New liquid chromatographic-chemometric approach for the determination of sunset yellow and tartrazine in commercial preparation

A new liquid chromatographic (LC)-chemometric approach was developed for the determination of sunset yellow (SUN) and tartrazine (TAR) in commercial preparations. This approach uses LC and chemometric calibration methods, i.e., classical least-squares (CLS), principal component regression (PCR), and partial-least squares (PLS), simultaneously. The combined LC-chemometric approaches, denoted as LC-CLS, LC-PCR, and LC-PLS, are based on photodiode array (PDA) detection at multiple wavelengths. Optimum chromatographic separation of SUN and TAR with allura red as the internal standard (IS) was obtained by using a Waters Symmetry C18 column, 5 microm, 4.6 x 250 mm, and 0.2 M acetate buffer (pH 5)-acetonitrile-methano-bidistilled water (55 + 20 + 15 + 10, v/v) as the mobile phase at a flow rate of 1.9 mL/min. The LC data sets consisting of the ratios of analyte peak areas to the IS peak area were obtained by using PDA detection at 5 wavelengths (465, 470, 475, 480, and 485 nm). LC-chemometric calibrations for SUN and TAR were separately constructed by using the relationship between the peak-area ratio and the training sets for each colorant. LC-chemometric approaches were tested for different synthetic mixtures containing SUN and TAR in the presence of the IS. These LC-chemometric calibrations were applied to a commercial preparation of the 2 colorants. The experimental results of the LC-chemometric approaches were compared with those obtained by a developed classical LC method using single-wavelength detection.     

配合物聚合反应研究──Ⅱ.以二氨基磺磷酸盐配合物合成聚脲

以二氨基磺酸盐配合物合成了一系列主链上合金属元素(Ca,Ni,Co,Cu)的聚脲聚合物。用IR和1HNMR对其结构进行了表征,以TG-DTA研究了其热性能,并讨论了金属元素种类及其含量对聚脲聚合物溶液粘度的影响。     

甲醇在欠电位沉积Ru修饰Pt电极上的催化氧化

采用欠电位沉积(upd)方法在Pt 表面沉积亚单层的Ru制备出upd-Ru/Pt 电极. 通过欠电位沉积前后电极在0.5 mol·L-1 H2SO4溶液中循环伏安图-152 - 128 mV(vs Ag/AgCl)电位范围内对氢区的数值积分确定Pt表面Ru 的覆盖度. 用电化学方法测试了甲醇在upd-Ru/Pt电极上的催化氧化, 并讨论分析了欠电位沉积电位和Ru的表面覆盖度对甲醇氧化的影响. 结果表明, Ru能够欠电位沉积到Pt表面. Pt表面欠电位沉积少量的Ru 即能大大促进甲醇的氧化.只要控制upd-Ru的沉积量, upd-Ru原子就能大大促进甲醇氧化而与沉积电位无关. Ru原子对甲醇氧化的促进作用与Ru和Pt是否形成合金无关, 而取决于Ru 在Pt表面的百分含量.     

Self-assembly and characterization of paclitaxel-loaded N-octyl-O-sulfate chitosan micellar system

N-octyl-O-sulfate chitosan micellar system loaded paclitaxel was prepared by using dialysis method. The critical micelle concentration (CMC) of the modified chitosan was found to be 0.45 mg/ml. Compared with the amount of N-octyl-O-sulfate chitosan, the paclitaxel loading amount in the system was up to 25% (w/w), depending on both of the solvents used in dialysis and the feed weight ratio of paclitaxel to the derivative. The polymeric micelles forming and loading occurred simultaneously in the dialysis process when ethanol and water were utilized as the solvents for paclitaxel and the polymer, respectively. Paclitaxel-loaded micellar system of N-octyl-O-sulfate chitosan was characterized by DSC, WXRD and TEM. TEM photograph revealed that paclitaxel existed as the colloid particulates in ethanol before loading and in the cores of the spherical polymeric micelles after loading. The results of DSC and WXRD indicated that paclitaxel was transferred from the crystalline state to amorphous state after loading. The lyophilized powder of micellar system (25% (w/w) loading) could be reconstituted easily in aqueous media even after 2 months storage at 4 degrees C without the change of paclitaxel entrapment and micelle size. The reconstituted solution (2.1 mg paclitaxel/ml) also showed good stability. The dilution with saline may decrease the loading and physical stability based on the dilution times which was related with CMC of the polymer. In vitro tests showed that paclitaxel was slowly released from micellar solution and the release lasted up to 220 h by means of the dialysis method.     

