Viscosity,particle size distribution,and structural investigation of tetramethyloxysilane/2‐hydroxyethyl methacrylate sols during the sol–gel process with acid and base catalysts

The tetramethoxysilane (TMOS)/2‐hydroxylethyl methacrylate (HEMA) hybrid gels were synthesized with acid and base catalysts, via the in situ polymerization of HEMA, with and without the cosolvent methanol. With methanol in the TMOS/HEMA sol, the enhanced esterification and depolymerization reactions of the silanols resulted in a slower growth of silica particles. The silica particles that were synthesized with an acid catalyst were less than 40 nm. The thermal resistance of the poly(2‐hydroxyethyl methacrylate) (PHEMA) chains was enhanced by the addition of colloidal silica. The Fourier transform infrared characterizations and the exothermal peaks on the differential scanning calorimetry traces of these hybrid gels indicated chemical hybridization occurring as a result of condensation of the colloid silica and PHEMA at higher temperatures. Hence, the residual weight content of the hybrid gel after its synthesis with the base catalyst was even higher than the content of TMOS in the hybrid sol. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3476–3486, 2004     

Novel fixed‐site–carrier polyvinylamine membrane for carbon dioxide capture

Fixed‐site–carrier membranes were prepared for the facilitated transport of CO₂ by casting polyvinylamine (PVAm) on various supports, such as poly(ether sulfone) (PES), polyacrylonitrile (PAN), cellulose acetate (CA), and polysulfone (PSO). The cast PVAm on the support was crosslinked by various methods with glutaraldehyde, hydrochloric acid, sulfuric acid, and ammonium fluoride. Among the membranes tested, the PVAm cast on polysulfone and crosslinked by ammonium fluoride showed the highest selectivity of CO₂ over CH₄ (>1000). The permeance of CO₂ was then measured to be 0.014 m³ (STP)/(m² bar h) for a 20 μm thick membrane. The effect of the molecular weight of PVAm and feed pressure on the permeance was also investigated. The selectivity increased remarkably with increasing molecular weight and decreased slightly with increased pressure in the range of 1 to 4 bar. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4326–4336, 2004     

Pressure and temperature dependence of the gas‐transport properties of dense poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] membranes

The gas‐transport properties of poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] (6FDA‐2,6‐DAT) have been investigated. The sorption behavior of dense 6FDA‐2,6‐DAT membranes is well described by the dual‐mode sorption model and has certain relationships with the critical temperatures of the penetrants. The solubility coefficient decreases with an increase in either the pressure or temperature. The temperature dependence of the diffusivity coefficient increases with an increase in the penetrant size, as the order of the activation energy for the diffusion jump is CH₄ > N₂ > O₂ > CO₂. Also, the average diffusion coefficient increases with increasing pressure for all the gases tested. As a combined contribution from sorption and diffusion, permeability decreases with increases in the pressure and the kinetic diameter of the penetrant molecules. Even up to 32.7 atm, no plasticization phenomenon can be observed on flat dense 6FDA‐2,6‐DAT membranes from their permeability–pressure curves. However, just as for other gases, the absolute value of the heat of sorption of CO₂ decreases with increasing pressure at a low‐pressure range, but the trend changes when the feed pressure is greater than 10 atm. This implies that CO₂‐induced plasticization may occur and reduce the positive enthalpy required to create a site into which a penetrant can be sorbed. Therefore, a better diagnosis of the inherent threshold pressure for the plasticization of a glassy polymer membrane may involve examining the absolute value of the heat of sorption as a function of pressure and identifying the turning point at which the gradient of the absolute value of the heat of sorption against pressure turns from a negative value to a positive one. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 354–364, 2004     

Relationship between the dynamic softening transition and wet sliding friction of elastomer compounds

For properly chosen elastomer compounds, thermorheological characterization is combined with an examination of the variation of the wet sliding friction with temperature. A conceptual argument leads to the assumption that the wet sliding friction should maximize at the energy dissipation peak associated with the dynamic softening transition at a characteristic frequency determined by the sliding speed and the effective smallest surface asperity scale. The dynamic softening transition is characterized with the peak in tan δ/G′ⁿ, where tan δ is the loss tangent, G′ is the elastic modulus, and n is a constant between 0 and 1. The William–Landel–Ferry transform is uncritically applied for extrapolating the position of the peak in tan δ/G′ⁿ at high frequencies. Even based on the criterion of tan δ, the results obtained on a concrete surface indicate that the effective smallest asperity scale is of order of 100 μm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2467–2478, 2004     

