CYP2C9酶与Warfarin结合模型的立体选择性理论研究

对CYP2C9酶与S-Warfarin复合物的晶体结构进行分子对接、分子动力学模拟、通道分析及结合自由能计算,发现原晶体结构中的结合模式为"亚稳态",提出了CYP2C9与S-Warfarin结合的可催化模式;比较了CYP2C9与S-和R-Warfarin结合的异同,确定了在结合过程中起重要作用的锚定氨基酸残基,尤其是位于活性位点区域的苯丙氨酸簇.在结合过程中这些残基通过芳香环的移动对稳定底物的结合模式起到至关重要的作用,阐明了该酶呈现相关底物选择性的原因.对于CYP2C9与底物对接模式及立体选择性的研究有助于在分子层面上理解特异性底物与酶的结合特点,为潜在的药物设计提供了合理可信的理论依据.     

可控表面磷原子修饰提升超细W2C纳米颗粒电解水析氢反应性能

研究高活性和稳定性的非贵金属基析氢催化剂对解决当前能源危机和环境污染问题具有重要意义.碳化钨具有与贵金属Pt类似的d带电子结构,因而成为一类新兴的非贵金属析氢催化剂,受到广泛关注.磷掺杂是提高催化剂析氢活性的有效方法之一,然而目前最常见的构筑磷掺杂方法是使用多金属氧酸盐(POMs,如H3PW12O40),其固定的W/P原子比导致W2C中的掺杂浓度难以调控,并且磷掺杂主要是进入碳载体而不是碳化物本身,从而导致无法明确杂原子对其电催化析氢活性的贡献.本文采用植酸(PA)为磷源设计合成了可控磷掺杂W2C纳米颗粒,并探讨了催化剂组分、杂原子掺杂位置与析氢性能之间的关系.深入研究了磷掺杂碳化钨(WCP)的化学结构和析氢活性.与原始的W2C催化剂相比,WCP具有更高的本征活性、更快的电子转移速率和更多的活性位数量,并且在酸性和碱性条件下均表现出较好的析氢性能.特别是过电位为-200 mV时,WCP催化剂的本征活性在酸性和碱性条件下分别为0.07和0.56 H2 s-1,高出纯W2C(0.01和0.05 H2 S-1)数倍.同时,在电流密度为-10 mA cm-2时,优化后的WCP催化剂在酸性和碱性条件下的析氢过电位分别降低了96和88 mV.XPS及EDS元素分析结果表明,随磷源添加量增加,磷掺杂从碳化钨表面逐渐向内部扩散,进一步说明磷取代位置与析氢活性之间的构效关系,高浓度的表面磷取代可以加速质子捕获过程,从而显著提高其析氢活性,而过量的内部磷取代会破坏W2C结构,降低电子转移速率,从而导致析氢性能下降.利用密度泛函理论计算深入研究了WCP具有较好析氢性能的原因,与内部磷取代相比,表面磷取代会使碳化钨表现出更合适的氢吸附自由能,并且更加有效地降低了氢释放势垒,从而优化了析氢反应动力学.综上,本文为元素掺杂工艺提供了新的思路,同时研究了表面异质原子对析氢活性的关键作用,为该类催化材料的构效关系研究提供了新思路.     

超声法合成CePO4纳米线及发光性能研究

用CeO2作为铈源,采用可重复利用的H3PO4及非模板剂的情况下,用低温超声法成功合成了六方结构的CePO4一维纳米线材料。用X-射线粉末衍射(XRD)、透射电镜(TEM)和荧光分光光度计(FL)测试样品的物相结构、微观形貌、颗粒尺寸和发光性能;并研究超声时间和PO3-4/Ce3+摩尔比对产物的形貌和荧光性能的影响。结果表明:实验所做出的样品全部是六方晶系的结构,形貌都为一维纳米线,其纳米线长50~200nm,宽5~40nm左右;不同超声时间和PO3-4/Ce3+摩尔比的纳米线长径比不同,随超声时间的延长和PO3-4/Ce3+摩尔比增大纳米线出现团聚现象,产物在250~300nm处有宽的激发峰,在378nm处有一个发射峰,是属于Ce3+的5d-4f能级跃迁。     

不同防老剂对天然橡胶复合材料P-V-T关系的影响

采用PVT膨胀仪测试了添加不同防老剂的天然橡胶(NR)复合材料的压力-体积-温度(P-V-T)属性,通过最小二乘法拟合得到Tait方程参数,预测了体系的热膨胀系数(α)和等温压缩系数(β),结果表明,Tait状态方程可用来预测该复合材料体系的P-V-T行为,NR复合材料的α值随着压力的增大而减小,随温度变化不明显;β值随压力的增大而减小,且随着温度的升高而升高.分子模拟结果观察了体系凝聚态结构在不同温度下的变化,表明其变化原因是升温使体系自由体积增大,分子链的活动性增强,同时观察到单独加入防老剂4010NA或防老剂RD的体系α和β的值较大,说明其尺寸稳定性差,而当同时加入4010NA和RD进行防老剂并用时,体系的α和β值均较小,表明此复合材料体系不容易产生变形;通过分子动力学模拟手段计算了NR复合材料的内聚能密度(CED)随温度的变化规律,对于2种防老剂并用的体系,其CED比较大,说明分子间相互作用力较强,从而体系尺寸稳定性好,受温度和压力的影响小.     

