Bright blue photoluminescence from a mixed tin and manganese oxide xerogel prepared via solben hydrothermalben gel process

A new blue photoluminescent material, a mixed tin and manganese oxide xerogel, is prepared via sol-hydrothermal-gel process assisted by citric acid. The composition xerogel exhibits strong blue emission at room temperature, with an emission maximum at 434 nm under short (234 nm) or long-wavelength (343 nm) ultraviolet excitation. The photoluminescent excitation spectrum of the mixed tin and manganese oxide xerogel, monitored at an intensity maximum wavelength of 434 nm of the emission, consists of two excitation peaks at 234 nm and 343 nm. With heat treatment temperature increasing from 110 ℃ to 200 ℃, the blue emission intensity increases remarkably, whereas it is almost completely quenched after being treated at 300 ℃. The carbon impurities in the mixed tin and manganese oxide xerogel, confirmed by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy, should be responsible for the bright blue photoluminescence.     

新型阵列式片状放大器全口径增益分布均匀性实验研究

利用CCD增益测试系统对一台闪光灯抽运、通光口径为 2 9cm× 2 9cm的新型高功率固体激光阵列式片状放大器的增益分布进行了实验测试 ,在充电电压为 2 3kV、抽运能密度为 11J/cm3 的条件下 ,新型 4× 2× 3阵列式片状放大器全口径范围内的小信号增益系数的峰值与平均值之比为 1.10∶1。     

单通激光片状放大器的模拟计算分析

系统介绍了高功率固体激光驱动器中单口径片状放大器(SSA)的模拟和实验研究结果。根据放大器不同层次的设计需求，开发了两级模拟软件，配合实验模拟平台上的研究工作和结构研究，对SSA放大器进行系统设计。     

Thermal distortion and birefringence in repetition-rate plasma electrode Pockels cell for high average power

We numerically study thermally induced birefringence and distortion in plasma electrode Pockels cell based on KD*P as the electro-optic material. This device can repetitively operate under the heat capacity mode. Simulation results indicate that the excellent switching performances and low wave-front distortion are achieved within several tens seconds working time at average power in excess of 1 kW.     

光参量啁啾脉冲放大系统非线性晶体长度确定及调谐方法研究

首先介绍了模拟光参量啁啾脉冲放大（OPCPA）过程的多种计算模型,在此基础上提出了三步走逐步逼近算法,以确定OPCPA过程中最稳输出时所需的非线性晶体长度.这种算法综合利用了上述计算模型,随着计算模型越来越精确,非线性晶体长度的计算范围越来越小.因而利用这种算法能高效、精确地确定最佳非线性晶体长度.最后提出在OPCPA过程引入一定的相位失配量,来调谐最稳输出时所需晶体长度,从而能突破晶体加工精度不够的局限,在实际OPCPA过程中获得稳定输出.     

Fe纳米颗粒嵌埋对类金刚石薄膜结构及电学性能的影响

采用脉冲激光气相沉积方法制备了不同Fe嵌埋浓度的Fe: DLC多层纳米复合薄膜。用X射线光电子能谱仪(XPS)对薄膜的组成成分进行分析。利用透射电子显微镜（TEM）、拉曼光谱、电流-电压曲线研究Fe纳米颗粒嵌埋对薄膜的微观结构及电学性能的影响。XPS和TEM表明,Fe纳米颗粒周期性地均匀地嵌埋在碳薄膜中。拉曼光谱表明薄膜中的C为典型的类金刚石结构,Fe纳米颗粒促进芳香环式结构的形成,薄膜结构的有序度提高。电流 电压曲线表明,Fe纳米颗粒的嵌埋导致薄膜的室温电导率增加。     

高功率固体激光器光学元件面形评价参数

结合高功率固体激光器的发展,说明了高功率光学元件面形评价参数的产生原因、发展过程及其内在因素。介绍了面形评价参数的现状,并通过讨论各面形评价参数之间的内在联系,说明了现行评价参数的综合性能及发展趋势。     

4×2×3阵列式放大器参数测量系统优化设计

 采用软边光阑和多级空间滤波器组合技术实现了光束的空间整形和等像面传输，利用Fresnel光束传输计算程序对4×2×3阵列式放大器参数测量系统进行了优化设计，分析了空间滤波器中小孔尺寸对光束波面传输的影响，并对优化设计结果进行了分析和讨论，所用方法和所得结论对高功率固体激光放大系统的设计有应用意义。     

大口径方光束片状放大器小信号增益实验研究

 介绍了一台24cm×24cm的大口径钕玻璃片状放大器,并且在不同充电电压下进行了实验测试。在充电电压为22kV、泵浦能密度为14.62J/cm ³的条件下,获得了4.9%cm ^-1的小信号增益系数和2.43%的储能效率。     

High temperature thermal behaviour modeling of large-scale fused silica optics for laser facility

High temperature annealing is often used for the stress control of optical materials.However,weight and viscosity at high temperature may destroy the surface morphology,especially for the large-scale,thin and heavy optics used for large laser facilities.It is necessary to understand the thermal behaviour and design proper support systems for large-scale optics at high temperature.In this work,three support systems for fused silica optics are designed and simulated with the finite element method.After the analysis of the thermal behaviours of different support systems,some advantages and disadvantages can be revealed.The results show that the support with the optical surface vertical is optimal because both pollution and deformation of optics could be well controlled during annealing at high temperature.Annealing process of the optics irradiated by CO2 laser is also simulated.It can be concluded that high temperature annealing can effectively reduce the residual stress.However,the effects of annealing on surface morphology of the optics are complex.Annealing creep is closely related to the residual stress and strain distribution.In the region with large residual stress,the creep is too large and probably increases the deformation gradient which may affect the laser beam propagation.