Differential scanning calorimetry and thermogravimetric analysis investigation of the thermal properties and degradation of some radiation‐grafted films and membranes

The influence of irradiation and grafting on the crystallinity of three base polymers has been investigated with differential scanning calorimetry. Grafting has the largest effect on the base polymer crystallinity and results in a reduction of the crystallinity. The thermal degradation of the base polymers and grafted films has been investigated with thermogravimetric analysis. The extent of the fluorination of the base polymer, the irradiation method, and the graft level all influence the thermal degradation and its activation energy. It is proposed that the variation of the chain lengths of the grafted polystyrene chains is actually a primary underlying factor responsible for the influence of these various parameters on the degradation process. The first results of a comparative thermal analysis of some fuel‐cell membranes are also presented, and the promise and shortcomings of this method are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2612–2624, 2004     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

Fabrication and Characteristics of Sol-Gel Derived Fluorinated Hybrid Material Films

Fluorinated inorganic-organic hybrid materials (HYBRIMER) were successfully prepared from fluoroalkylsilanes (FASs) containing fluoro-alkyl functions and methacryloxypropyltrimethoxysilane (MPTMS) through a sol-gel process. The influence of concentration and fluoro-alkyl chain lengths of FASs on the physical characteristics of the fluorinated HYBRIMER films was examined. Larger fluorine contents lowered the refractive index within a range, which was closely dependent on the fluoro-alkyl chain lengths of FASs. Thermo-optic coefficients (TOC) were negative values, and the values grew with increasing fluorine contents and fluoro-alkyl chain lengths. Also, the thermal stability is enhanced by addition of fluorine in the HYBRIMER.     

氟代吡啶阳离子的理论研究

利用量子化学密度泛函理论B3LYP方法及 6 31G(d ,p)、6 311G(d ,p)、6 31+G(d ,p)和 6 311+G(d ,p)基组对五氟代吡啶、2 ,6 二氟代吡啶和 2 氟代吡啶分子的阳离子进行了计算研究 .B3LYP构型优化和频率分析计算结果表明这三种氟代吡啶阳离子的结构分别具有C2v、C2v和Cs 对称性 ,电子基态分别为2 A2 、2 A2 和2 A″ .对离子和分子的计算构型做了比较 .利用B3LYP方法和不同的基组对这三种阳离子及其分子进行了自然布居分析计算 .用B3LYP方法对这三种阳离子 (自由基 )中的超精细结构进行了计算 ,对五氟代吡啶、2 ,6 二氟代吡啶和2 氟代吡啶分子的垂直电离势和绝热电离势进行了计算 ,与实验值符合得很好     

(Nd_(1-x)Er_x)_2Co_(15.5)V_(1.5)的结构转变与磁性

利用电弧熔炼制备了 (Nd1 xErx) 2 Co1 5 5V1 5(x=0— 1 0 )化合物样品 .通过x射线衍射分析和磁性测量研究了Er替代Nd2 Co1 5 5V1 5中的Nd时对化合物结构和磁性的影响 .研究结果表明 ,低Er含量 (x <0 4 ) ,化合物为Th2 Zn1 7型结构 ;高Er含量时 (x >0 5 ) ,化合物转变为Th2 Ni1 7结构 ;Er含量为x =0 4和 0 5时 ,两种结构共存 .两种结构的晶胞参数a ,c和晶胞体积V随着Er含量的增加都呈现递减的趋势 .随着Er含量的增加 ,(Nd1 xErx) 2 Co1 5 5V1 5化合物的居里温度和饱和磁化强度都单调下降 .(Nd1 xErx) 2 Co1 5 5V1 5化合物的室温各向异性由低Er含量时的易锥型转变为高Er含量时的易轴型 .x =0— 0 5的化合物在温度升高时发生自旋重取向转变 ,自旋重取向温度Tsr随Er含量的增加而减小     

聚乙烯基咔唑与Alq3混合薄膜的发光性能与能量传递过程

研究了Alq3与聚乙烯基咔唑(PVK)按不同比例的混合体系制备的薄膜的发光特性.通过对混合薄膜的吸收光谱、激发光谱和发射光谱的分析，研究了PVK与Alq3之间的 能量传递规律.当Alq3与PVK的质量比为1∶7时，能量传递效率最高.用一个由单链模 型扩展到包括杂质的哈密顿量对实验进行模拟，发现该模型能够较好地解释有关的实验结果. 关键词： 吸收光谱 激发光谱 发射光谱 能量传递