不同品种环保橡胶填充油对乳聚丁苯橡胶性能影响研究

通过使用差示扫描量热仪(DSC)、橡胶加工分析仪(RPA)和动态压缩生热仪测试,分别研究了采用国内外不同品种的环保型橡胶填充油所制备的乳聚丁苯橡胶的热性能、动态力学性能以及动态压缩生热性能,并与非环保型丁苯橡胶SBR1712及环保型丁苯橡胶SBR1723进行了对比。结果表明,采用环保型芳烃油(TDAE)所制备的乳聚丁苯橡胶损耗因子最大,生热稍高于其它品种环保油;采用克拉玛依石化环保型环烷油(AP-10)所制备的乳聚丁苯橡胶动态压缩生热性能最好。     

Study of In Situ Formation of Magnesium Hydroxide Whisker via Basic Magnesium Chloride Whisker Regulated by Organic Parcels at Low Temperature

In this work, we demonstrate an in situ phase conversion from basic magnesium chloride（BMC） into magnesium hydroxide whisker by using polar organic solvent at low temperature. The morphology and phase composition of magnesium hydroxide whiskers prepared at different reaction temperature, alkali concentration and organic solvent were analyzed by X-ray diffraction（XRD） and scanning electronic microscope（SEM）. It was found that when one of the organic solvents such as absolute ethyl alcohol, butanol, polyethylene glycol（PEG-400）, acetone, et al. was selected as the template, the precursor BMC can transform into whisker-like magnesium hydroxide through precipitate transformation in low temperature and non-hydrothermal system. It can be reasonably explained that the regulation of Mg^2＋ solubility by those organic solvents and the sustained release of Mg^2＋ dissolution by organic adsorption played a significant role in the formation of magnesium hydroxide whisker via BMC whisker as the precursor.     

Vulcanization kinetics of graphene/styrene butadiene rubber nanocomposites

This paper presents the influence of graphene on the vulcanization kinetics of styrene butadiene rubber （SBR） with dicumyl peroxide. A curemeter and a differential scanning calorimeter were used to investigate the cure kinetics, from which the kinetic parameters and apparent activation energy were obtained. It turns out that with increasing graphene loading, the induction period of the vulcanization process of SBR is remarkably reduced at low graphene loading and then levels off; on the other hand, the optimum cure time shows a monotonous decrease. As a result, the vulcanization rate is suppressed at first and then accelerated, and the corresponding activation energy increases slightly at first and then decreases. Upon adding graphene, the crosslinking density of the nanocomposites increases, because graphene takes part in the vulcanization process.     

Three Zinc(Ⅱ) Complexes Based on 2-Carboxylic Acid-4-nitropyridine-1-oxide: Synthesis,Crystal Structure,and Fluorescence Properties

Three new metal-organic complexes, namely [Zn(POA)2(H2O)2](1), [Zn(POA)2(H2O)2]·2H2O(2) and [Zn(POA)2]n(3), have been synthesized by organic ligand 2-carboxylic acid-4-nitropyridine-1-oxide(POA) and zinc(Ⅱ) ions. The structures of complexes 1~3 are characterized by single-crystal X-ray analysis, XRD powder diffraction analysis, infrared spectroscopy and thermal stability analysis method. Complex 1 belongs to monoclinic system, space group C2/c with a = 22.8215(15), b = 7.5613(16), c = 10.048(3) ?, β = 109.47°, V = 1634.7(6) ?~3, Z = 4, F(000) = 944, Dc = 1.900 g/cm^3, C(12)H(10)N4O(12)Zn, Mr = 467.61 and μ = 1.584 mm^-1. The whole molecule presents "V" shape. Complex 2 is a centrosymmetric structure in triclinic system with space group P1: a = 7.4728(5), b = 7.6825(6), c = 8.5184(6) ?, α = 65.975(2), β = 79.87(2), γ = 89.855(2)°, V = 4384.1(5) ?~3, Z = 1, F(000) = 256, Dc = 1.908 g/cm^3, C(12)H(14)N4O(14)Zn, Mr = 503.64 and μ = 1.492 mm^-1. Complex 3 is a one-dimensional chain structure belonging to monoclinic system and space group P21/c with a = 4.9456(6), b = 12.5322(14), c = 11.2514(13) ?, β = 97.313(11)°, V = 6916.8(14) ?~3, Z = 2, F(000) = 432, Dc = 2.072 g/cm^3, C(12)H6N4O(10)Zn, Mr = 431.58, and μ = 1.852 mm^-1. In three complexes, six oxygen atoms from the surrounding coordination atoms form a ZnO6 distorted octahedral coordination geometry around the zinc ions. Meanwhile, fluorescent properties of the three complexes were investigated at room temperature. The fluorescence spectroscopic analysis demonstrated that the ligand POA shows red-shift after coordinating with the zinc(Ⅱ) ions.     

轴流式水轮机三维非定常湍流计算及压力脉动预测

水轮机的稳定性研究是目前工程上大型水轮机组流动分析的重要课题,本文以某水电站的大型轴流转桨式水轮机原型为基础建立计算模型,完成了从蜗壳进口到尾水管出口整个流道的非定常湍流计算,预测了固定导叶进口、转轮后、尾水管进口等多个位置的压力脉动,并利用FFT变换进行分析得到了压力脉动的频率和幅值,探讨了水轮机全流道内压力脉动产生和传播的原理．     

液晶光阀的电光色散特性研究

分析液晶光阀(LCLV)的电光色散特性,重点研究扭曲向列型液晶光阀TB3639的电光色散特性。在温度为27 ℃时, 将TB3639液晶光阀置于频率为1 000 Hz的交流电场中,测出电光特性T-λ曲线,同时得到不同波长的T-V电光特性曲线,确定对比度与光波波长的函数关系k(λ),并得出电光色散特性关系曲线k(λ)～λ。分析结果表明, TB3639液晶光阀在可见光区域,具有相对较高的对比度,其色散较小。波长在450～750 nm区域其对比度均大于0.8;其中波长在550～670 nm区域其对比度变化不大,均大于0.95,其色散最小。