新型阵列式片状放大器全口径增益分布均匀性实验研究

利用CCD增益测试系统对一台闪光灯抽运、通光口径为 2 9cm× 2 9cm的新型高功率固体激光阵列式片状放大器的增益分布进行了实验测试 ,在充电电压为 2 3kV、抽运能密度为 11J/cm3 的条件下 ,新型 4× 2× 3阵列式片状放大器全口径范围内的小信号增益系数的峰值与平均值之比为 1.10∶1。     

激光钝化对熔石英修复后损伤性能影响的实验研究

采用10.6 μupm 的 CO₂激光, 对单次激光脉冲辐照修复熔石英存在的烧蚀采用大光斑钝化去除. 经过辐照修复的区域置于前表面测试初始损伤阈值, 结果表明调制造成的损伤得到了一定程度的抑制; 辐照区域置于后表面修复后 熔石英的初始损伤阈值超过了基底的初始损伤阈值. 实验观察到了应力分布外扩, 同时明显减弱. 对损伤增长的测试说明, 经过激光熔融辐照后的损伤点, 当应力释放以后, 损伤扩展初期表现出指数增长趋势, 后期随着辐照次数的增加, 损伤增长不再明显, 并且趋于恒定值.     

Bright blue photoluminescence from a mixed tin and manganese oxide xerogel prepared via solben hydrothermalben gel process

A new blue photoluminescent material, a mixed tin and manganese oxide xerogel, is prepared via sol-hydrothermal-gel process assisted by citric acid. The composition xerogel exhibits strong blue emission at room temperature, with an emission maximum at 434 nm under short (234 nm) or long-wavelength (343 nm) ultraviolet excitation. The photoluminescent excitation spectrum of the mixed tin and manganese oxide xerogel, monitored at an intensity maximum wavelength of 434 nm of the emission, consists of two excitation peaks at 234 nm and 343 nm. With heat treatment temperature increasing from 110 ℃ to 200 ℃, the blue emission intensity increases remarkably, whereas it is almost completely quenched after being treated at 300 ℃. The carbon impurities in the mixed tin and manganese oxide xerogel, confirmed by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy, should be responsible for the bright blue photoluminescence.     

大口径方光束片状放大器小信号增益实验研究

 介绍了一台24cm×24cm的大口径钕玻璃片状放大器,并且在不同充电电压下进行了实验测试。在充电电压为22kV、泵浦能密度为14.62J/cm ³的条件下,获得了4.9%cm ^-1的小信号增益系数和2.43%的储能效率。     

Rear-surface light intensification caused by a Hertzian-conical crack in 355-nm silica optics

Theoretical studies show that a Hertzian-conical crack can be considered to be composed of double cone faces for simplicity. In the present study, the three-dimensional finite-difference time-domain method is employed to quantify the electric-field distribution within the subsurface in the presence of such a defect under normal incidence irradiation. Both impurities (inside the crack) and the chemical etching have been investigated. The results show that the maximum electric field amplitude |E| max is 9.57374 V/m when the relative dielectric constant of transparent impurity equals 8.5. And the near-field modulation will be improved if the crack is filled with the remainder polishing powders or water vapor/drops. Meanwhile, the laser-induced initial damage moves to the glass-air surface. In the etched section, the magnitude of intensification is strongly dependent on the inclination angle θ. There will be a highest modulation when θ is around π/6, and the maximum value of |E| max is 18.57314 V/m. When θ ranges from π/8 to π/4, the light intensity enhancement factor can easily be larger than 100, and the modulation follows a decreasing trend. On the other hand, the modulation curves become smooth when θ > π/4 or θ < π/8.     

Fe纳米颗粒嵌埋对类金刚石薄膜结构及电学性能的影响

采用脉冲激光气相沉积方法制备了不同Fe嵌埋浓度的Fe: DLC多层纳米复合薄膜。用X射线光电子能谱仪(XPS)对薄膜的组成成分进行分析。利用透射电子显微镜（TEM）、拉曼光谱、电流-电压曲线研究Fe纳米颗粒嵌埋对薄膜的微观结构及电学性能的影响。XPS和TEM表明,Fe纳米颗粒周期性地均匀地嵌埋在碳薄膜中。拉曼光谱表明薄膜中的C为典型的类金刚石结构,Fe纳米颗粒促进芳香环式结构的形成,薄膜结构的有序度提高。电流 电压曲线表明,Fe纳米颗粒的嵌埋导致薄膜的室温电导率增加。     

Incident laser modulation of a repaired damage site with a rim in fused silica rear subsurface

Local CO2 laser treatment has proved to be an effective method to prevent the 351-nm laser-induced damage sites in a fused silica surface from exponentially growing, which is responsible for limiting the lifetime of optics in high fluence laser systems. However, the CO2 laser induced ablation crater is often surrounded by a raised rim at the edge, which can also result in the intensification of transmitted ultraviolet light that may damage the downstream optics. In this work, the three-dimensional finite-difference time-domain method is developed to simulate the distribution of electrical field intensity in the vicinity of the CO2 laser mitigated damage site located in the exit subsurface of fused silica. The simulated results show that the repaired damage sites with raised rims cause more notable modulation to the incident laser than those without rims. Specifically, we present a theoretical model of using dimpled patterning to control the rim structure around the edge of repaired damage sites to avoid damage to downstream optics. The calculated results accord well with previous experimental results and the underlying physical mechanism is analysed in detail.     

熔石英表面损伤修复点的损伤概率

针对3个光斑尺寸的CO2激光辐照尺寸小于400 m损伤点后得到的修复点,从4个方面对损伤修复点经355 nm激光辐照后的损伤概率分别进行研究。结果表明,根据修复光斑尺寸或损伤点尺寸分别讨论修复点的损伤概率,更能反映修复点的抗激光损伤能力。通过分别讨论可以看出,采用小光斑CO2激光辐照损伤点或者修复尺寸小于200 m的损伤点,修复成功率超过90%。同时,可以通过损伤修复点的激光损伤阈值都服从正态分布的规律来预测修复点的损伤概率。     

CO2激光局域辐照对熔石英损伤特性的影响

研究了CO₂激光局域辐照对熔石英损伤特性的影响, 发现当辐照中心温度较低时(1139 K), 辐照对损伤阈值没有明显影响, 但辐照中心温度较高时(1638 K), 辐照对损伤阈值有明显的影响, 损伤阈值随距离辐照中心间距的增大而减小, 在残余应力产生光程差最大处附近, 损伤阈值降到最小, 随着与辐照中心间距的进一步增加, 损伤阈值略有上升. 对导致此现象的原因做了分析. 由于残余应力的存在, 在辐照中心发生再损伤产生的裂纹后, 裂纹先沿径向扩展, 在残余应力产生光程差最大处附近, 裂纹转而向切向扩展, 这可能与径向和环向张应力随半径的变化有关. 在采用热处理炉退火消除残余应力时, 必须注意元件的洁净处理, 否则退火会出现析晶现象, 对损伤阈值和透射率造成不良影响. 关键词： 2激光局域辐照')" href="#">CO₂激光局域辐照 熔石英 损伤特性     

单通激光片状放大器的模拟计算分析

系统介绍了高功率固体激光驱动器中单口径片状放大器(SSA)的模拟和实验研究结果。根据放大器不同层次的设计需求，开发了两级模拟软件，配合实验模拟平台上的研究工作和结构研究，对SSA放大器进行系统设计。