Interpretation of the polyelectrolyte and antipolyelectrolyte effects of poly(N‐vinylimidazole‐co‐sodium styrenesulfonate) hydrogels

Hydrogels of N‐vinylimidazole (VI) and sodium styrenesulfonate (SSS) were synthesized in aqueous solution by radical crosslinking copolymerization with N,N′‐methylene‐bis(acrylamide) as crosslinker. Swelling in several saline solutions was measured for hydrogel samples synthesized with different comonomer concentrations (C_T = 10, 25, or 40%) and with SSS mole fractions covering a broad range (f_SSS = 0–0.7), while the crosslinker ratio was 2 wt % in all cases. The degree of swelling in aqueous solution with a specific ionic strength (μ), plotted versus the SSS composition of the feed, shows a minimum for any set of samples synthesized with a fixed C_T. The dependence of swelling on μ shows both polyelectrolyte (f_SSS beyond the minimum) and antipolyelectrolyte behaviors (in the low f_SSS limit). It was found that the nonGaussian factor of the crosslinking density and the polymer‐solvent interaction parameter increase with f_SSS for any C_T. Moreover, in the low f_SSS limit, the osmotic swelling pressure is governed not only by the ionic contribution, but also by the polymer‐solvent mixing and, the concentration of mobile counterions inside the gel is not proportional to the net fixed charge but to the addition of cationic and anionic side groups, what discards the formation of ionic pairs. The antipolyelectrolyte effect is interpreted as due to the increasing protonation of VI as μ goes up. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1683–1693, 2007     

CAS based approach for discussing subset construction

This paper continues the discussion of teaching nondeterminism (see [6]) where we presented a didactic approach introducing the notion of nondeterministic automata. Although in this paper we use the same methodology we have to face up to new didactic challenges. Namely, teaching the subset construction requires answers to the question how can CAS be used in teaching the different phases of mathematical problem solving so that we can reach higher cognitive efficiency.     

Synthesis of polysiltrimethylenes with trimethylsilyl groups in the branch of the main chain

The thermally initiated and platinum-catalyzed polymerization of 1-silacyclobutanes with substitutents containing a trimethylsilyl group was carried out. Soluble, high-molecular-weight, heterochain siltrimethylene polymers were obtained, containing trimethylsilyl groups removed from the main chain by various bridges.A. V. Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, 117912 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 1, pp. 223–225, January, 1992.     

Application of microwave digestion to the preparation of sediment samples for arsenic speciation

Several extraction procedures are described allowing arsenic speciation in sediments. The extraction of organometallic compounds such as dimethylarsinic acid or monomethylarsonic acid is quite simple since these compounds are stable in the different extraction media (HCl/ HNO₃, H₃PO₄, ammonium oxalate) and are easily released independent of the extraction mode (magnetic stirring or microwave solubilization). Extraction yields are higher than 96% for these two arsenic forms. An HCl/HNO₃ microwave solubilization procedure allows the quantitative solubilization of mineral arsenic, but the differentiation between the two oxidation states is not possible owing to the oxidation of As(III) to As(V). Extractions with orthophosphoric acid or ammonium oxalate allow the solubilization of mineral arsenic with extraction yields ranging from 90 to 95% and the differentiation between As(III) and As(V). Nevertheless, the amount of As(III) is underestimated owing to its partial oxidation. The usefulness and advantages of microwave solubilization compared with conventional extraction procedures are discussed. Received: 17 May 1996 / Revised: 19 September 1996 / Accepted: 25 September 1996     

Use of spheron for separating flavonoids

Institute of Biology, Ufa Scientific Center, Russian Academy of Sciences, Ufa, fax (3472) 35 6103. Translated from Khimiya Prirodnykh Soedinenii, No. 5, pp. 755-756, September-October, 1995. Original article submitted September 6, 1994.     

On the ordering in [(C2H5)4N]2CuCl4 crystal: an X-ray study and theoretical considerations

The crystal structure [(C₂H₅)₄N]₂CuCl₄ has been determined by X-ray diffraction at 243K. The room temperature phase (phase I) belongs to the space group P4₂/nm [1] whereas the low temperature phase (phase II) is orthorhombic and belongs to the space group Pnna. The phase transition at T_c=258K is of improper ferroelastic type and it is associated with the ordering of the CuCl₄ ^2? and a partial ordering of the [(C₂H₅)₄N]⁺ ions which are disordered in the high temperature tetragonal phase. At lower temperature, there occurs another instability which could correspond to a complete ordering in the crystal.     

Corner spontaneous magnetization

Details are given of a new method allowing an exact calculation of the spontaneous magnetization in the corner as well as along the edge at an arbitrary distance of the corner for a rectangular planar Ising ferromagnet.     

Rotational temperature and density measurements in a hypersonic flow by dual-line CARS

Rotational temperature and nitrogen number density are measured in the shock wave/boundary layer interaction region in the vicinity of a two-dimensional compression corner disposed in a low pressure, 55 K, Mach 10 hypersonic air flow. Spatially-resolved data are recorded using a nonlinear optical technique named dual-line coherent anti-Stokes Raman scattering (DLCARS). Averaged temperature and density profiles are compared with those predicted by a Navier-Stokes solver. Good agreement is found.     

Cems characterization of SnO2 films obtained by sputtering and sol-gel route

Conversion electron Mössbauer spectroscopy (CEMS) has been used to study tin oxide films prepared by sol-gel dipping and sputtering. The spectra of films prepared by sol-gel route result close to that of crystalline SnO₂ after heat treatment at a temperature as low as 150°C. The Mössbauer parameters of as sputter deposited films indicate that the structure of the deposited stannic oxide has an amorphous character more pronounced for thinner samples. The structure becomes predominantly that of crystalline SnO₂ by heating at 550°C for 30 min provided the film thickness is higher than 10 nm.