Optical corrosion meter

In a previous study, a mathematical model relating surface and bulk behaviours of metals in aqueous solution has been developed. The model was established based on principles of holographic interferometry for measuring microsurface dissolution, i.e. mass loss, and on those of electrochemistry for measuring the bulk electronic current, i.e. corrosion current. In the present work, an optical corrosion meter was built based on the above model. The corrosion meter consists of an electrochemical cell in which the sample is immersed in aqueous solution. Furthermore, the corrosion meter has a holographic camera with a thermoplastic film for in situ processing of holograms in order to obtain real-time holographic interferoms of the sample in the electrochemical cell. Results of the present work indicate that optical holography is a very useful technique for measuring the corrosion current density of different alloys in aqueous solutions. As a result, the corrosion current density of aluminium, stainless steel, and low-carbon steel in 1 M KCl, 1 M NaCl, and 1 M NaOH solutions were obtained. A comparison between the corrosion data of samples showed that the corrosion current density of the stainless steel in 1 M NaCl is nearly three-folds higher than that of the aluminium in 1 M KCl and the low-carbon steel in 1 M NaOH.     

New critical dimensions forq-deformed bosonic string

Applying the mass shell condition forq-deformed open and closed strings, new critical space-time dimensions are derived. Supported by the Algerian Ministry of High Education and Research under contract N^oD2501/17/01/93. Permanent address.     

The gas dynamics of current-limiting devices during immobility time

The aim of this paper is to extend our knowledge about the gas-dynamic processes in arcs during immobility time. For this purpose, the conservation equations in a magnetohydrodynamic approximation were coupled with the thermochemical and Maxwell equations. Special features arc the introduction of dissociation and ionization of nitrogen and oxygen, and the simultaneous calculation of the distributions of current density and magnetic induction in the arc. Numerical calculations were performed with a reduced two-dimensional (2-D) time-dependent model. Results of the calculations were compared with measurements. The development in time of the measured and calculated are voltage and arc chamber pressure show very good agreement. The pumping effect of the double vortex in the arc region was confirmed by optical measurements. It is concluded that the three-layer model is a good representation for the main physical features during the immobility time, and that the presence of highly conducting gas in the downstream region of the arc is essential for its downstream movement     

Photodiffraction in InGaAs/InGaAsP multiple quantum wells enclosed in a microcavity

We report new results on the diffraction properties of photoinduced gratings in InGaAs/InGaAsP MQW structures. The original feature of this device is that the QWs are enclosed in an asymmetric Fabry–Perot microcavity in order to increase the diffraction efficiency. We observe oscillations in the diffraction efficiency due to resonant effects in the microcavity. The experimental spectra are compared with theory. Diffraction efficiency at 1.55 μm attains a maximum value of 2.7% at a write beam fluence of 260 μ J cm⁻², and then decreases at higher fluences. We explain this phenomenon by an absorption saturation at high excitation.     

EPMA of interfaces applied to the solid oxide fuel cell

Chemical interactions at the phase boundaries of materials applied for the solid oxide fuel cell (SOFC) have been studied by EPMA. The chemical reactivity at the interface of La_y-xSr_xMnO₃/ZrO₂-Y₂O₃ is dependent on the stoichiometry (y) and the Sr content (x) of the perovskite. Typical reaction products (zirconates) and a diffusion zone in the ZrO₂–Y₂O₃ have been observed. The extension of cation release (Mn) is related to the increasing chemical activity of Mn oxide in the perovskite by the Sr substitution for La. The wettability of the metal/oxide interface in the anode cermet (Ni/ZrO₂–Y₂O₃) has been found to be influenced by chemical reactions resulting from the applied reducing atmosphere with high carbon activity. The disintegration of ZrO₂–Y₂O₃ in contact with molten Ni or Ni-Ti and Ni-Cr alloys leads to the redeposition of Y₂O₃-enriched oxides and also to Zr-rich intermetallic compounds and eutectics.     

Toughening of epoxies via craze-like damage

The fracture behavior of a core-shell rubber (CSR) modified epoxy is investigated using both fracture mechanics and microscopy tools. The CSR-modified epoxy is found to be toughened via numerous line-array cavitations of the CSR particles, followed by plastic flow of the epoxy matrix. The toughening effect via the above craze-like damage process is found to be as effective as that of the well-known widespread rubber cavitation/matrix shear yielding mechanisms. The conditions for triggering the craze-like damage appear to be both stress state and rubber concentration dependent. The type of rubber tougheners utilized also plays a critical role in triggering this rather unusual craze-like damage in epoxy systems. © 1993 John Wiley & Sons, Inc.