1.2 Anorganische analyse

Ohne Zusammenfassung     

Quantification of midodrine and its active metabolite in plasma using a high performance liquid chromatography column switching technique

An automated column-switching HPLC system is described for the simultaneous determination of midodrine, an alpha-adrenergic stimulating drug, and its active metabolite, ST-1059. Serum or plasma (850 microliters) is directly injected onto a RP18 (30 micrograms particle size) pre-column (9 x 4 mm ID) which acts as an on-line liquid-solid extractor and analyte enrichment system. The injection is followed by washing steps. The fraction containing the analytes is transferred onto an analytical RP18 column via step gradient elution where the final analysis is performed. Fluorescence detection is used (lambda ex 290 nm and lambda em 322 nm), and method detection limits of 0.8 ng/mL plasma were reached. These were sufficiently low to determine the plasma concentration-time profiles for both compounds following oral administration of 2.5 mg and 5 mg midodrine hydrochloride. The assay in serum or plasma was linear in the range of 1 to 15 ng analyte/mL, the recovery was greater than 95%, and the reproducibility was sufficient. The assay was rugged and was maintained by routinely changing the home-made, dry packed pre-column every 20th serum injection.     

Coercivity analysis in R17Fe83−χBχ magnets

We studied the coercivity in magnets of composition R₁₇Fe_83−χB_χ (R = Nd, Pr and χ = 8, 30), using measurements of the coercive field H_c, its angular dependence, and the magnetic viscosity coefficient S_v, for temperatures between 4.2 and 500 K. The results are discussed in relation to a model which does not specifically consider the detailed mechanisms involved in magnetization reversal, but which provides information about the magnetic properties in the activation volume v where magnetization reversal is initiated. It is concluded that the ordering temperature in v tends to be slightly smaller than in the bulk and that the room temperature anisotropy in v is not strongly reduced with respect to the bulk value. Finally, a direct evaluation of the dipolar interactions is in good agreement with results obtained from H_c(T).     

Ferroelectric polarization switching in nylon-11

Cold-drawn Nylon-11 films, which were prepared by stretching the melt-quenched films to a draw ratio of 2.8: 1 at room temperature, were found to exhibit an electric displacement versus electric field hysteresis loop. The results confirmed that the Nylon-11 film exhibited ferroelectric behavior at or below room temperature. The coercive fields were 65, 98, 125, 160, and 215 MV/m at 20, 0, ?20, ?40, and ?60°C and the remanent polarization at ?20°C (where there was considerably less dc conduction) was 56 mC/m². Switching of the polarization was almost completed within 20 ms.     

AUTOMATED WIND TUNNEL MEASUREMENTS

It is common practice in power transmission to use bundled overhead electrical conductors because the lower rate of corona discharge, compared with single conductors, makes the bundle attractive for high voltages. However, secondary problems may arise from the vibrations induced by the aerodynamic forces which act on the leeward conductors as a result of their immersion in the wake of a windward conductor. Thus, in addition to possible aeolian and galloping oscillations observed for a single conductor, bundle conductors may also be subjected to wake-induced oscillations. ^1,2 Although extensive research has been done on the aeroelastic behavior of single and bundled conductors which are bare, little is known about the galloping or wake oscillation characteristics of given bundle conductors which, depending upon the environmental conditions during the formation of ice, may have five or so representative shaped cross-sections. One important task involves the aerodynamic quasi-static force and moment measurements in a wind tunnel using full scale conductor cross-sections each of which must be rotated through many angles at different spacings. Such measurements are repetitive as well as tediously time consuming and, hence, are beneficially automated. A reliable, accurate and inexpensive automated apparatus is described in this paper which permits the aerodynamic measurements to be performed efficiently and without intervention. Most importantly, it relieves the operator of the usual responsibility for manually controlling the separation and orientation of the sections as well as the need to manually compensate fluctuations in the free stream air speed. For simplicity, the apparatus is detailed in the context of a twin bundle conductor.