Solvent extraction behaviour of iodine and bromine in aqueous-organic systems,analogy with radioactive decay

The extraction of iodine and bromine under various conditions from their saturated aqueous solutions by CCl₄, C₆H₆ and o-xylene has been studied. The data obtained from the experiments carried out at various temperatures, for H₂O(I₂)−CCl₄ and H₂O(I₂)−C₆H₆ systems, exhibit an Arrhenius behaviour. The overall activation energy calculated for the extraction in the H₂O(I₂)−CCl₄ system, 650±50 cal·mol⁻¹ is lower than that of H₂O(I₂)−C₆H₆, 3600±300 cal·mol⁻¹. The use of the solubility parameter for the interpretation of the data in the extraction of iodine is investigated. The data obtained in multiple extractions are treated by using the analogy between extraction and radioactive decay. The half number of extraction for each system is determined. The complex curves obtained in the H₂O(I₂)−CCl₄ and H₂O(I₂) −Br₂)−CCl₄ systems are resolved into two components.     

Single-site mutation and secondary structure stability: an isodesmic reaction approach. The case of unnatural amino acid mutagenesis Ala-->Lac

A method is described to evaluate backbone interactions in proteins via computational unnatural amino acid mutagenesis. Several N-acetyl polyalanyl amides (AcA(n)NH(2)) were optimized in the representative helical (3(10)-, 4(13)-, and a "hybrid" kappa-helix, n = 7, 9, 10, 14) and hairpin (two- and three-stranded antiparallel beta-sheets with type I turns betaalphaalphaepsilon, n = 6, 9, 10) conformations, and extended conformers of N-acetyl polyalanyl methylamides (n = 2, 3) were used to derive multistranded beta-sheet fragments. Subsequently, each residue of every model structure was substituted, one at a time, with l-lactic acid. The resulting mutant structures were again optimized, and group-transfer energies DeltaE(GT) were obtained as heats of the isodesmic reactions: AcA(n)NHR + AcOMe --> AcA(x)LacA(y)NHR + AcNHMe (R = H, CH(3)). These group-transfer energies correlate with the degree of charge polarization of the substituted peptide linkages as measured by the difference Deltae in H and O Mulliken populations in HN-C=O and with the H-bond distances in the "wild-type" structures. A good correlation obtains for the HF/3-21G and B3LYP/6-31G* group-transfer energies. The destabilization effects are interpreted in terms of loss of interstrand and intrastrand H-bonds, decrease in Lewis basicity of the C=O group, and O...O repulsion. On the basis of several comparisons of Ala --> Lac DeltaE(GT)'s with heats of the NH --> CH(2) substitutions, the latter contribution is estimated (B3LYP/6-31G*) to range between 1.5 and 2.4 kcal mol(-1), a figure close to the recent experimental DeltaDeltaG(o) value of 2.6 kcal mol(-1) (McComas, C. C.; Crowley, B. M.; Boger, D. L. J. Am.Chem. Soc. 2003, 125, 9314). The partitioning yields the following maximum values of the electronic association energy of H-bonds in the examined sample of model structures (B3LYP/6-31G* estimates): 3(10)-helix D(e) = -1.7 kcal mol(-1), alpha-helix D(e) = -3.8 kcal mol(-1), beta-sheet D(e) = -6.1 kcal mol(-1). The premise of experimental evaluations of the backbone-backbone H-bonding that Ala --> Lac substitution in proteins is isosteric (e.g., Koh, J. T.; Cornish, V. W.; Schultz, P. G. Biochemistry 1997, 36, 11314) is often but not always corroborated. Examination of the integrity of H-bonding pattern and phi(i), psi(i) distribution identified several mutants with significant distortions of the "wild-type" structure resulting inter alia from the transitions between i, i + 3 and i, i + 4 H-bonding in helices, observed previously in the crystallographic studies of depsipeptides (Ohyama, T.; Oku, H.; Hiroki, A.; Maekawa, Y.; Yoshida, M.; Katakai, R. Biopolymers 2000, 54, 375; Karle, I. L.; Das, C.; Balaram, P. Biopolymers 2001, 59, 276). Thus, the isodesmic reaction approach provides a simple way to gauge how conformation of the polypeptide chain and dimensions of the H-bonding network affect the strength of backbone-backbone C=O...HN bonds. The results indicate that the stabilization provided by such interactions increases on going from 3(10)-helix to alpha-helix to beta-sheet.     

