Detection of Tumor Necrosis Factor Gene by Piezoelectric Nucleic Acid Senosr

A piezoelectric nucleic acid sensor was constructed ofr detection of tumor necrosis factor gene.Two methods were employed for immobilization of nucleic acid probe on gold electrode of piezoelectric crystal.The results show that polyethyleneimine adbesion and glutaraldehyde cross-linking method has higher sensitivity,stability and selectivity than protein A method.The solid-phase nucleic acid hybridization of oligo unclecotides and tumor necrosis factor target gene sequence were monitorde using this sensor.Tumor necrosis factor gene sequence(580bp) was detected by this nucleic acid sensor for the first time.     

O—（1—甲硫基乙叉胺基）硫代磷酰胺（酯）的合成及生物活性…

首次报道了甲硫基乙醛肟与硫代磷酰氯的缩合反应，合成了１６种新型Ｏ－（１－甲硫基乙叉胺基）硫代磷酰胺酯及硫代磷酸酯类化合物，化合物６ｂ具有很好的杀虫活性。     

一种新的滤纸基质固体表面低温荧光(燐光)测定装置

对自行研制的铜制滤纸基质低温荧光（燐光）测定的样品支架，进行了滤纸基质固体表面低温荧光测定的可行性研究。与同类冷冻装置和室温装置比较，本装置用于滤纸基质固体表面低温荧光（燐光）测定具有以下优点；样品的分析周期大大地缩短，由45min缩短为5-6min；装置简单、便宜耐用；操作简便，简化了室温测定时的滤纸干燥程序，应用范围广，方法的重现性好，检样分析结果的相对标准偏差RSD%小于10%，荧光（燐光）分析灵敏度高，检出限低，线性范围宽。     

CrN镀层的微粒磨损性能及其切削行为研究

在Teer UDP 550型闭合场非平衡磁控溅射离子镀设备上制备CrN镀层,以球-盘方法测定的比磨损率和微粒磨损法测定的微粒磨损率评价CrN镀层的耐磨性能,采用高速钢镀层钻头的钻孔数评价镀层的切削性能.结果表明,CrN镀层的微粒磨损率对氮流量(用光谱发射因子OEM值控制)的变化很敏感,而比磨损率却不能反映这种由于氮流量变化带来的镀层结构和性能的变化.在不同偏压条件下所制备的镀层微粒磨损率变化不明显.当微粒磨损率低于某一值时,CrN镀层的钻孔寿命明显提高,而比磨损率则无此规律.     

功能肽段介导的铜离子荧光传感器的构建及应用

铜离子是导致多种疾病(如阿尔茨海默病、朊病毒病和肌萎缩性侧索硬化症等)的重要因素.当前已有针对铜离子检测的相关报道,但基于多肽与铜离子相互作用的荧光传感器鲜有关注.该文依据淀粉样蛋白与铜离子特异性结合的特点,利用已知的淀粉样蛋白组成单元,设计出能与铜离子有序配位的多肽分子(DDAEGHARHCR).同时,借助于"多肽-...     

Room-Temperature Magnetism Realized by Doping Fe into Ferroelectric LiTaO3

We synthesize LiTal-x FexO3-σ （LTFO） remain single phase up to x = 0.09 ceramics by the conventional solid-state reaction method. The samples The magnetic measurements show that the doping of Fe successfully realizes ferromagnetism of LTFO at room temperature. The dielectric measurements indicate that LTFO is ferroelectric, similarly to LiTaO3 （LTO）, but its ferroelectric Curie temperature seems to decrease with the increasing Fe content. By means of doping Fe ions into LTO, the coexistence of spontaneous electric polarization and spontaneous magnetic moment is realized at room temperature.     

熔石英后表面坑点型划痕对光场调制的近场模拟

建立了坑点型划痕的旋转抛物面模型, 用三维时域有限差分方法研究了熔石英后表面坑点型划痕随深度、 宽度、 间距以及酸蚀量变化对波长λ =355 nm入射激光的调制.研究表明, 这类划痕调制最强区位于相邻两坑点的连接区, 且越靠近表面调制越强.当其宽深比为2.0---3.5、 坑点间距约为坑点宽度的1/2时, 可获得最大光场调制, 最大光强增强因子(LIEF)为11.53; 当坑点间距大于坑点宽度时, 其调制大为减弱, 相当于单坑的场调制.对宽为60δ (δ =λ/12), 深和间距均为30δ的坑点型划痕进行刻蚀模拟, 刻蚀过程中最大LIEF为11.0, 当间距小于300 nm时, 相邻坑点由于衍射形成场贯通.     

Two localized CO2 laser treatment methods for mitigation of UV damage growth in fused silica

Two methods：high-power,short-time,single-shot irradiation（Method A） and low-power,long-time,multi-shot irradiation（Method B） are investigated to mitigate the UV damage growth in fused silica by using a 10.6-μm CO2 laser.To verify the mitigation effect of the two methods,the laser induced damage thresholds（LIDTs） of the mitigated sites are tested with a 355-nm,6.4-ns Nd：YAG laser,and the light modulation of the mitigation sites are tested with a 351-nm continuous Nd：YLF laser.The mitigated damaged sites treated with the two methods have almost the same LIDTs,which can recover to the level of pristine material.Compared with Method A,Method B produces mitigated sites with low crater depth and weak light modulation.In addition,there is no raised rim or re-deposited debris formed around the crater edge for Method B.Theoretical calculation is utilized to evaluate the central temperature of the CO2 laser beam irradiated zone and the radius of the crater.It is indicated that the calculated results are consistent with the experimental results.     

横向划痕对光场调制的近场模拟

熔石英亚表面划痕对入射激光的近场调制是导致光学元件低阈值损伤的主要因素之一. 用三维时域有限差分方法研究了连续横向划痕的近场分布, 对比了尖锐截面与光滑截面场调制的差异, 着重探讨了光场调制与划痕宽深比R的关系. 研究表明: 酸蚀后的光滑截面有助于减弱近场调制, 这类划痕的R>10.0时调制较弱且相互接近, R<5.0时调制显著增强. 当R取1---3时, 亚表面的调制达最大值, 最大电场幅值为入射波幅值的4.3倍. 当R取1.0---3.5时, 缺陷附近有80%以上取样点的最大电场幅值超过入射波幅值的2倍. 随着深度的增大, 强场区具有明显的"趋肤效应": 位于划痕正下方的强场区首先往左右两侧移动, 然后移向抛物口界面以及水平界面, 同时衍生出的多条增强线诱导整个亚表面层的光场增强.     

长链超支化聚合物的合成研究进展

长链超支化聚合物(HyperMacs)凭借其含有大量的功能端基和可调控的链结构等优点已经引起国内外科研人员越来越广泛的关注。HyperMcs除了拥有超支化聚合物固有的低粘度、溶解性好、含有大量的功能性端基的特点外,同时拥有高剪切敏感性、熔体弹性、冲击强度和零剪切粘度,因而在药物载体、能量存储及传递和纳米催化剂等方面可能拥有更为广泛的应用。本文根据HyperMacs合成方法的不同,分别从迭代法和ABx线型大分子单体法两个主要方面对其研究进展进行了总结和评述,并在此基础上展望了该类聚合物的研究方向和发展趋势。