Synthesis of soluble aromatic polyesteramides by stepwise copolycondensation of bisphenols and aromatic diamines with diphenyl chlorophosphate in pyridine

The reaction promoted by diphenyl chlorophosphate (DPCP) in pyridine was successfully applied to the preparation of soluble aromatic copolyesteramides of high molecular weights directly from aromatic dicarboxylic acids, bisphenols, and a wide range of mol % aromatic diamines. Dropwise addition of a mixture of bisphenols and diamines (more favorably of bisphenols and then diamines) to the mixture of dicarboxylic acids activated by DPCP led the reactions homogeneously even with high mol % of diamines to produce copolymers of good solubility. This improved copolymer solubility was roughly estimated by sequence distribution of polyamide and polyester units in the copolymers, which was studied in a model reaction and in the copolycondensations by simultaneous and stepwise addition of bisphenols and diamines.     

Effects of Al concentration and resulting long-period superstructures on the plastic properties at room temperature of Al-rich TiAl single crystals

The role of Al₅Ti₃ and h-Al₂Ti long-period superstructures on the plastic properties of TiAl at room temperature is investigated on five single crystals with aluminium content comprised between 54.7 at.%, and 62.5 at.%. After annealing at 1200°C for 1?h, the Al₅Ti₃ superstructure develops in the L1₀ (γ) matrix upon increasing Al concentration except for Ti–62.5 at.%Al where h-Al₂Ti substitutes for Al₅Ti₃. The CRSS for <110]{111} first increases abruptly with the development of the Al₅Ti₃-type ordering. Then, the CRSS reaches a plateau at which dislocations assemble in groups of four to prevent extra anti-phase boundary (APB) from being engendered during glide throughout the Al₅Ti₃ phase. In Ti–62.5 at.%Al, the CRSS for ordinary slip further increases upon the precipitation of h-Al₂Ti in the L1₀ phase, whereas it decreases when the crystal is fully transformed into single-phased Al₅Ti₃. <101] superlattice dislocations are primarily activated under both the [210] and [1?1?8.6] load orientations irrespective of the Al concentration, but the dislocation microstructure strongly depends on orientation as well as on the degree of Al₅Ti₃ ordering. In the [210] orientation, the frequency of the decomposition of <101] dislocations into 1/2<110] and 1/2<112] dislocations decreases abruptly with the development of Al₅Ti₃. This is interpreted in terms of the increased difficulty to move ordinary dislocations. Under the [1?1?8.6] orientation, the density of faulted dipoles diminishes remarkably with the development of Al₅Ti₃. This is consistent with the transformation of the low energy extrinsic stacking fault of the L1₀ phase into a higher energy complex extrinsic stacking fault.     

Synthetic Studies on Sialoglycoconjugates 22: Total Synthesis of Tumor-Associated Ganglioside,Sialyl Lewis X1

ABSTRACT

The first total synthesis of tumor-associated glycolipid antigen, sialyl Lewis X is described. Glycosylation of 2-(trimethylsilyl)ethyl O-(2-acetamido-4,6-O-benzylidene-2-deoxy-β-D-glucopyranosyl)-(1→3)-O-(2,4,6-tri-O-benzyl-β-D-galactopyranosyl)-(1→4)-2,3,6-tri-O-benzyl-β-D-glucopyranoside (1) with methyl 2,3,4-tri-O-benzyl-1-thio-β-L-fuco-pyranoside (4) gave the α-glycoside (5), which was converted by reductive ring-opening of the benzylidene acetal into the glycosyl acceptor (6). Dimethyl(methylthio)sulfonium triflate-promoted coupling of 6 with methyl O-(methyl 5-acetamido-4,7,8,9-tetra-O-acetyl-3,5-dideoxy-D-glycero-α-D-galacto-2-nonulopyranosylonate)-(2→3)-2,4,6-tri-O-benzoyl-1-thio-β-D-galactopyranoside (7) afforded the desired hexasaccharide 8 in good yield. Compound 8 was converted into the α-trichloroacetimidate 11, via reductive removal of the benzyl groups, O-acetylation, removal of the 2-(trimethylsilyl)ethyl group, and treatment with trichloroacetonitrile, which, on coupling with (2S, 3R, 4E)-2-azido-3-O-benzoyl-4-octa-decene-1,3-diol (12), gave the β-glycoside 13. Finally, 13 was transformed, via selective reduction of the azide group, condensation with octadecanoic acid, O-deacylation, and hydrolysis of the methyl ester group, into the title compound 16.     

Dynamical study of femtosecond-laser-ablated liquid-aluminum nanoparticles using spatiotemporally resolved x-ray-absorption fine-structure spectroscopy

We study the temperature evolution of aluminum nanoparticles generated by femtosecond laser ablation with spatiotemporally resolved x-ray-absorption fine-structure spectroscopy. We successfully identify the nanoparticles based on the L-edge absorption fine structure of the ablation plume in combination with the dependence of the edge structure on the irradiation intensity and the expansion velocity of the plume. In particular, we show that the lattice temperature of the nanoparticles is estimated from the L-edge slope, and that its spatial dependence reflects the cooling of the nanoparticles during plume expansion. The results reveal that the emitted nanoparticles travel in a vacuum as a condensed liquid phase with a lattice temperature of about 2500 to 4200 K in the early stage of plume expansion.     

