Sonochemical preparation of composite nanoparticles of Au/gamma-Fe2O3 and magnetic separation of glutathione

We prepared Au/gamma-Fe2O3 composite nanoparticles by sonochemically reducing Au(III) ions employing no stabilizer in the aqueous solution to form stable Au nanoparticles and allowing them to attach onto the surface of gamma-Fe2O3 particles with an average size of 21 nm. Size of the formed Au nanoparticle depended on the initial concentration of Au(III) ions. The number of the Au nanoparticles, supported on each gamma-Fe2O3 particle was controlled by changing the relative amounts of Au(III) ions and gamma-Fe2O3 particles. The composite nanoparticles exhibited a high affinity with glutathione, a tripeptide with mercapto group so that separation and manipulation of glutathione in aqueous solutions could be performed by application of external magnetic field. Because the surfaces of the Au nanoparticles were not shielded by any stabilizers, or naked, sonochemically prepared Au/gamma-Fe2O3 composite nanoparticles seemed to show stronger affinity to the glutathione than those by the radiochemical method.     

Microchip capillary electrophoresis with a boron-doped diamond electrochemical detector for analysis of aromatic amines

The attractive features of a boron-doped diamond (BDD) thin-film detector for microchip capillary electrophoretic (CE) separations of dye-related amino-substituted aromatic compounds are described. The diamond electrode was employed in the end-column amperometric detection of 4-aminophenol (4-AP), 1,2-phenylenediamine (1,2-PDA), 2-aminonaphthalene (2-AN), 2-chloroaniline (2-CA), and o-aminobenzoic acid (o-ABA), and its attractive behavior was compared to commonly used screen-printed carbon and glassy-carbon electrodes. These conventional electrode materials exhibit a significant degree of passivation and low sensitivity to the above-mentioned environmental pollutants. The diamond-based electrochemical detection system displayed a favorable analytical performance, including lower noise levels, higher peak resolution with enhanced sensitivity, and improved resistance against electrode passivation. Factors influencing the on-chip analysis were assessed and optimized. The diamond detector displayed detection limits of 2.0 and 1.3 microM for 4-AP and 2-AN, respectively, and a wide linear response for these compounds over the 2-50 microM range. The enhanced stability was demonstrated by relative standard deviation (RSD) values of 1.4% and 4.7% for 100 microM 1,2-PDA and 200 microM 2-CA, respectively, for repetitive detections (n = 7). Besides, the simultaneously observed current decrease was 2.4 and 9.1% for 1,2-PDA and 2-CA, respectively (compared to 21.8 and 41.0% at the screen-printed carbon electrode and 28.3 and 34.1% at the glassy carbon electrode, respectively). The favorable properties of the diamond electrode indicate great promise for environmental applications in CE and other microchip devices.     

Ruthenium catalyzed addition reaction of carboxylic acid across olefins without beta-hydride elimination

The cationic ruthenium catalyst (Cp*RuCl2)2/AgOTf/Ligand promotes the addition reaction of carboxylic acids across olefins without beta-hydride elimination.     

Photorefractive effect in the relaxor ferroelectric material 0.91Pb(Zn1/3Nb2/3)O3-0.09PbTiO3

The photorefractive effect in a nominally undoped 0.91Pb(Zn1/3Nb2/3)O3-0.09PbTiO3 single crystal is measured. We report what is, to our knowledge, the first observation of the photorefractive effect in Pb-based relaxor ferroelectric crystals. The crystal is grown by the flux solution method. Then it is cut into a 2 mm x 4 mm x 8 mm piece and electrically poled along the [111] direction. The coupling constant of the two-wave mixing is 17 cm(-1), and the normalized time constant under 1-W/cm(2) illumination is 12 s at a wave-length of 476 nm. The effective trap density is calculated as 5 x 10(16) cm(-3) from the Debye screening length under the assumption of Kukhtarev's band-transport model. The dominant carrier is identified to be holes from the direction of two-wave mixing energy transfer.     

Synthesis and isomerization of conjugated oligomers containing azoimidazole unit

The Suzuki (for O1 – O3 ) and Stille (for O4 ) coupling polymerization of 2‐(phenylazo)imidazole bearing the benzyl protecting group at the 1‐position gave conjugated oligomers. The transformation from the neutral imidazole in the conjugated oligomer O2 , consisted of the alternating 2,5‐didecyl‐1,4‐phenylene unit, to the cationic imidazolium salt O2S was performed. Depending on the chemical structure of coupling partners, the absorption maximum of conjugated oligomers showed red shift or blue shift from that of the model compound M with the benzene ring at the 4,5‐positions. The absorption maximum wavelength of the cationic conjugated oligomer O2S showed a blue shift from that of the neutral conjugated oligomer O2 . The trans‐to‐cis photoisomerization of the azoimidazole unit in conjugated oligomers was observed by irradiating the light at 436 nm, and the conversion degree to the cis structure had a rough correlation with the maximum absorption wavelength of materials. The trans‐to‐cis photoisomerization in the film state was sluggish. On the other hand, the cis‐to‐trans thermal isomerization of the azoimidazole unit was confirmed and the absorbance returned to the initial state before the photoisomerization. The trans‐to‐cis photoisomerization of the cationic conjugated oligomer O2S required large energy, and the prolonged light irradiation might decompose the azoimidazole unit. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Molecular orientation and mechanical anisotropy of polypropylene sheet containing N,N′‐dicyclohexyl‐2,6‐naphthalenedicarboxamide

Effect of mixing and processing conditions at T‐die extrusion on the structure and mechanical properties is studied for isotactic polypropylene (PP) containing a small amount of β‐form nucleating agent, N,N′‐dicyclohexyl‐2,6‐naphthalenedicarboxamide. It is found that trigonal β crystals are predominantly formed in the extruded samples containing the nucleating agent irrespective of the mixing and processing conditions, leading to the marked mechanical toughness. On the contrary, the molecular orientation is significantly affected by the mixing and processing conditions. In particular, it should be noted that PP molecules in the extruded sheet which was mixed at high temperature (260 °C) and extruded at low temperature (200 °C) orient perpendicular to the applied flow direction. As a result, the sheet shows anomalous mechanical anisotropy. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 424–433, 2009