Förster energy transfer from poly(arylene–ethynylene)s to an erbium–porphyrin complex

We study the infrared emission at 1.54 μm of an organolanthanide complex, Er(III)-tetraphenylporphyrin [Er(TPP)acac], both as a result of direct optical excitation and via energy transfer from host π-conjugate polymers of type poly(arylene–ethynylene) [PAE]. In the first case, the emission of the neat complex is characterized in inert transparent materials and a value of the quantum yield at 1.54 μm φ_IR=4×10⁻⁴ is measured. Then, fluorescence resonance transfer is investigated in blends of Er(TPP)acac with PAEs by monitoring the quenching of the polymer fluorescence along with the enhancement of both the visible emission of the ligand and the near-infrared band of Er³⁺. These different procedures allow a detailed analysis of the transfer efficiency within a specific implementation of the Förster model for polymeric donors. The experimental values of the critical radius R₀, ranging from 1.3 to 2.5 nm for the different blends, are in good agreement with theory for a wide interval of the physical and spectroscopic parameters. This suggests that other mechanisms for excitation transfer do not play a significant role in these materials.     

乌桕类可可脂结晶过程中表现体积变化

为了解乌桕类可可脂(CTCBE)缓冷结晶横向胀罐爆裂原因，研究CTCBE结晶过程中的膨胀特性，采用流体静力法测试了不同等温结晶条件下CTCBE结晶形成的表观密度和表观体积及其横纵向膨胀状况。结果表明，CTCBE缓冷结晶后形成外部和中部两个晶区。在5-25℃的各等温结晶范围内，当结晶温度增加时，外部结晶区域减小、表观密度变化不大；中部结晶区域增大、表观密度明显减小，CTCBE的表观体积、横向、纵向膨胀率均增大，膨胀横向大于纵向。进一步表明CTCBE在自然缓冷固化的表观体积根本上由其结晶温度决定。为有效防止横向胀罐，自然缓冷固化温度应低于10℃。     

Resistivity－temperature characteristics of sol gel YBa2Cu3Oy samples synthesized in flowing oxygen atmosphere

The relationship of resistivity versus synthesizing temperature of sol gel YBa_2Cu_3O_y samples was studied when prepared under flowing oxygen conditions. A set of high-temperature ρ－T curves was obtained for the whole process. After the sample finished the test measuring, its resistivity was ρ_{300}=9.83×10^{-3 }Ω·cm at room temperature. The ρ－T curve also showed that the orthorhombic－tetragonal phase transformation of sol-gel YBa_2Cu_3O_y sample occurred at 581℃ for the sample in the rising temperature process, but at 613℃ in the cooling process, lower than that of the samples made by using the conventional powder metallurgy methods.     

A fast method to measure the thickness of removed layer from etching of SSNTD based on EDXRF

Solid state nuclear track detectors are commonly used for measurements of concentrations of radon gas and/or radon progeny. All these measurements depend critically on the thickness of the removed layer during etching. However, the thickness of removed layer calculated using the etching period does not necessarily provide a sufficiently accurate measure of the thickness. For example, the bulk etch rate depends on the strength of stirring during etching for the LR 115 detector. We propose here to measure the thickness of the removed layer by using energy-dispersive X-ray fluorescence spectrometry. In the present work, a reference silver nitrate pellet is placed beneath the LR 115 detector, and the fluorescence X-ray intensity for silver is then measured. We have found a linear relationship between the X-ray intensity and the thickness of the removed layer for LR 115 detector. This provides a fast method to measure the thickness of removed layer from etching of LR 115 detector. However, this method was found to be inapplicable for the CR-39 detector. Therefore, alternative methods have yet to be explored for the CR-39 detector.     

Volumetric and infrared measurements on amorphous ice structure

We have simultaneously used adsorption isotherm volumetry and Fourier transform infrared spectroscopy in order to take the investigations on amorphous ice structure a step further, especially concerning porosity and annealing-induced modifications. We have studied surface reorganization during annealing and found that the number of surface sites decreases before crystallization, their relative ratios being different for amorphous and crystalline ice. We also present results confirming that ice can have a large specific surface area and nevertheless be non-microporous.     

单光子态的产生与测量

报道了通过自发参量下转换产生单光子态的实验研究,使用中心波长425 nm的飞秒脉冲泵浦Ⅰ类非共线相位匹配的BBO晶体,在实验上得到单光子计数率为2.978×10-4,并分析了实验中的相关问题.     

Characterizations of Tb:Zn2SiO4 films on silicon wafer prepared by sol-gel dip-coating and solid-phase reaction

Terbium-doped Zn_2SiO_4 films were successfully prepared on Si wafers by a simple sol-gel dip-coating and solid-phase reaction method of ZnO and SiO_2. X-ray diffraction (XRD) and UV－Vis absorption results revealed that films processed below 850℃ were ZnO in wurzite structure, and films processed above 850℃ were Zn_2SiO_4 in wellimite structure. Photoluminescence measurements of the Tb-doped Zn_2SiO_4 films showed two strong emission bands at 490 and 545nm. The photoluminescence lifetime was 4.6ms.     

碳纳米管阵列、捆束的三步升温工艺制备及其形貌与结构

使用结构简单的单温炉设备，通过三步升温热解二茂铁、三聚氰氨混合物方法，在二氧化硅、多晶陶瓷基底上分别合成了碳纳米管阵列、碳纳米管捆束.使用扫描电子显微镜、透射电子显微镜、电子能量损失谱和x射线光电子能谱对合成样品进行了结构和成分分析.结果显示：两种基底上合成的纳米管均为多壁纯碳管；生长于光滑二氧化硅表面的碳纳米管具有高度取向性和一致的外径，长度为10—40μm.碳纳米管采取催化剂顶端生长模式并展示出类杯状形貌；生长于粗糙多晶陶瓷表面的碳纳米管捆束随机取向，碳纳米管直径为15—80nm，长度在几百微米，展示 关键词： 碳纳米管 热解法 三步升温工艺     

Synthesis and Photophysical Properties of Ferrocene Containing Monomer and Polymer

Synthesis of a new monomer and polymer containing both ferrocene and hydrazone moieties are reported. The obtained materials were examined by various techniques including differential scanning calorimetry, UV, IR, NMR spectroscopy, and time of flight method. These materials may be of particular interest for the development of future electrophotographic photoreceptors as electron photoemission spectra of the layers showed ionization potentials of 5.35–5.41 eV. The hole drift mobility values in compositions of the designed structures with bisphenol Z polycarbonate exceeded 10⁻⁸ cm²/Vs at strong electric fields.