热导式热量计特征热谱方程的建立

Based on the interfacial model of a conduction calorimeter, a characteristic thermogram equation is suggested in this paper. Measurements of only two quantities such as the maximum peak height △m and its time tm, enables us to calculate the peak height at any interval by using this model. Thermograms of alkaline hydrolysis of ethyl propionate and ethyl acetate have been measured at 25℃, respectively. The themographic data calculated by using the characteristic thermogram equation are in reasonable agreement with those read from the thermograms.     

银微电极微分电位溶出分析法研究

本文首次报道了银微电极微分电位溶出分析法。用化学刻蚀法方便地制作了银微电极，用于ＤＰＳＡ具有背景值低，分辨率好、精密度及灵敏度高，在不搅拌，仅需一定酸度而酸度而无其它介质的条件下就能测试等优点，对人工试样及自来水样分析，结果令人满意。     

毛细管电泳在拮抗药物对氨基苯甲酸、对羟基苯甲酸和磺胺分析测定中的应用

本文报道了一种用毛细管区带电泳法(CZE)分离与测定对氨基苯甲酸、对羟基苯甲酸及磺胺类药物的新方法.电泳条件为:用 20mmol/L硼砂-20mmol/L H_3PO_4-20 mmol/Lβ-环糊精-4％乙醇(pH 7.0)作电泳液,L-抗坏血酸为内标,280nm为检测波长,样品由电进样方式(10kV/10s)引入毛细管(51.2 cm×50μm i.d.,有效分离长度为 38.5 cm).在24.5°C下,6 min内三者可达基线分离(电泳电压 25kV),且在一定范围内可进行定量分析,保留时间(Tr)及A_(样品)/A_(内标)的RSD值分别小于1.0％和5.0％.本法的建立为研究这三者共存于高等动物及微生物体内时的生理作用提供了一种可共选择的新方法.     

Flow injection spectrofluorimetric determination of reserpine in tablets by on-line acetone sensitized photochemical reaction

On-line photochemical reaction of reserpine in the presence of acetone was investigated. Acetone was found to speed up the on-line photochemical conversion of reserpine into an intensively fluorescent compound. Not only reaction acidity but also the acetate buffer concentration affected the on-line photochemical induced fluorescence signal. Based on the observation an automated flow injection photochemical fluorimetric approach was developed. An injected sample zone was carried by a water stream to be merged with a acetate buffer (pH 3.4) solution containing 0.02% acetone in a knotted PTFE reactor (KR), which was freely coiled around a 6-W low pressure mercury lamp. While passing the KR, reserpine was transformed into an intensively fluorescent compound. It was on-line detected in a flow-through cell at the emission wavelength of 490 nm and excitation wavelength of 386 nm. At optimized conditions, a detection limit 0.45 mug l(-1) was achieved at a sampling rate of 90 h(-1). Eleven determinations of a 0.5 mg l(-1) reserpine standard solution gave a R.S.D. of 0.3%. The linear dynamic range of reserpine calibration curve was 0.01-0.75 mg l(-1). The proposed method was applied to assay the reserpine content in tablets and to monitor the dissolution profile of reserpine tablets. Satisfactory results were obtained for both the assays and dissolution studies.     

Solid-supported synthesis of a peptide beta-turn mimetic

[structure: see text]The solid-supported synthesis of a bicyclic diketopiperazine, a potential peptide beta-turn mimetic, is described. The Ugi reaction between the resin ester of alpha-N-Boc-diaminopropionic acid (an amine input), alpha-bromo acid, aldehyde, and isocyanide is the key step in the proposed protocol.     

Study of transition metal oxide doped LaGaO3 as electrode materials for LSGM-based solid oxide fuel cells

Transition metal oxide doped lanthanum gallates, La_0.9Sr_0.1Ga_0.8M_0.2O₃ (where M=Co, Mn, Cr, Fe, or V), are studied as mixed ionic-electronic conductors (MIECs) for electrode applications. The electrochemical properties of these materials in air and in H₂ are characterized using impedance spectroscopy, open cell voltage measurement, and gas permeation measurement. Three single cells based on La_0.9Sr_0.1Ga_0.8 Mg_0.2O₃ (LSGM) electrolyte (1.13 to 1.65 mm thick) but with different electrode materials are studied under identical conditions to characterize the effectiveness of the lanthanum gallate-based MIECs for electrode applications. At 800 °C, a single cell using La_0.9Sr_0.1- Ga_0.8Co_0.2O₃ as the cathode and La_0.9Sr_0.1Ga_0.8Mn_0.2O₃ as the anode shows a maximum power density of 88 mW/cm², which is better than that of a cell using Pt as both electrodes (20 mW/cm²) and that of a cell using La_0.6Sr_0.4CoO₃ (LSC) as the cathode and CeO₂-Ni as the anode (61 mW/cm²) under identical conditions. The performance of LSGM-based fuel cells with MIEC electrodes may be further improved by reducing the electrolyte thickness and by optimizing the microstructures of the electrodes through processing. Received: 9 January 1998 / Accepted: 1 May 1998     

Plasticization and Crystallization of Poly(ethylene Terephthalate) Induced by Water

Commercial poly(ethylene terephthalate) (PET) was treated at R. H.>80% and room temperature for a set time. The glass transition temperature (Tg) decreases with the time of exposure to high humidity. The decrease in Tg is a result of plasticization. Our data indicate that the Tg of dry PET of 76-78°C may decrease to as low a temperature as 65-67°C when it is wet. Induced crystallization of PET in the presence of water reduces the cold crystallization temperature (Tc). The structure of water-induced crystals is imperfect and can be improved in perfection by annealing. This revised version was published online in July 2006 with corrections to the Cover Date.