s is approximately constant in this temperature range. In order to determine the dominant spin relaxation mechanism we have investigated the temperature dependence of τ_s in non-degenerate lightly n-type Hg_0.78Cd_0.22Te of approximately the same band gap as InSb, and find that τ_s varies from 356 ps at 150 K to 24 ps at 300 K. Our results, both in magnitude and temperature dependence of τ_s, imply that the Elliott–Yafet model dominates in these materials.     

A realistic coronary artery phantom for particle image velocimetry

Myocardial infarction results from the rupture of an atherosclerotic plaque, which occurs in response to both mechanical stress and inflammatory processes. In order experimentally observe flow into atherosclerotic coronary artery morphologies, a novel technique for molding realistic compliant phantom featuring injection-molded inclusions and multiple layers has been developed. This transparent phantom allows for particle image velocimetry (PIV) flow analysis and can supply experimental data to validate computational fluid dynamics algorithms and hypothesis.