Rearrangement of 6,7-dithiabicyclo[3.1.1]heptane 6-oxides to a 7,8-dithia-6-oxabicyclo[3.2.1]octane catalyzed by montmorillonite K 10

Treatment of 2,2,4,4-tetramethyl-1,5-diphenyl-6,7-dithiabicyclo[3.1.1]heptane 6-endo-oxide ( 2 ) with Montmorillonitc K 10 in dichloromethane gave 2,2,-4,4-tetramethyl-1,5-diphenyl-7,8-dithia-6-oxabicyclo-[3.2.1]octane ( 6 ) (11%) with recovery of 2 (87%). Under similar reaction conditions, the 6-exo-oxide 7 and the sulfenate 6 gave a mixture of 6 (21%), 2 (67%), and 7 (9%) and a mixture of 2 (89%) and 6 (9%), respectively. These results indicate the relative thermodynamic stabilities of the three compounds to be 2 > 6 > 7 . PM3 calculations on these compounds showed the heats of formation (kcal/mol) to be in the following order: 6 (44.12783), 2 (57.46721), and 7 (59.37918). The driving force of this unusual 1,2-rearrangement of 2 and 7 to 6 would be the release of the ring strain of the bicyclo[3.1.1]heptane system of 2 and 7 by ring expansion.     

Stereospecific and asymmetric polymerization of 1-phenyldibenzosuberyl methacrylate with radical and anionic initiators

Stereospecific and asymmetric (helix-sense-selective) polymerization of 1-phenyldibenzosuberyl methacrylate (PDBSMA) was performed with radical and anionic initiators. A highly isotactic polymer having triad isotacticity greater than 97% was obtained by radical polymerization with (i-PrOCOO)₂ at 40°C. The radical polymerization of PDBSMA in (+)- and (-)-menthol gave (-)-and (+)-polymers, respectively, whose optical activity is ascribed to the prevailing one-handed helical conformation of a polymer chain. The radical copolymerization of PDBSMA with a small amount of an optically active monomer, (+)-phenyl-2-pyridyl-o-tolylmethyl methacrylate, afforded an optically active copolymer with the prevailing one-handed helical structure of PDBSMA sequences. Asymmetric anionic polymerization of PDBSMA was carried out with the complex of N, N′-diphenylethylenediamine monolithium amide and a chiral ligand, (+)-1-(2-pyrrolidinylmethyl)pyrrolidine in toluene at −78°C. The obtained polymer was highly isotactic and optically active due to nearly 100% one-handed helical structure.     

Poly(2,5-dimethoxyaniline) film coating for corrosion protection of iron

A poly(2,5-dimethoxyaniline) (PDMA) film was coated on the iron surface by the electropolymerization of 2,5-dimethoxyaniline in neutral buffer solution (pH?6.86). The PDMA film strongly adhered to the surface because of the polar methoxy groups of the PDMA molecules. The fact that no electrochemical response of the PDMA film-coated iron electrode to dissolved Fe²⁺ exhibited that the PDMA film was less permeable to dissolved species, acting as a diffusion barrier against agents causing corrosion such as H₂O and O₂. The PDMA film coating greatly lowered the anodic current peak ascribed to the anodic dissolution of iron and the corrosion current in strongly acidic medium, 0.5?M H₂SO₄ aqueous solution (1?M?????mol?dm^??) as well as neutral medium (pH?6.86). The high anti-corrosion ability was due to a hybrid effect of the PDMA film not only as the diffusion barrier, but also as an in situ oxidant in spite of the slight redox activity of PDMA. In addition, the PDMA film is much more durable and adhesive than polyaniline film against over-oxidation.     

Performance Test of CW 300?GHz Gyrotron FU CW I

A 300 GHz CW gyrotron FU CW I has been developed and installed in the Research Center for Development of Far-Infrared Region, University of Fukui as a power source of a high frequency material processing system. Its performance was tested and the maximum power of 1.75 kW / CW has been attained at the beam voltage of 15 kV and the beam current of 1A. The maximum window power efficiency of 15.5% has been obtained at the cathode voltage slightly lower than 15 kV. This gyrotron is designed to deliver a Gaussian beam after mode conversion from the oscillation mode TE_22,8 in the cavity with a complex of an internal radiator and beam shaping mirrors. The detailed measurement with an infrared camera has confirmed that a Gaussian beam is radiated when the magnetic field strength B _c at the cavity is adjusted at a proper value. However, within a range of B _c , the output power is emerged into multiple directions, which suggests simultaneous oscillation of competing cavity modes.