Argon sorption and partial molar volume in poly(ethyl methacrylate) above and below the glass transition temperature

Sorption and dilation isotherms for argon in poly(ethyl methacrylate) (PEMA) are reported for pressures up to 50 atm over the temperature range 5–85°C. At temperatures below the glass transition (T_g=61°C), sorption isotherms are well described by the dual-mode sorption model; and isotherms above T_g follow Henry's law. However, isotherms for dilation due to sorption are linear in pressure at all temperatures over the range investigated. Partial molar volumes of Ar in PEMA are obtained from these isotherms. The volumes are approximately constant above T_g (about 40 cm³/mol), whereas the volumes below T_g are smaller and dependent on both temperature and concentration (19–26 cm³/mol). By analyzing the experimental data according to the dual-mode sorption and dilation model, the volume occupied by a dissolved Ar molecule and the mean size of microvoid in the glass are estimated to be 67 129 ų, respectively. The cohesive energy density of the polymer is also estimated as 61 cal/cm³ from the temperature dependence of the dual-mode parameters.     

Application of total reflection X-ray fluorescence spectrometry to small glass fragments.

Total reflection X-ray fluorescence spectrometry (TXRF) has been applied for trace elemental analysis of small glass fragments. A small glass sample (a fragment with weight less than 0.5 mg) was decomposed by 100 microg of HF/HNO3 acid; the material was condensed to 10 microl and was dried on a Si wafer. Since the size of the dried residue on the Si wafer was less than 1 cm in diameter, an incident X-ray beam with about 1 cm in width could effectively excite elemental components in such a small glass fragment. The precision of the present technique was checked by analyzing the glass fragments (<0.5 mg) from NIST SRM612; the relative standard deviations (RSD) of less than 8.1% were achieved for elemental ratios that were normalized by Sr. Fragments (<0.5 mg) obtained from 23 figured sheet glasses were used as samples for estimating the utility of this technique to forensic discrimination. Comparison of five elemental ratios of Ti/Sr, Mn/Sr, Zn/Sr, Rb/Sr, and Pb/Sr calculated from X-ray fluorescence spectra was effective in distinguishing glass fragments that could not be differentiated by their refractive indexes (RI).     

Pit your wits against young minds!

This column is a place for those bits of contagious mathematics that travel from person to person in the community, because they are so elegant, suprising, or appealing that one has an urge to pass them on. Contributions are most welcome.     

Electromagnetophoretic force measurement of a single binding interaction between lectin and yeast cell surfaces.

A novel measurement method of the binding force between a micrometer-sized particle and a solid surface in an electrolyte solution has been established by using the electromagnetophoretic buoyancy on the particle. By this method, we investigated the binding force between a yeast cell surface and an oligosaccharide-binding protein, concanavalin A (Con A), fixed on a silica capillary wall. The force measurement was carried out up to 60 pN. In a lower surface concentration of Con A, yeast cells could be desorbed by a force less than 60 pN. However, in a higher surface concentration after treated by 1 mg ml(-1) solution, yeast cells were adsorbed with a force stronger than 60 pN. In this case, the addition of 10 mg ml(-1) D-mannose solution to the medium reduced the binding force to less than 60 pN. The observed adsorption force of yeast cells ranged within 30 - 40 pN, regardless of the interfacial amount of Con A. This force was thought to be the single binding force between a mannose group of the cell surface and an active site of Con A. Moreover, the dissociation rate constant of the single binding of yeast cell and Con A complex was determined as 4.6 x 10(-3) s(-1) and the increment of the binding distance at the transition state as 0.33 nm from the desorption kinetic experiments of yeast cell under the constant pulling conditions of 10, 20 and 30 pN. Such satisfactory results demonstrate the novel advantages of the present method.     

Atomistic phenomena in dense fluid shock waves

The shock structure problem is one of the classical problems of fluid mechanics and at least for non-reacting dilute gases it has been considered essentially solved. Here we present a few recent findings, to show that this is not the case. There are still new physical effects to be discovered provided that the numerical technique is general enough to not rule them out a priori. While the results have been obtained for dense fluids, some of the effects might also be observable for shocks in dilute gases.     

Approximation of transient temperatures in complex geometries using fractional derivatives

It is shown that time-dependent temperatures in a transient, conductive system can be approximately modeled by a fractional-order differential equation, the order of which depends on the Biot number. This approximation is particularly suitable for complex shapes for which a first-principles approach is too difficult or computationally time-consuming. Analytical solutions of these equations can be written in terms of the Mittag-Leffler function. The approximation is especially useful if a suitable fractional-order controller is to be designed for the system.     

Damage and fracture evaluation of granular composite materials by digital image correlation method

This paper presents the applications of digital image correlation technique to the mesoscopic damage and fracture study of some granular based composite materials including steelfiber reinforced concrete, sandstone and crystal-polymer composite. The deformation fields of the composite materials resulted from stress localization were obtained by the correlation computation of the surface images with loading steps and thus the related damage prediction and fracture parameters were evaluated. The correlation searching could be performed either directly based on the gray levels of the digital images or from the wavelet transform (WT) coefficients of the transform spectrum. The latter was developed by the authors and showed higher resolution and sensitivity to the singularity detection. Because the displacement components came from the rough surfaces of the composite materials without any coats of gratings or fringes of optical interferometry, both surface profiles and the deformation fields of the composites were visualized which was helpful to compare each other to analyze the damage of those heterogeneous materials. The project supported by the National Natural Science Foundation of China (10125211 and 10072002), the Scientific Committee of Yunnan Province for the Program of Steel Fiber Reinforced Concrete, and the Institute of Chemical Materials, CAEP at Mianyang