A rapid heating and high magnetic field thermal analysis technique

Journal of Thermal Analysis and Calorimetry - A new thermal analysis technique is described that allows measurements to be performed on bulk samples at extreme heating and cooling rates and in high...     

Photophysics of Fluorescent Contact Sensors Based on the Dicyanodihydrofuran Motif

Fluorescent molecular rotors have been used for measurements of local mobility on molecular length scales, for example to determine viscosity, and for the visualization of contact between two surfaces. In the present work, we deepen our insight into the excited-state deactivation kinetics and mechanics of dicyanodihydrofuran-based molecular rotors. We extend the scope of the use of this class of rotors for contact sensing with a red-shifted member of the family. This allows for contact detection with a range of excitation wavelengths up to ∼600 nm. Steady-state fluorescence shows that the fluorescence quantum yield of these rotors depends not only on the rigidity of their environment, but – under certain conditions – also on its polarity. While excited state decay via rotation about the exocyclic double bond is rapid in nonpolar solvents and twisting of a single bond allows for fast decay in polar solvents, the barriers for both processes are significant in solvents of intermediate polarity. This effect may also occur in other molecular rotors, and it should be considered when applying such molecules as local mobility probes.     

Influence of Ga/(Ga + In) grading on deep‐defect states of Cu(In,Ga)Se2 solar cells

The benefits of gallium (Ga) grading on Cu(In,Ga)Se₂ (CIGS) solar cell performance are demonstrated by comparing with ungraded CIGS cells. Using drive‐level capacitance profiling (DLCP) and admittance spectroscopy (AS) analyses, we show the influence of Ga grading on the spatial variation of deep defects, free‐carrier densities in the CIGS absorber, and their impact on the cell's open‐circuit voltage V_oc. The parameter most constraining the cell's V_oc is found to be the deep‐defect density close to the space charge region (SCR). In ungraded devices, high deep‐defect concentrations (4.2 × 10¹⁶cm^–3) were observed near the SCR, offering a source for Shockley–Read–Hall recombination, reducing the cell's V_oc. In graded devices, the deep‐defect densities near the SCR decreased by one order of magnitude (2.5 × 10¹⁵ cm^–3) for back surface graded devices, and almost two orders of magnitude (8.6 × 10¹⁴ cm^–3) for double surface graded devices, enhancing the cell's V_oc. In compositionally graded devices, the free‐carrier density in the absorber's bulk decreased in tandem with the ratio of gallium to gallium plus indium ratio GGI = Ga/(Ga + In), increasing the activation energy, hindering the ionization of the defect states at room temperature and enhancing their role as recombination centers within the energy band. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Growth Actuated Bending and Twisting of Single Crystals

Crystals of a variety of substances including elements, minerals, simple salts, organic molecular crystals, and high polymers forgo long‐range translational order by twisting and bending as they grow. These deviations have been observed in crystals ranging in size from nanometers to centimeters. How and why so many materials choose dramatic non‐crystallographic distortions is analyzed, with an emphasis on crystal chemistries that give rise to stresses operating either on surfaces of crystallites or within the bulk.     

The Effect of α-Branched Side Chains on the Structural and Opto-Electronic Properties of Poly(Diketopyrrolopyrrole-alt-Terthiophene)

Introducing solubilizing α-branched alkyl chains on a poly(diketopyrrolopyrrole-alt-terthiophene) results in a dramatic change of the structural, optical, and electronic properties compared to the isomeric polymer carrying β-branched alkyl side chains. When branched at the α-position the alkyl substituent creates a steric hindrance that reduces the tendency of the polymer to π–π stack and endows the material with a much higher solubility in common organic solvents. The wider π–π stacking and reduced tendency to crystallize, evidenced from grazing-incidence wide-angle X-ray scattering, result in a wider optical band gap in the solid state. In solar cells with a fullerene acceptor, the α-branched isomer affords a higher open-circuit voltage, but an overall lower power conversion efficiency as a result of a too well-mixed nanomorphology. Due its reduced π–π stacking, the α-branched isomer fluoresces and affords near-infrared light-emitting diodes emitting at 820 nm.     

Polymer Nanocontainers for Intracellular Delivery

Carriers for intracellular delivery are required to overcome limitations of therapeutic agents such as low specificity, systemic toxicity, high clearance rate, and low therapeutic index. Nanocontainers comprised of an aqueous core and a polymer shell have received increasing attention because they readily combine stimuli response to improve intracellular payload release and surface modification to enhance selectivity towards the desired region of action. This Minireview summarizes the design and properties of polymer nanocontainers for intracellular delivery, classified according to the polymer architecture.     

An Arylazopyrazole‐Based N‐Heterocyclic Carbene as a Photoswitch on Gold Surfaces: Light‐Switchable Wettability,Work Function,and Conductance

A novel photoresponsive and fully conjugated N‐heterocyclic carbene (NHC) has been synthesized that combines the excellent photophysical properties of arylazopyrazoles (AAPs) with an NHC that acts as a robust surface anchor (AAP‐BIMe). The formation of self‐assembled monolayers (SAMs) on gold was proven by ToF‐SIMS and XPS, and the organic film displayed a very high stability at elevated temperatures. This stability was also reflected in a high desorption energy, which was determined by temperature‐programmed SIMS measurements. E‐/Z‐AAP‐BIMe@Au photoisomerization resulted in reversible alterations of the surface energy (i.e. wettability), the surface potential (i.e. work function), and the conductance (i.e. resistance). The effects could be explained by the difference in the dipole moment of the isomers. Furthermore, sequential application of a dummy ligand by microcontact printing and subsequent backfilling with AAP‐BIMe allowed its patterning on gold. To the best of our knowledge, this is the first example of a photoswitchable NHC on a gold surface. These properties of AAP‐BIMe@Au illustrate its suitability as a molecular switch for electronic devices.     

Monte Carlo simulation of the chain length distribution in pulsed-laser polymerization experiments in microemulsion

The Monte Carlo method has been used for numerically simulating pulsed-laser polymerization (PLP) in microemulsion, in order to establish if a shift from inflection point to peak maximum as the best measure of the propagation rate constant, k_p, will occur theoretically. Termination is assumed to be instantaneous in the simulations as droplet sizes can be very small in microemulsions. From the results of the simulations it is found that instantaneous termination indeed causes the peak maximum to become the best measure of k_p. From these results it can be deduced that in bulk it is not simply the Poisson-broadening that causes the peak maximum to yield an overestimation of k_p. This overestimation is rather caused by the fact that the termination rate is finite leading to an asymmetrical peak in the molecular weight distribution. In combination with broadening this yields the inflection point to be the best measure of k_p in the bulk.