Microwave-assisted extraction of quercetin and acid degradation of its glycosides in Psidium guajava leaves.

Microwave-assisted extraction (MAE) and microwave-assisted hydrolysis (MAAH) were developed for the sample preparation of guava leaves prior to GC determination of quercetin and its glycosides. Ethanol was selected as the solvent. The optimum MAE temperature, particle size, solvent volume and MAE time are 120 degrees C, 40 - 60 mesh, 20 mL and 5 min, respectively; the optimum MAAH temperature and time, HCl concentration, solvent are 100 degrees C, 5 min, 1.2 mol L(-1) HCl and ethanol, respectively.     

Fluorescent-based single-strand conformation polymorphism/heteroduplex capillary electrophoretic mutation analysis of the P53 gene.

Fluorescent-based single-strand conformation polymorphism (F-SSCP) analysis with capillary electrophoresis (CE) is the most common method for the detection of mutation because of its high sensitivity and resolution. In this study, we prepared an inexpensive linear polyacrylamide (LPA), and successfully applied it to CE-SSCP analysis and tandem CE-SSCP/heteroduplex analysis (HA) of the P53 gene on an ABI capillary genetic analyzer. A comparison of the sieving capabilities of a homemade LPA and commercial polydimethylacrylamide (PDMA) demonstrates that the homemade LPA has a higher resolution, a shorter analysis time, and is more suitable for tandem SSCP/HA than commercial PDMA. To show the usefulness, mutations of P53 gene exon 7 - 8 in 37 tumor samples were investigated by using homemade LPA. The results indicate that 10 mutations were found in 9 of 37 cases; the majority of P53 mutations were missense mutations, and 70% were located in exon 7, which plays an important role in neoplastic progression in human tumorigenesis.     

NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

Ceramic Films via Organometallic Complex as Single Source Precursor

Fe2(CO)6(μ-S2) was used as a single source precursor in attempt to produce FeS film via MOCVD. Pyrolysis of Fe2(CO)6(μ-S2) at temperature below 500℃ produced Fe1-xS or Fe7S8 powder as indicated by its powder X-ray spectra. At 750 ℃, polycrystalline FeS powder was obtained. In film deposition, polycrystalline Fe1-xS or Fe7Ss films were obtained on Si(100) and Ag/Si(100) substrates below 500 ℃. SEM micrographs showed the film on Si(100) substrate containing whisker like grains. However, pillar like grains were obtained on Ag/Si(100) substrate.Deposition rates are also different for different substrates as evaluated by the thickness of the films, which were obtained by SEM micrographs of the cross section of the films. At 750℃, similar polycrystalline Fe1-xS or Fe7S8 film was obtained.     

A monotone iterative scheme for a nonlinear second order equation based on a generalized anti–maximum principle

In this paper, a generalized anti–maximum principle for the second order differential operator with potentials is proved. As an application, we will give a monotone iterative scheme for periodic solutions of nonlinear second order equations. Such a scheme involves the L^p norms of the growth, 1 ≤ p ≤ ∞, while the usual one is just the case p = ∞.     

Spectra Analysis of a Novel Ti-Doped LiAlO2 Single Crystal

LiAlO2 single crvstals doped with Ti at concentration 0.2at.% are grown by the Czochralskl technique with dimensions φ42×55mm. Ti ions in the crystal are quadrivalence proven by comparing the absorption and fluorescence spectra of pure LiAlO2 and Ti： LiAlO2. After air and Li-rich atmosphere annealing, the absorption peaks in the range of 600-800nm disappear. We conclude that 682 and 756nm absorption peaks are attributed to the VLi and Vo absorptions, respectively： The peaks at 716nm and 798nm may stem from the VLi^＋ and absorptions. The colour-centre model can be applied to explain the experimental phenomena. Ti^4＋-doping produces more lithium vacancies in the LiAlO2 crystal. The intensities of [LiO4] and the associated bonds remain unchanged, which improves the anti-hydrolyzation and thermal stability of LiAlO2 crystals.     

On a Generalized Cochrane Sum and Its Hybrid Mean Value Formula

The main purpose of this paper is to use a mean value theorem of Dirichlet L-functions to study the asymptotic property of a hybrid mean value of a generalized Cochrane sum, and give an interesting mean value formula.2000 Mathematics Subject Classification: Primary—11F20; Secondary—11F99     

The accurate dimensional measurements within small internal structures

This paper shows that the dimension of internal structure of a component can be measured remotely to a resolution better than 5 μm by use of the combination of high resolution optical microscopy and image processing.A specialised high resolution, long working distance and diffraction limited lens was used to image within the component. A series of digital images were made to map spatially the interior of the component. An edge detector was then used to localise the specific location of features in order that an accurate internal measurement could be made. A visualisation of the internal surface finish was also achieved.