Synthesis of persulfate containing poly (N-vinyl-2-pyrrolidone) (PVP) hydrogels in aqueous solutions by γ-induced radiation

The effect of ⁶⁰Co γ-irradiation on aqueous solutions of poly(N-vinyl-2-pyrrolidone) (PVP) in the presence of persulfate anion has been investigated. The gelation dose of PVP and persulfate containing PVP aqueous solutions has been determined. At low concentrations of persulfate (1.00–3.50%), gelation percentages exhibited a decreasing trend by increasing persulfate content in aqueous solutions of the polymer. The gelation doses of persulfate containing polymer solutions were calculated by the Charlesby–Pinner equation. It was observed that the gelation dose values were shifted to higher values by increasing persulfate concentration in solution. The ratio of the chain scission and crosslinking yields (G(s)/G(x)) was also determined. The results showed that the G(s)/G(x) ratios were smaller than one for PVP aqueous solution system, whereas those obtained for persulfate containing PVP aqueous solutions were higher than unity. The results implied that the chain scission of polymer is more effective than crosslinking in the presence of persulfate. Mechanism of the crosslinking and/or degradation and structure–property relationship of PVP and PVP/persulfate hydrogel systems were investigated by Fourier transformation infeared and thermal analysis (differential scanning calorimetry, thermal gravimetric analysis and differential thermai analysis) methods.     

Structure of starch-bentonite gels

Mixed gels of starch and bentonite are investigated in the interval 0.056–0.089 of total solids/water ratio and 0-100% starch in the solids. The bentonite was a sodium calcium bentonite with a Na/Ca ratio of 1.76. In water it forms gels consisting of a network of band-type structures. Starch forms gels through hydrogen bonds between granules and/or amylose and amylopectin present on the external surfaces of granules and/or in fully stretched form. Mixed gels of bentonite and starch were obtained by adding corn starch granules to the already formed bentonite gels and heating the mixture above the Kofler gelatinization temperature. Amylose and amylopectin were adsorbed on strands of band-type structures of mont-morillonite lamellae. Starch gellation, e.g. diffusion of amylose out of the granule, was facilitated in the presence of bentonite. On the other hand, the presence of starch favored delamination of the montmorillonite particle into thinner lamellae. Maximum gelatinization and polymer adsorption were observed for gels with 20% starch and 80% bentonite. Montmorillonite networks formed the continuous phase for 0-80% starch. At higher starch concentrations, montmorillonite flakes were dispersed within the polymer network. Increase in the water content of the gels caused segregation of the bentonite and starch.     

An extended two‐dimensional copper–molybdate compound with mixed dicarboxyl and organodiamine ligands

The title complex, poly[di‐μ₃‐oxo‐hepta‐μ₂‐oxo‐tetra­oxo­bis(1,10‐phenanthroline)‐μ₄‐terephthalato‐dicopper(II)­tetra­molybdate(VI)], [Cu₂Mo₄(C₈H₄O₄)O₁₃(C₁₂H₈N₂)₂], represents a novel two‐dimensional copper–molybdate compound with mixed ligands. Tetra­nuclear molybdenum oxide clusters are joined through corner‐sharing into a ribbon‐like chain, with [Cu(phen)]²⁺ (phen is 1,10‐phenanthroline) complexes grafted onto either side. The terephthalate ligand lies about an inversion centre and links these chains to form a layer via Cu—O and Mo—O bonds. Face‐to‐face π–π stacking inter­actions between adjacent phen ligands stabilize the structure.     

5，10，15，20-四 [4-(4''-乙基哌嗪基)苯基]卟啉的合成及其与DNA的相互作用

基于卟啉对癌细胞的特殊亲和作用和哌嗪化合物的抗肿瘤、抗病毒作用，设计并合成了具有哌嗪结构的新型卟啉化合物5，10，15，20-四[4-(4'-乙基哌嗪基)苯基]卟啉（TEPPPH₂），其结构经UV-Vis, 元素分析，¹H NMR等手段证明。采用UV-Vis光谱和荧光光谱研究了TEPPPH₂和小牛胸腺DNA 的相互作用模式和结合机理。实验发现，TEPPPH₂能嵌入到DNA的碱基对中，1个小牛胸腺DNA分子对TEPPPH₂分子的最大结合数n约为88，结合常数为8.4×10⁶mol•L^-1 。TEPPPH₂与DNA的结合数和结合常数大于已知的四（4-N-甲基吡啶基）卟啉和Ca/sal-his、Ni/sal–aln型席夫碱抗癌药物。